[hylafax-users] Fax polling with HylaFAX 4.2

To: <hylafax-users@xxxxxxxxxxx>
Subject: [hylafax-users] Fax polling with HylaFAX 4.2
From: "Bodo Noering" <bn@xxxxxxxxxx>
Date: Tue, 17 Aug 2004 16:09:39 +0200
I have some problems using fax polling with new HylaFAX 4.2.

First, a log file of 4.1.7:

Aug 17 12:00:12.89: [23687]: SESSION BEGIN 00007631 49800444471100
Aug 17 12:00:12.89: [23687]: HylaFAX (tm) Version 4.1.7
Aug 17 12:00:12.89: [23687]: SEND FAX: JOB 1809 DEST 0800444471100
COMMID 00007631 DEVICE '/dev/ttyS1'
Aug 17 12:00:12.89: [23687]: MODEM set DTR OFF
Aug 17 12:00:12.89: [23687]: DELAY 75 ms
Aug 17 12:00:12.96: [23687]: MODEM set DTR ON
Aug 17 12:00:12.96: [23687]: DELAY 2600 ms
Aug 17 12:00:16.57: [23687]: MODEM set baud rate: 19200 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 17 12:00:16.57: [23687]: DELAY 10 ms
Aug 17 12:00:16.58: [23687]: MODEM flush i/o
Aug 17 12:00:16.58: [23687]: <-- [4:ATZ\r]
Aug 17 12:00:16.79: [23687]: --> [2:OK]
Aug 17 12:00:16.79: [23687]: DELAY 3000 ms
Aug 17 12:00:19.79: [23687]: <--
[34:AT&B1&N0&S0*F0S38.3=1S39=0S41.4=1\r]
Aug 17 12:00:19.82: [23687]: -->
[33:AT&B1&N0&S0*F0S38.3=1S39=0S41.4=1]
Aug 17 12:00:19.82: [23687]: --> [2:OK]
Aug 17 12:00:19.82: [23687]: <-- [5:ATE0\r]
Aug 17 12:00:19.83: [23687]: --> [4:ATE0]
Aug 17 12:00:19.83: [23687]: --> [2:OK]
Aug 17 12:00:19.83: [23687]: <-- [5:ATV1\r]
Aug 17 12:00:19.85: [23687]: --> [2:OK]
Aug 17 12:00:19.85: [23687]: <-- [5:ATQ0\r]
Aug 17 12:00:19.87: [23687]: --> [2:OK]
Aug 17 12:00:19.87: [23687]: <-- [7:ATS0=0\r]
Aug 17 12:00:19.89: [23687]: --> [2:OK]
Aug 17 12:00:19.89: [23687]: <-- [7:ATS8=2\r]
Aug 17 12:00:19.91: [23687]: --> [2:OK]
Aug 17 12:00:19.91: [23687]: <-- [8:ATS7=60\r]
Aug 17 12:00:19.93: [23687]: --> [2:OK]
Aug 17 12:00:19.93: [23687]: <-- [6:AT&H3\r]
Aug 17 12:00:19.95: [23687]: --> [2:OK]
Aug 17 12:00:19.95: [23687]: <-- [6:AT&D2\r]
Aug 17 12:00:19.97: [23687]: --> [2:OK]
Aug 17 12:00:19.97: [23687]: <-- [6:AT&C1\r]
Aug 17 12:00:19.99: [23687]: --> [2:OK]
Aug 17 12:00:19.99: [23687]: <-- [14:AT+FCLASS=2.0\r]
Aug 17 12:00:20.13: [23687]: --> [2:OK]
Aug 17 12:00:20.13: [23687]: <-- [9:AT+FLO=2\r]
Aug 17 12:00:20.15: [23687]: --> [2:OK]
Aug 17 12:00:20.15: [23687]: <-- [9:AT+FPP=0\r]
Aug 17 12:00:20.17: [23687]: --> [2:OK]
Aug 17 12:00:20.17: [23687]: <-- [9:AT+FBO=0\r]
Aug 17 12:00:20.19: [23687]: --> [2:OK]
Aug 17 12:00:20.19: [23687]: <-- [10:AT+FCT=30\r]
Aug 17 12:00:20.21: [23687]: --> [2:OK]
Aug 17 12:00:20.21: [23687]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 17 12:00:20.23: [23687]: --> [2:OK]
Aug 17 12:00:20.23: [23687]: <-- [9:AT+FIE=0\r]
Aug 17 12:00:20.25: [23687]: --> [2:OK]
Aug 17 12:00:20.25: [23687]: <-- [9:AT+FBU=1\r]
