[hylafax-users] Problems with Tobit-Faxware/David as TX

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Problems with Tobit-Faxware/David as TX
From: roland klose <rkl.fritzbox@xxxxxx>
Date: Tue, 14 Sep 2004 12:05:12 +0200

Hi,

I've problems to receive documents if the sender use Tobit-Faxware/David.

On my Site I use HylaFAX 4.2.0 with Sitecom Modems (Cirrus Logic 
CL-MD56xx/CD08.55). Faxsetup doesn't find the right Modem first, so I now use 
the cirrus config file.

All runs best, only the above mentioned senders makes trouble.

Here is the excerpt form the receive log:

------ cut here --------

The full document was not received because:

    Failed to properly detect high-speed data carrier.

    ---- Transcript of session follows ----

Sep 13 15:24:39.35: [29289]: SESSION BEGIN 000002785 494222xxxxxx
Sep 13 15:24:39.35: [29289]: HylaFAX (tm) Version 4.2.0
Sep 13 15:24:39.35: [29289]: <-- [4:ATA\r]
Sep 13 15:24:42.47: [29289]: --> [7:CONNECT]
Sep 13 15:24:42.47: [29289]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Sep 13 15:24:42.48: [29289]: RECV FAX: begin
Sep 13 15:24:44.36: [29289]: --> [7:CONNECT]
Sep 13 15:24:45.11: [29289]: --> [7:CONNECT]
Sep 13 15:24:45.60: [29289]: --> [2:OK]
Sep 13 15:24:45.60: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:24:45.83: [29289]: --> [7:CONNECT]
Sep 13 15:24:47.48: [29289]: --> [2:OK]
Sep 13 15:24:47.48: [29289]: REMOTE TSI "+49 209 xxxxxx"
Sep 13 15:24:47.48: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:24:47.50: [29289]: --> [7:CONNECT]
Sep 13 15:24:47.75: [29289]: --> [2:OK]
Sep 13 15:24:47.75: [29289]: REMOTE wants 14400 bit/s
Sep 13 15:24:47.75: [29289]: REMOTE wants A4 page width (215 mm)
Sep 13 15:24:47.75: [29289]: REMOTE wants unlimited page length
Sep 13 15:24:47.75: [29289]: REMOTE wants 7.7 line/mm
Sep 13 15:24:47.75: [29289]: REMOTE wants 1-D MH
Sep 13 15:24:47.75: [29289]: REMOTE wants T.30 Annex A, 256-byte ECM
Sep 13 15:24:47.75: [29289]: RECV training at v.17 14400 bit/s
Sep 13 15:24:47.75: [29289]: <-- [11:AT+FRM=145\r]
Sep 13 15:24:49.28: [29289]: --> [7:CONNECT]
Sep 13 15:24:50.66: [29289]: RECV: TCF 2464 bytes, 0% non-zero, 2455 zero-run
Sep 13 15:24:50.66: [29289]: --> [10:NO CARRIER]
Sep 13 15:24:50.66: [29289]: DELAY 75 ms
Sep 13 15:24:50.74: [29289]: TRAINING succeeded
Sep 13 15:24:50.74: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:24:50.92: [29289]: --> [7:CONNECT]
Sep 13 15:24:52.20: [29289]: --> [2:OK]
Sep 13 15:24:52.20: [29289]: <-- [11:AT+FRM=146\r]
Sep 13 15:24:52.56: [29289]: --> [7:CONNECT]
Sep 13 15:24:52.98: [29289]: RECV received frame number 0
Sep 13 15:24:53.13: [29289]: RECV received frame number 1
Sep 13 15:24:53.34: [29289]: RECV received frame number 2
Sep 13 15:24:53.48: [29289]: RECV received frame number 3

....  many lines deleted (same text) ....

