[hylafax-users] COMREC invalid response received to PPS.

To: "'hylafax-users@xxxxxxxxxxx'" <hylafax-users@xxxxxxxxxxx>
Subject: [hylafax-users] COMREC invalid response received to PPS.
From: Simon Perry <hylafax@xxxxxxxxxxxxxxxx>
Date: Sun, 16 May 2004 13:30:18 +0100

Hi All,

I am having problems sending a fax with two parts, one pdf and one tiff using hylafax 4.2.0 CVS built 02 May. It would appear that hylafax tries to send twice, after receiving an "COMREC invalid response received to PPS" error on the second page of the first try. On the second attempt only the second page is transmitted and that is the only page received. If I send the pages separately no error occurs, two or more page pdf or ps files also cause no error.

What I am wondering here is if the issue lies with Hylafax or the receiver, if I follow hylafax's logic correctly then it is only resending page 2 as the receiver acknowledged that it got page one on the first try. However when the receiver encountered an error it scrapped the whole transmission. I don't know what equipment is on the other end, the receiver is a free online service at www.pumaone.com.

Any insight greatly appreciated.

Simon

May 16 12:56:23.56: [21355]: SESSION BEGIN 000000026 4402008707622312 May 16 12:56:23.56: [21355]: HylaFAX (tm) Version 4.2.0-CVS-02-05-2004 May 16 12:56:23.56: [21355]: SEND FAX: JOB 16 DEST 08707622312 COMMID 000000026 DEVICE '/dev/ttyS0' May 16 12:56:23.56: [21355]: <-- [12:AT+FCLASS=1\r] May 16 12:56:23.72: [21355]: --> [2:OK] May 16 12:56:23.72: [21355]: DIAL 08707622312 May 16 12:56:23.72: [21355]: <-- [16:ATDT08707622312\r] May 16 12:56:36.25: [21355]: --> [7:CONNECT] May 16 12:56:37.91: [21355]: --> [2:OK] May 16 12:56:37.91: [21355]: REMOTE CSI "PUMAONE.COM" May 16 12:56:37.91: [21355]: <-- [9:AT+FRH=3\r] May 16 12:56:37.95: [21355]: --> [7:CONNECT] May 16 12:56:38.20: [21355]: --> [2:OK] May 16 12:56:38.20: [21355]: REMOTE best rate 14400 bit/s May 16 12:56:38.20: [21355]: REMOTE max A4 page width (215 mm) May 16 12:56:38.20: [21355]: REMOTE max unlimited page length May 16 12:56:38.20: [21355]: REMOTE best vres 7.7 line/mm May 16 12:56:38.20: [21355]: REMOTE best format 2-D MR May 16 12:56:38.20: [21355]: REMOTE supports T.30 Annex A, 256-byte ECM May 16 12:56:38.20: [21355]: REMOTE best 0 ms/scanline May 16 12:56:38.20: [21355]: USE 14400 bit/s May 16 12:56:38.20: [21355]: USE error correction mode May 16 12:56:38.20: [21355]: USE 0 ms/scanline May 16 12:56:38.20: [21355]: SEND file "docq/doc20.tif;c1" May 16 12:56:38.20: [21355]: USE A4 page width (215 mm) May 16 12:56:38.20: [21355]: USE unlimited page length May 16 12:56:38.20: [21355]: USE 7.7 line/mm May 16 12:56:38.20: [21355]: USE 2-D MR May 16 12:56:38.20: [21355]: SEND training at v.17 14400 bit/s May 16 12:56:38.20: [21355]: <-- [9:AT+FTH=3\r] May 16 12:56:38.28: [21355]: --> [7:CONNECT] May 