Aug 17 12:00:20.27: [23687]: --> [2:OK]
Aug 17 12:00:20.27: [23687]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Aug 17 12:00:20.30: [23687]: --> [2:OK]
Aug 17 12:00:20.30: [23687]: <-- [5:ATM0\r]
Aug 17 12:00:20.32: [23687]: --> [2:OK]
Aug 17 12:00:20.32: [23687]: STATE CHANGE: RUNNING -> SENDING
Aug 17 12:00:20.32: [23687]: MODEM input buffering enabled
Aug 17 12:00:20.32: [23687]: Apply DialString rules to
"0800444471100"
Aug 17 12:00:20.32: [23687]: --> return result "0800444471100"
Aug 17 12:00:20.32: [23687]: <-- [14:AT+FCLASS=2.0\r]
Aug 17 12:00:20.56: [23687]: --> [2:OK]
Aug 17 12:00:20.56: [23687]: <-- [9:AT+FLO=2\r]
Aug 17 12:00:20.68: [23687]: --> [2:OK]
Aug 17 12:00:20.68: [23687]: <-- [9:AT+FPP=0\r]
Aug 17 12:00:20.80: [23687]: --> [2:OK]
Aug 17 12:00:20.80: [23687]: <-- [9:AT+FBO=0\r]
Aug 17 12:00:20.92: [23687]: --> [2:OK]
Aug 17 12:00:20.92: [23687]: <-- [10:AT+FCT=30\r]
Aug 17 12:00:21.04: [23687]: --> [2:OK]
Aug 17 12:00:21.04: [23687]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 17 12:00:21.16: [23687]: --> [2:OK]
Aug 17 12:00:21.16: [23687]: <-- [9:AT+FIE=0\r]
Aug 17 12:00:21.28: [23687]: --> [2:OK]
Aug 17 12:00:21.28: [23687]: <-- [9:AT+FBU=1\r]
Aug 17 12:00:21.40: [23687]: --> [2:OK]
Aug 17 12:00:21.40: [23687]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Aug 17 12:00:21.53: [23687]: --> [2:OK]
Aug 17 12:00:21.53: [23687]: <-- [22:AT+FLI="Bodo Noering"\r]
Aug 17 12:00:21.66: [23687]: --> [2:OK]
Aug 17 12:00:21.66: [23687]: <-- [9:AT+FSP=1\r]
Aug 17 12:00:21.78: [23687]: --> [2:OK]
Aug 17 12:00:21.79: [23687]: DIAL 0800444471100
Aug 17 12:00:21.79: [23687]: <-- [20:ATDT0W0800444471100\r]
Aug 17 12:00:42.30: [23687]: --> [4:+FCO]
Aug 17 12:00:42.30: [23687]: --> [26:+FCI:08004444711          ]
Aug 17 12:00:42.30: [23687]: REMOTE CSI "08004444711"
Aug 17 12:00:42.30: [23687]: --> [20:+FIS:0,5,2,2,0,1,0,0]
Aug 17 12:00:42.30: [23687]: --> [4:+FPO]
Aug 17 12:00:42.30: [23687]: REMOTE has document to POLL
Aug 17 12:00:42.30: [23687]: --> [2:OK]
Aug 17 12:00:42.30: [23687]: REMOTE best rate 14400 bit/s
Aug 17 12:00:42.30: [23687]: REMOTE max page width 2432 pixels in 303
mm
Aug 17 12:00:42.30: [23687]: REMOTE max unlimited page length
Aug 17 12:00:42.30: [23687]: REMOTE best vres 3.85 line/mm
Aug 17 12:00:42.30: [23687]: REMOTE best format 1-D MR
Aug 17 12:00:42.30: [23687]: REMOTE supports T.30 Annex A, ECM
Aug 17 12:00:42.30: [23687]: REMOTE best 0 ms/scanline
Aug 17 12:00:42.30: [23687]: USE 14400 bit/s
Aug 17 12:00:42.30: [23687]: USE 0 ms/scanline
Aug 17 12:00:42.30: [23687]: STATE CHANGE: SENDING -> RECEIVING
Aug 17 12:00:42.30: [23687]: MODEM input buffering enabled
Aug 17 12:00:42.30: [23687]: POLL FAX: begin (SEP "", PWD "")