Sep 13 15:25:08.48: [29289]: RECV received frame number 105
Sep 13 15:25:08.63: [29289]: RECV received frame number 106
Sep 13 15:25:08.77: [29289]: RECV received frame number 107
Sep 13 15:25:08.91: [29289]: RECV received frame number 108
Sep 13 15:25:09.09: [29289]: RECV assumed RCP frame with block end
Sep 13 15:25:09.09: [29289]: --> [10:NO CARRIER]
Sep 13 15:25:09.09: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:25:09.12: [29289]: --> [7:CONNECT]
Sep 13 15:25:10.30: [29289]: --> [2:OK]
Sep 13 15:25:10.30: [29289]: RECV recv PPS (partial page signal)
Sep 13 15:25:10.30: [29289]: RECV recv EOP (no more pages or documents)
Sep 13 15:25:10.30: [29289]: RECV received 110 frames of block 1 of page 1
Sep 13 15:25:10.30: [29289]: DELAY 70 ms
Sep 13 15:25:10.37: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:10.55: [29289]: --> [7:CONNECT]
Sep 13 15:25:12.79: [29289]: --> [2:OK]
Sep 13 15:25:12.79: [29289]: RECV send PPR (partial page request)
Sep 13 15:25:12.79: [29289]: <-- [11:AT+FRM=146\r]
Sep 13 15:25:13.14: [29289]: --> [7:CONNECT]
Sep 13 15:25:13.61: [29289]: RECV assumed RCP frame with block end
Sep 13 15:25:13.61: [29289]: --> [10:NO CARRIER]
Sep 13 15:25:13.61: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:25:13.64: [29289]: --> [7:CONNECT]
Sep 13 15:25:14.82: [29289]: --> [2:OK]
Sep 13 15:25:14.82: [29289]: RECV recv PPS (partial page signal)
Sep 13 15:25:14.82: [29289]: RECV recv EOP (no more pages or documents)
Sep 13 15:25:14.82: [29289]: RECV received 1 frames of block 1 of page 1
Sep 13 15:25:14.82: [29289]: DELAY 70 ms
Sep 13 15:25:14.89: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:15.06: [29289]: --> [7:CONNECT]
Sep 13 15:25:17.30: [29289]: --> [2:OK]
Sep 13 15:25:17.30: [29289]: RECV send PPR (partial page request)
Sep 13 15:25:17.30: [29289]: <-- [11:AT+FRM=146\r]
Sep 13 15:25:17.65: [29289]: --> [7:CONNECT]
Sep 13 15:25:18.12: [29289]: RECV assumed RCP frame with block end
Sep 13 15:25:18.12: [29289]: --> [10:NO CARRIER]
Sep 13 15:25:18.12: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:25:18.15: [29289]: --> [7:CONNECT]
Sep 13 15:25:19.32: [29289]: --> [2:OK]
Sep 13 15:25:19.32: [29289]: RECV recv PPS (partial page signal)
Sep 13 15:25:19.32: [29289]: RECV recv EOP (no more pages or documents)
Sep 13 15:25:19.32: [29289]: RECV received 1 frames of block 1 of page 1
Sep 13 15:25:19.32: [29289]: DELAY 70 ms
Sep 13 15:25:19.39: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:19.57: [29289]: --> [7:CONNECT]
Sep 13 15:25:21.81: [29289]: --> [2:OK]
Sep 13 15:25:21.81: [29289]: RECV send PPR (partial page request)
Sep 13 15:25:21.81: [29289]: <-- [11:AT+FRM=146\r]
Sep 13 15:25:22.16: [29289]: --> [7:CONNECT]
Sep 13 15:25:22.63: [29289]: RECV assumed RCP frame with block end
Sep 13 15:25:22.63: [29289]: --> [10:NO CARRIER]
Sep 13 15:25:22.63: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:25:22.66: [29289]: --> [7:CONNECT]
Sep 13 15:25:23.84: [29289]: --> [2:OK]
Sep 13 15:25:23.84: [29289]: RECV recv PPS (partial page signal)
Sep 13 15:25:23.84: [29289]: RECV recv EOP (no more pages or documents)
Sep 13 15:25:23.84: [29289]: RECV received 1 frames of block 1 of page 1
Sep 13 15:25:23.84: [29289]: DELAY 70 ms
Sep 13 15:25:23.91: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:24.08: [29289]: --> [7:CONNECT]
Sep 13 15:25:26.32: [29289]: --> [2:OK]
Sep 13 15:25:26.32: [29289]: RECV send PPR (partial page request)
Sep 13 15:25:26.32: [29289]: RECV sent fourth PPR
Sep 13 15:25:26.32: [29289]: <-- [9:AT+FRH=3\r]
Sep 13 15:25:26.45: [29289]: --> [7:CONNECT]
Sep 13 15:25:27.60: [29289]: --> [2:OK]
Sep 13 15:25:27.60: [29289]: RECV recv CTC (continue to correct)
Sep 13 15:25:27.60: [29289]: DELAY 70 ms
Sep 13 15:25:27.67: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:27.85: [29289]: --> [7:CONNECT]
Sep 13 15:25:29.14: [29289]: --> [2:OK]
Sep 13 15:25:29.14: [29289]: RECV send CTR (confirm continue to correct)
Sep 13 15:25:29.14: [29289]: <-- [11:AT+FRM=145\r]
Sep 13 15:25:36.13: [29289]: RECV keeping unconfirmed page
Sep 13 15:25:36.30: [29289]: RECV: 28160 bytes of data, 2344 total lines
Sep 13 15:25:36.41: [29289]: --> [2:OK]
Sep 13 15:25:36.41: [29289]: RECV FAX (000002785): from +49 209 xxxxxx, page 1 
in 0:46, INF, 7.7 line/mm, 1-D MH, 14400 bit/s
Sep 13 15:25:36.41: [29289]: RECV FAX (000002785): recvq/fax000002749.tif from 
+49 209 xxxxxx, route to <unspecified>, 1 pages in 0:54
Sep 13 15:25:36.41: [29289]: RECV FAX: Failed to properly detect high-speed 
data carrier.
Sep 13 15:25:36.41: [29289]: <-- [9:AT+FTH=3\r]
Sep 13 15:25:36.59: [29289]: --> [7:CONNECT]
Sep 13 15:25:37.87: [29289]: --> [2:OK]
Sep 13 15:25:37.87: [29289]: RECV FAX (000002785): session with +49 209 xxxxxx 
terminated abnormally: Failed to properly detect high-speed data carrier.
Sep 13 15:25:37.88: [29289]: RECV FAX: bin/faxrcvd "recvq/fax000002749.tif" 
"ttyS0" "000002785" "Failed to properly detect high-speed data carrier." "" 
""
Sep 13 15:25:37.88: [29289]: RECV FAX: end
Sep 13 15:25:37.88: [29289]: SESSION END

--------------- cut again -------------

With the first used config from faxsetup I've this errors too, and "Failure to 
receive silence", "unspecified Phase D error" with several (not only 
Tobit-Faxware/David) Sender.

Any Idea, what I can do, to solve this problem?

greetings
Roland

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] Problems with Tobit-Faxware/David as TX
  - From: Matthias Reich
- Re: [hylafax-users] Problems with Tobit-Faxware/David as TX
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] libtiff3g
Next by Date: Re: [hylafax-users] Problems with Tobit-Faxware/David as TX
Previous by thread: Re: [hylafax-users] Problem receiving multiple pages
Next by thread: Re: [hylafax-users] Problems with Tobit-Faxware/David as TX
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services