Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] GVC Fax 14400 V.42bis/MNP5 Modem Problem with Hylafax
On Sun, Jun 13, 2004 at 06:29:06PM -0700, Lee Howard wrote:
> Here are the relevant parts of the post:
> ATI0 RESULT = "OK" RESPONSE = "242"
> ATI1 RESULT = "OK" RESPONSE = "175"
> ATI2 RESULT = "OK" RESPONSE = "OK"
> ATI3 RESULT = "OK" RESPONSE = "E.C. Version : 7.1"
Thank you. I can pretty safely say that that modem is a GVC 14.4
modem.
I'm kind of suspicious of the output, though. For comparison, here's the
output from a GVC 28.8 ATI command set.
ATI0
288
OK
ATI1
173
F1128V/R6 V6.18.13
OK
ATI2
OK
ATI3
E.C. Version: T
ATI4
F1128V/R6 V6.18.13
MODEM CHIP: ROCKWELL RC288DPi
FAX CLASS 1 AND FAX CLASS 2
OK
AT+FCLASS=?
0,1,2
OK
Notice the carriage returns in responses. Dunno if that will matter to
HylaFAX or not. However, it is most definitely class 1 and 2 capable. In
fact all GVC modems that were class 2 capable were class 1 capable.
I'm attaching my config.ttyS1 in hope that it
will help.
-----config.ttyS1
# $Id: gvc-288-2,v 1.3 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a GVC MAXTech 288 RC288DPi-based Class 2 modem.
# Tested with firmware rev KA1131-00.
#
# NB: DCD is toggled at page end during transmits; this can
# cause problems on systems where it's not possible to
# set CLOCAL and also enable RTS/CTS flow control.
#
#
CountryCode: 1
AreaCode: 908
FAXNumber: 1-908-435-3711
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0x08501
SessionTracing: 0x08501
RecvFileMode: 0640
LogFileMode: 0640
DeviceMode: 0660
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b %l"
LocalIdentifier: "Michael Pedersen"
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 1 interface
ModemRate: 19200 # locked for fax sending&receiving
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT\Q0 # disable flow control cmd
ModemSoftFlowCmd: AT\Q1 # software flow control cmd
ModemHardFlowCmd: AT\Q3 # hardware flow control cmd
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
#
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
ModemDialCmd: ATDT%s # T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd: "<19200><xon>" # lock line rate & switch flow control
#
Class2RecvDataTrigger: "\022" # character sent to modem to start recv
#
# These are known to not be implemented on the GVC with the above
# firmware rev. Sending them to the modem does not harm anything,
# but generates an ERROR result that can generate questions from the
# naive--so we disable them here.
#
Class2TBCCmd: none # setup stream mode
Class2PHCTOCmd: none # set phase C timeout parameter
--end config.ttyS1
--
Michael J. Pedersen
My IM IDs: Jabber/pedersen@xxxxxxxxxxxxxx, ICQ/103345809, AIM/pedermj022171
Yahoo/pedermj2002, MSN/pedermj022171@xxxxxxxxxxx
My GnuPG KeyID: 6CB0A96C My Public Key Available At: www.keyserver.net
My GnuPG Key Fingerprint: E8F0 920F EB2F 7FDE DF4E 23CC 2CEB 8E6F 6CB0 A96C
Attachment:
pgp00002.pgp
Description: PGP signature