16 12:56:38.28: [21355]: <-- data [23] May 16 12:56:38.28: [21355]: <-- data [2] May 16 12:56:40.03: [21355]: --> [7:CONNECT] May 16 12:56:40.03: [21355]: <-- data [7] May 16 12:56:40.03: [21355]: <-- data [2] May 16 12:56:40.36: [21355]: --> [2:OK] May 16 12:56:40.36: [21355]: DELAY 70 ms May 16 12:56:40.43: [21355]: <-- [11:AT+FTM=145\r] May 16 12:56:40.54: [21355]: --> [7:CONNECT] May 16 12:56:40.54: [21355]: <-- data [1024] May 16 12:56:40.54: [21355]: <-- data [1024] May 16 12:56:40.54: [21355]: <-- data [652] May 16 12:56:40.54: [21355]: <-- data [2] May 16 12:56:43.70: [21355]: --> [2:OK] May 16 12:56:43.70: [21355]: <-- [9:AT+FRH=3\r] May 16 12:56:44.08: [21355]: --> [7:CONNECT] May 16 12:56:45.30: [21355]: --> [2:OK] May 16 12:56:45.30: [21355]: TRAINING succeeded May 16 12:56:45.30: [21355]: SEND begin page May 16 12:56:45.30: [21355]: Reading MH-compressed image file May 16 12:56:45.32: [21355]: SEND 2D RTC May 16 12:56:45.32: [21355]: SEND send frame number 0 <snip /> May 16 12:56:45.38: [21355]: SEND send frame number 235 May 16 12:56:45.38: [21355]: DELAY 200 ms May 16 12:56:45.58: [21355]: <-- [11:AT+FTM=146\r] May 16 12:56:45.69: [21355]: --> [7:CONNECT] May 16 12:56:45.69: [21355]: <-- data [1029] <snip /> May 16 12:57:19.70: [21355]: <-- data [1033] May 16 12:57:19.70: [21355]: <-- data [484] May 16 12:57:19.70: [21355]: <-- data [2] May 16 12:57:21.64: [21355]: --> [2:OK] May 16 12:57:21.64: [21355]: DELAY 90 ms May 16 12:57:21.73: [21355]: <-- [9:AT+FTH=3\r] May 16 12:57:21.77: [21355]: --> [7:CONNECT] May 16 12:57:21.77: [21355]: <-- data [7] May 16 12:57:21.77: [21355]: <-- data [2] May 16 12:57:23.09: [21355]: --> [2:OK] May 16 12:57:23.09: [21355]: SEND send PPS (partial page signal) May 16 12:57:23.09: [21355]: SEND send EOM (more documents) May 16 12:57:23.09: [21355]: <-- [9:AT+FRH=3\r] May 16 12:57:23.14: [21355]: --> [7:CONNECT] May 16 12:57:25.24: [21355]: --> [2:OK] May 16 12:57:25.24: [21355]: SEND recv PPR (partial page request) May 16 12:57:25.24: [21355]: DELAY 70 ms May 16 12:57:25.31: [21355]: SEND send frame number 226 May 16 12:57:25.31: [21355]: SEND send frame number 227 May 16 12:57:25.31: [21355]: DELAY 200 ms May 16 12:57:25.51: [21355]: <-- [11:AT+FTM=146\r] May 16 12:57:25.62: [21355]: --> [7:CONNECT] May 16 12:57:25.62: [21355]: <-- data [915] May 16 12:57:25.62: [21355]: <-- data [2] May 16 12:57:26.54: [21355]: --> [2:OK] May 16 12:57:26.54: [21355]: DELAY 90 ms May 16 12:57:26.63: [21355]: <-- [9:AT+FTH=3\r] May 16 12:57:26.67: [21355]: --> [7:CONNECT] May 16 12:57:26.67: [21355]: <-- data [7] May 16 12:57:26.67: [21355]: <-- data [2] May 16 12:57:27.99: [21355]: --> [2:OK] May 16 12:57:27.99: [21355]: SEND send PPS (partial page signal) May 16 12:57:27.99: [21355]: SEND send EOM (more documents) May 16 12:57:27.99: [21355]: <-- [9:AT+FRH=3\r] May 16 12:57:28.04: [21355]: --> [7:CONNECT] May 16 12:57:29.26: [21355]: --> [2:OK] May 16 12:57:29.26: [21355]: SEND recv RNR (receive not ready) May 16 12:57:29.26: [21355]: DELAY 70 ms May 16 12:57:29.33: [21355]: <-- [9:AT+FTH=3\r] May 16 12:57:29.37: [21355]: --> [7:CONNECT] May 16 12:57:29.37: [21355]: <-- data [3] May 16 12:57:29.37: [21355]: <-- data [2] May 16 12:57:30.58: [21355]: --> [2:OK] May 16 12:57:30.58: [21355]: SEND send RR (receive ready) May 16 12:57:30.58: [21355]: <-- [9:AT+FRH=3\r] May 16 12:57:30.69: [21355]: --> [7:CONNECT] May 16 12:57:31.90: [21355]: --> [2:OK] May 16 12:57:31.90: [21355]: SEND recv MCF (message confirmation) May 16 12:57:31.90: [21355]: SEND end page May 16 12:57:31.90: [21355]: SEND FAX (000000026): FROM simon@faxserver TO 08707622312 (page 1 of 2 sent in 0:53) May 16 12:57:31.90: [21355]: SEND FAX (000000026): FROM simon@faxserver TO 08707622312 (docq/doc20.tif;c1 sent in 0:53) May 16 12:57:31.90: [21355]: SEND file "docq/doc21.ps;c1" May 16 12:57:31.90: [21355]: USE A4 page width (215 mm) May 16 12:57:31.90: [21355]: USE unlimited page length May 16 12:57:31.90: [21355]: USE 7.7 line/mm May 16 12:57:31.90: [21355]: USE 2-D MR May 16 12:57:31.90: [21355]: SEND begin page May 16 12:57:31.91: [21355]: Reading MMR-compressed image file May 16 12:57:31.93: [21355]: SEND 2D RTC May 16 12:57:31.93: [21355]: SEND send frame number 0 <snip /> May 16 12:57:31.97: [21355]: SEND send frame number 142 May 16 12:57:31.97: [21355]: DELAY 200 ms May 16 12:57:32.17: [21355]: <-- [11:AT+FTM=146\r] May 16 12:57:32.28: [21355]: --> [7:CONNECT] May 16 12:57:32.28: [21355]: <-- data [1028] <snip /> May 16 12:57:50.64: [21355]: <-- data [1037] May 16 12:57:52.93: [21355]: <-- data [670] May 16 12:57:52.93: [21355]: <-- data [2] May 16 12:57:54.11: [21355]: --> [2:OK] May 16 12:57:54.11: [21355]: DELAY 90 ms May 16 12:57:54.20: [21355]: <-- [9:AT+FTH=3\r] May 16 12:57:54.24: [21355]: --> [7:CONNECT] May 16 12:57:54.24: [21355]: <-- data [7] May 16 12:57:54.24: [21355]: <-- data [2] May 16 12:57:55.56: [21355]: --> [2:OK] May 16 12:57:55.56: [21355]: SEND send PPS (partial page signal) May 16 12:57:55.56: [21355]: SEND send EOP (no more pages or documents) May 16 12:57:55.56: [21355]: <-- [9:AT+FRH=3\r] May 16 12:57:55.60: [21355]: --> [7:CONNECT] May 16 12:57:56.10: [21355]: --> [2:OK] May 16 12:57:56.10: [21355]: SEND recv MCF (message confirmation) May 16 12:57:56.10: [21355]: DELAY 70 ms May 16 12:57:56.17: [21355]: COMREC invalid response received to PPS. May 16 12:57:56.17: [21355]: SEND end page May 16 12:57:56.17: [21355]: <-- [9:AT+FTH=3\r] May 16 12:57:56.21: [21355]: --> [7:CONNECT] May 16 12:57:56.21: [21355]: <-- data [3] May 16 12:57:56.21: [21355]: <-- data [2] May 16 12:57:57.42: [21355]: --> [2:OK] May 16 12:57:57.42: [21355]: <-- [5:ATH0\r] May 16 12:57:57.70: [21355]: --> [2:OK] May 16 12:57:57.70: [21355]: SESSION END