Aug 17 12:00:42.33: [23687]: Apply CanonicalNumber rules to
"+49.2054.9717"
Aug 17 12:00:42.33: [23687]: --> match rule "[^+0-9]+", result now
"+492054.9717"
Aug 17 12:00:42.33: [23687]: --> match rule "[^+0-9]+", result now
"+4920549717"
Aug 17 12:00:42.33: [23687]: --> return result "+4920549717"
Aug 17 12:00:42.33: [23687]: <-- [23:AT+FPI="+4920549717"\r]
Aug 17 12:00:42.45: [23687]: --> [2:OK]
Aug 17 12:00:42.45: [23687]: <-- [7:AT+FDR\r]
Aug 17 12:00:50.63: [23687]: --> [26:+FTI:08004444711          ]
Aug 17 12:00:50.63: [23687]: REMOTE TSI "08004444711"
Aug 17 12:00:50.63: [23687]: --> [20:+FCS:0,5,0,2,0,0,0,0]
Aug 17 12:00:50.63: [23687]: REMOTE wants 14400 bit/s
Aug 17 12:00:50.63: [23687]: REMOTE wants page width 1728 pixels in
215 mm
Aug 17 12:00:50.63: [23687]: REMOTE wants unlimited page length
Aug 17 12:00:50.63: [23687]: REMOTE wants 3.85 line/mm
Aug 17 12:00:50.63: [23687]: REMOTE wants 1-D MR
Aug 17 12:00:52.62: [23687]: --> [7:CONNECT]
Aug 17 12:00:52.62: [23687]: RECV: begin page
Aug 17 12:00:52.62: [23687]: RECV: send trigger 022
Aug 17 12:00:52.62: [23687]: <-- data [1]
Aug 17 12:01:10.80: [23687]: RECV/CQ: Bad 1D pixel count, row 1108,
got 0, expected 1728
Aug 17 12:01:10.80: [23687]: RECV/CQ: Bad 1D pixel count, row 1109,
got 0, expected 1728
Aug 17 12:01:10.80: [23687]: RECV/CQ: Bad 1D pixel count, row 1110,
got 0, expected 1728
Aug 17 12:01:10.80: [23687]: RECV/CQ: Bad 1D pixel count, row 1111,
got 0, expected 1728
Aug 17 12:01:10.80: [23687]: RECV/CQ: Bad 1D pixel count, row 1112,
got 0, expected 1728
Aug 17 12:01:10.80: [23687]: RECV: 32335 bytes of data, 1113 total
lines
Aug 17 12:01:10.80: [23687]: --> [16:+FPS:1,454,0,0,0]
Aug 17 12:01:12.02: [23687]: --> [6:+FET:2]
Aug 17 12:01:12.02: [23687]: RECV recv EOP (no more pages or
documents)
Aug 17 12:01:12.02: [23687]: --> [2:OK]
Aug 17 12:01:12.02: [23687]: RECV send MCF (message confirmation)
Aug 17 12:01:12.02: [23687]: RECV FAX (00007631): from 08004444711,
page 1 in 0:30, INF, 3.85 line/mm, 1-D MR, 14400 bit/s
Aug 17 12:01:12.02: [23687]: RECV FAX (00007631): recvq/fax04132.tif
from 08004444711, route to <unspecified>, 1 pages in 0:30
Aug 17 12:01:12.02: [23687]: <-- [7:AT+FDR\r]
Aug 17 12:01:14.80: [23687]: --> [7:+FHS:00]
Aug 17 12:01:14.80: [23687]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Aug 17 12:01:14.80: [23687]: POLL FAX: end
Aug 17 12:01:14.81: [23687]: RECV POLL: bin/pollrcvd "x@xxx"
"recvq/fax04132.tif" "ttyS1" "00007631" ""
Aug 17 12:01:15.71: [23687]: <-- [5:ATH0\r]
Aug 17 12:01:15.71: [23687]: --> [2:OK]
Aug 17 12:01:15.71: [23687]: MODEM set DTR OFF
Aug 17 12:01:15.85: [23687]: STATE CHANGE: RECEIVING -> MODEMWAIT
(timeout 5)
Aug 17 12:01:15.85: [23687]: SESSION END


