Re: [hylafax-users] Unspecified Phase D error with MT5634ZBA-V92 MultiTech modem

["Darren Nickerson" <darren.nickerson@xxxxxxxx>]

You can get it from ftp://ftp.hylafax.org/source/BETA/

For more information on this upcoming release, and for links to binary
packages (like RPMs), see:

http://wiki.ifax.com/tiki-index.php?page=BetaTest

-Darren

--
Darren Nickerson
Senior Sales & Support Engineer
iFax Solutions, Inc. www.ifax.com
darren.nickerson@xxxxxxxx
+1.215.438.4638 x8106
+1.215.243.8335 (fax)

----- Original Message ----- 
From: "Steve Melo" <smelo@xxxxxxxxxxxxxxxxx>
To: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>; <hylafax-users@xxxxxxxxxxx>
Sent: Tuesday, July 27, 2004 2:16 PM
Subject: Re: [hylafax-users] Unspecified Phase D error with MT5634ZBA-V92
MultiTech modem


> I cannot find a link anywhere for the 4.2.0 distribution.  Where can it be
> downloaded?
>
> Thanks
>
>
>
>
> ----- Original Message -----
> From: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>
> To: "Steve Melo" <smelo@xxxxxxxxxxxxxxxxx>
> Cc: <hylafax-users@xxxxxxxxxxx>
> Sent: Tuesday, July 27, 2004 1:29 PM
> Subject: Re: [hylafax-users] Unspecified Phase D error with MT5634ZBA-V92
> MultiTech modem
>
>
> > On 2004.07.27 09:43 Steve Melo wrote:
> > > Greetings,
> > >
> > > Recently I obtained a MT5634ZBA-V92 MultiTech modem as suggested in
> > > the
> > > mailing list. Since then I have been receiving "Unspecified Phase D
> > > error"
> > > and I wonder if there is something wrong with my setup.  I have the
> > > latest
> > > firmware 1.28H, running the modem in Class 2.1, with Hylafax 4.1.8.
> >
> > > Jul 27 05:13:02.54: [ 1038]: SESSION BEGIN 00002865 ##########
> > > Jul 27 05:13:02.54: [ 1038]: HylaFAX (tm) Version 4.1.8
> > > Jul 27 05:13:02.54: [ 1038]: <-- [19:AT+FCC=,,,,,,,,0;A\r]
> > > Jul 27 05:13:16.65: [ 1038]: --> [4:+FCO]
> > > Jul 27 05:13:16.65: [ 1038]: ANSWER: FAX CONNECTION  DEVICE
> > > '/dev/ttyS0'
> > > Jul 27 05:13:16.65: [ 1038]: STATE CHANGE: ANSWERING -> RECEIVING
> > > Jul 27 05:13:16.65: [ 1038]: MODEM input buffering enabled
> > > Jul 27 05:13:16.65: [ 1038]: RECV FAX: begin
> > > Jul 27 05:13:16.65: [ 1038]: --> [27:+FTI:"        ### #######"]
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE TSI "### #######"
> > > Jul 27 05:13:16.65: [ 1038]: --> [22:+FCS:0,B,0,2,3,1,0,0,0]
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants 28800 bit/s
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants page width 1728 pixels in
> > > 215 mm
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants unlimited page length
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants 3.85 line/mm
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants 2-D MMR
> > > Jul 27 05:13:16.65: [ 1038]: REMOTE wants T.30 Annex A, ECM
> > > Jul 27 05:13:16.65: [ 1038]: --> [2:OK]
> > > Jul 27 05:13:16.65: [ 1038]: <-- [7:AT+FDR\r]
> > > Jul 27 05:13:21.81: [ 1038]: --> [7:+FHS:A0]
> > > Jul 27 05:13:21.81: [ 1038]: REMOTE HANGUP: Unspecified Phase D error
> > > (codeA0)
> >
> > "Unspecified Phase D error" means that there was an error in phase D
> > (the post-page message portion).  In this case it used V.34 and ECM and
> > we didn't get any page image data at all, so it would indicate that the
> > error was with the partial page signal or with an associated V.34
> > signal.  In any case, we can't tell much from Class 2/2.0/2.1 logs.
> > MultiTech would have to help you if you want to continue with Class 2.1.
> >
> > That said, the problem probably has to do with a firmware flaw in the
> > ECM or V.34-Fax implementations.  So you could switch to Class 2.0 and
> > see if the problem goes away, or you could disable ECM and do likewise.
> >
> > However, my personal recommendation would be for you to upgrade to
> > 4.2.0 and then switch to Class 1.0.  You'll have all of the features
> > that you get in Class 2.1 with that modem, plus you'll have more
> > resolution capability.  Oh, and we'll be able to help you out much more
> > in Class 1/1.0 than we can in Class 2/2.0/2.1.
> >
> > Lee.
> >
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
>   To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*