#####################################################################

May 16 12:59:06.97: [21357]: SESSION BEGIN 000000027 4402008707622312 May 16 12:59:06.97: [21357]: HylaFAX (tm) Version 4.2.0-CVS-02-05-2004 May 16 12:59:06.97: [21357]: SEND FAX: JOB 16 DEST 08707622312 COMMID 000000027 DEVICE '/dev/ttyS0' May 16 12:59:06.97: [21357]: <-- [12:AT+FCLASS=1\r] May 16 12:59:07.14: [21357]: --> [2:OK] May 16 12:59:07.14: [21357]: DIAL 08707622312 May 16 12:59:07.14: [21357]: <-- [16:ATDT08707622312\r] May 16 12:59:17.34: [21357]: --> [7:CONNECT] May 16 12:59:19.00: [21357]: --> [2:OK] May 16 12:59:19.00: [21357]: REMOTE CSI "PUMAONE.COM" May 16 12:59:19.00: [21357]: <-- [9:AT+FRH=3\r] May 16 12:59:19.04: [21357]: --> [7:CONNECT] May 16 12:59:19.30: [21357]: --> [2:OK] May 16 12:59:19.30: [21357]: REMOTE best rate 14400 bit/s May 16 12:59:19.30: [21357]: REMOTE max A4 page width (215 mm) May 16 12:59:19.30: [21357]: REMOTE max unlimited page length May 16 12:59:19.30: [21357]: REMOTE best vres 7.7 line/mm May 16 12:59:19.30: [21357]: REMOTE best format 2-D MMR May 16 12:59:19.30: [21357]: REMOTE supports T.30 Annex A, 256-byte ECM May 16 12:59:19.30: [21357]: REMOTE best 0 ms/scanline May 16 12:59:19.30: [21357]: USE 14400 bit/s May 16 12:59:19.30: [21357]: USE error correction mode May 16 12:59:19.30: [21357]: USE 0 ms/scanline May 16 12:59:19.30: [21357]: SEND file "docq/doc21.ps;c1" May 16 12:59:19.30: [21357]: USE A4 page width (215 mm) May 16 12:59:19.30: [21357]: USE unlimited page length May 16 12:59:19.30: [21357]: USE 7.7 line/mm May 16 12:59:19.30: [21357]: USE 2-D MMR May 16 12:59:19.30: [21357]: SEND training at v.17 14400 bit/s May 16 12:59:19.30: [21357]: <-- [9:AT+FTH=3\r] May 16 12:59:19.38: [21357]: --> [7:CONNECT] May 16 12:59:19.38: [21357]: <-- data [23] May 16 12:59:19.38: [21357]: <-- data [2] May 16 12:59:21.12: [21357]: --> [7:CONNECT] May 16 12:59:21.12: [21357]: <-- data [7] May 16 12:59:21.12: [21357]: <-- data [2] May 16 12:59:21.45: [21357]: --> [2:OK] May 16 12:59:21.45: [21357]: DELAY 70 ms May 16 12:59:21.52: [21357]: <-- [11:AT+FTM=145\r] May 16 12:59:21.64: [21357]: --> [7:CONNECT] May 16 12:59:21.64: [21357]: <-- data [1024] May 16 12:59:21.64: [21357]: <-- data [1024] May 16 12:59:21.64: [21357]: <-- data [652] May 16 12:59:21.64: [21357]: <-- data [2] May 16 12:59:24.80: [21357]: --> [2:OK] May 16 12:59:24.80: [21357]: <-- [9:AT+FRH=3\r] May 16 12:59:25.35: [21357]: --> [7:CONNECT] May 16 12:59:26.57: [21357]: --> [2:OK] May 16 12:59:26.57: [21357]: TRAINING succeeded May 16 12:59:26.57: [21357]: SEND begin page May 16 12:59:26.58: [21357]: SEND EOFB May 16 12:59:26.58: [21357]: SEND send frame number 0 <snip /> May 16 12:59:26.60: [21357]: SEND send frame number 105 May 16 12:59:26.60: [21357]: DELAY 200 ms May 16 12:59:26.79: [21357]: <-- [11:AT+FTM=146\r] May 