Second, the log file of 4.2 (same number, same modem):

Aug 17 14:15:02.70: [31602]: SESSION BEGIN 000007640 49800444471100
Aug 17 14:15:02.70: [31602]: HylaFAX (tm) Version 4.2.0
Aug 17 14:15:02.70: [31602]: SEND FAX: JOB 1813 DEST 0800444471100
COMMID 000007640 DEVICE '/dev/ttyS0'
Aug 17 14:15:02.70: [31602]: STATE CHANGE: RUNNING -> SENDING
Aug 17 14:15:02.70: [31602]: MODEM input buffering enabled
Aug 17 14:15:02.70: [31602]: Apply DialString rules to
"0800444471100"
Aug 17 14:15:02.70: [31602]: --> return result "0800444471100"
Aug 17 14:15:02.70: [31602]: <-- [9:AT+FLO=2\r]
Aug 17 14:15:02.82: [31602]: --> [2:OK]
Aug 17 14:15:02.82: [31602]: <-- [9:AT+FPP=0\r]
Aug 17 14:15:02.94: [31602]: --> [2:OK]
Aug 17 14:15:02.94: [31602]: <-- [9:AT+FBO=0\r]
Aug 17 14:15:03.06: [31602]: --> [2:OK]
Aug 17 14:15:03.06: [31602]: <-- [10:AT+FCT=30\r]
Aug 17 14:15:03.18: [31602]: --> [2:OK]
Aug 17 14:15:03.18: [31602]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 17 14:15:03.30: [31602]: --> [2:OK]
Aug 17 14:15:03.30: [31602]: <-- [9:AT+FIE=0\r]
Aug 17 14:15:03.42: [31602]: --> [2:OK]
Aug 17 14:15:03.42: [31602]: <-- [9:AT+FBU=1\r]
Aug 17 14:15:03.54: [31602]: --> [2:OK]
Aug 17 14:15:03.54: [31602]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Aug 17 14:15:03.68: [31602]: --> [2:OK]
Aug 17 14:15:03.68: [31602]: <-- [9:AT+FSP=1\r]
Aug 17 14:15:03.79: [31602]: --> [2:OK]
Aug 17 14:15:03.79: [31602]: DIAL 0800444471100
Aug 17 14:15:03.79: [31602]: <-- [20:ATDT0W0800444471100\r]
Aug 17 14:15:23.56: [31602]: --> [4:+FCO]
Aug 17 14:15:23.56: [31602]: --> [26:+FCI:08004444711          ]
Aug 17 14:15:23.56: [31602]: REMOTE CSI "08004444711"
Aug 17 14:15:23.56: [31602]: --> [20:+FIS:0,5,2,2,0,1,0,0]
Aug 17 14:15:23.56: [31602]: --> [4:+FPO]
Aug 17 14:15:23.56: [31602]: REMOTE has document to POLL
Aug 17 14:15:23.56: [31602]: --> [2:OK]
Aug 17 14:15:23.56: [31602]: REMOTE best rate 14400 bit/s
Aug 17 14:15:23.56: [31602]: REMOTE max A3 page width (303 mm)
Aug 17 14:15:23.56: [31602]: REMOTE max unlimited page length
Aug 17 14:15:23.56: [31602]: REMOTE best vres 3.85 line/mm
Aug 17 14:15:23.56: [31602]: REMOTE best format 1-D MH
Aug 17 14:15:23.56: [31602]: REMOTE supports T.30 Annex A, 256-byte
ECM
Aug 17 14:15:23.56: [31602]: REMOTE best 0 ms/scanline
Aug 17 14:15:23.56: [31602]: USE 14400 bit/s
Aug 17 14:15:23.56: [31602]: USE 0 ms/scanline
Aug 17 14:15:23.56: [31602]: <-- [5:ATH0\r]
Aug 17 14:15:24.13: [31602]: --> [2:OK]
Aug 17 14:15:24.13: [31602]: MODEM set DTR OFF
Aug 17 14:15:24.13: [31602]: STATE CHANGE: SENDING -> MODEMWAIT
(timeout 5)
Aug 17 14:15:24.13: [31602]: SESSION END

It seems, that the modem doesn't change state from sending to
receiving.
I've tried it 3 times. There are no differences between old and new
"config.ttyS0" although I ran faxaddmodem after updating to 4.2.

Many thanks for any hint!


Best Regards
Bodo



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] Fax polling with HylaFAX 4.2
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] EQUINOX SST Multi-modem
Next by Date: [hylafax-users] 4.2.0 RPM for Fedora Core 1
Previous by thread: Re: [hylafax-users] EQUINOX SST Multi-modem
Next by thread: Re: [hylafax-users] Fax polling with HylaFAX 4.2
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services