16 12:59:26.91: [21357]: --> [7:CONNECT] May 16 12:59:26.91: [21357]: <-- data [1029] <snip /> May 16 12:59:40.02: [21357]: <-- data [1036] May 16 12:59:40.75: [21357]: <-- data [203] May 16 12:59:40.75: [21357]: <-- data [2] May 16 12:59:43.36: [21357]: --> [2:OK] May 16 12:59:43.36: [21357]: DELAY 90 ms May 16 12:59:43.45: [21357]: <-- [9:AT+FTH=3\r] May 16 12:59:43.50: [21357]: --> [7:CONNECT] May 16 12:59:43.50: [21357]: <-- data [7] May 16 12:59:43.50: [21357]: <-- data [2] May 16 12:59:44.82: [21357]: --> [2:OK] May 16 12:59:44.82: [21357]: SEND send PPS (partial page signal) May 16 12:59:44.82: [21357]: SEND send EOP (no more pages or documents) May 16 12:59:44.82: [21357]: <-- [9:AT+FRH=3\r] May 16 12:59:44.87: [21357]: --> [7:CONNECT] May 16 12:59:46.08: [21357]: --> [2:OK] May 16 12:59:46.08: [21357]: SEND recv RNR (receive not ready) May 16 12:59:46.08: [21357]: DELAY 70 ms May 16 12:59:46.15: [21357]: <-- [9:AT+FTH=3\r] May 16 12:59:46.20: [21357]: --> [7:CONNECT] May 16 12:59:46.20: [21357]: <-- data [3] May 16 12:59:46.20: [21357]: <-- data [2] May 16 12:59:47.40: [21357]: --> [2:OK] May 16 12:59:47.40: [21357]: SEND send RR (receive ready) May 16 12:59:47.40: [21357]: <-- [9:AT+FRH=3\r] May 16 12:59:48.29: [21357]: --> [7:CONNECT] May 16 12:59:49.50: [21357]: --> [2:OK] May 16 12:59:49.50: [21357]: SEND recv MCF (message confirmation) May 16 12:59:49.50: [21357]: SEND end page May 16 12:59:49.50: [21357]: SEND FAX (000000027): FROM simon@faxserver TO 08707622312 (page 2 of 2 sent in 0:30) May 16 12:59:49.50: [21357]: SEND FAX (000000027): FROM simon@faxserver TO 08707622312 (docq/doc21.ps;c1 sent in 0:30) May 16 12:59:49.50: [21357]: <-- [9:AT+FTH=3\r] May 16 12:59:49.58: [21357]: --> [7:CONNECT] May 16 12:59:49.58: [21357]: <-- data [3] May 16 12:59:49.58: [21357]: <-- data [2] May 16 12:59:50.79: [21357]: --> [2:OK] May 16 12:59:50.79: [21357]: <-- [5:ATH0\r] May 16 12:59:51.08: [21357]: --> [2:OK] May 16 12:59:51.08: [21357]: SESSION END

#####################################
/info file

supportsVRes:1
supports2DEncoding:yes
supportsMMR:yes
hasV34Trouble:no
supportsPostScript:no
supportsBatching:yes
calledBefore:yes
maxPageWidth:1728
maxPageLength:65535
maxSignallingRate:"14400"
minScanlineTime:"0ms"
remoteCSI:"PUMAONE.COM"
sendFailures:0
lastSendFailure:"COMREC invalid response received to PPS."
dialFailures:0
&pagingProtocol:"ixo"

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] COMREC invalid response received to PPS.
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] more distinctive ring questions
Next by Date: Re: [hylafax-users] COMREC invalid response received to PPS.
Previous by thread: [hylafax-users] Slackware vs. Hylafax
Next by thread: Re: [hylafax-users] COMREC invalid response received to PPS.
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services