|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Fax gets resent three times
> If they are getting the full page of image data, then the problem
> probably lies with the timing of Class1PPMWaitCmd which defaults to
> AT+FTS=7. You could probably increase this to AT+FTS=9 or AT+FTS=10
> without any ill effects. Maybe that would fix it.
Thanks for all your help, Lee... but, to continue... :)
I went and made the changes above in config/class1 and class1.0. But in the
logs, it looks like it didn't see the change. I looked for all instances of
FTS=7 and changed those as well to 9, but those didn't change either. The
Hylafax FAQ said that a restart is unnecessary... is this not the case?
Below is the most recent log. In this case you'll notice that it isn't an MPS,
but a single page (as far as I can tell), and it also errors.
Thanks again!
.josh
Feb 23 14:43:38.03: [68797]: SESSION BEGIN 00029144 1XXXXXXXXXX
Feb 23 14:43:38.03: [68797]: HylaFAX (tm) Version 4.1.7
Feb 23 14:43:38.03: [68797]: SEND FAX: JOB 16480 DEST 1XXXXXXXXXX COMMID 00029144 DEVICE '/dev/cuaa4'
Feb 23 14:43:38.03: [68797]: DELAY 75 ms
Feb 23 14:43:38.10: [68797]: DELAY 2600 ms
Feb 23 14:43:41.72: [68797]: DELAY 10 ms
Feb 23 14:43:41.74: [68797]: <-- [4:ATZ\r]
Feb 23 14:43:41.75: [68797]: --> [2:OK]
Feb 23 14:43:41.75: [68797]: DELAY 3000 ms
Feb 23 14:43:44.76: [68797]: <-- [5:ATE0\r]
Feb 23 14:43:44.77: [68797]: --> [4:ATE0]
Feb 23 14:43:44.77: [68797]: --> [2:OK]
Feb 23 14:43:44.77: [68797]: <-- [5:ATV1\r]
Feb 23 14:43:44.78: [68797]: --> [2:OK]
Feb 23 14:43:44.78: [68797]: <-- [5:ATQ0\r]
Feb 23 14:43:44.79: [68797]: --> [2:OK]
Feb 23 14:43:44.79: [68797]: <-- [7:ATS0=0\r]
Feb 23 14:43:44.80: [68797]: --> [2:OK]
Feb 23 14:43:44.80: [68797]: <-- [7:ATS8=2\r]
Feb 23 14:43:44.81: [68797]: --> [2:OK]
Feb 23 14:43:44.81: [68797]: <-- [8:ATS7=60\r]
Feb 23 14:43:44.82: [68797]: --> [2:OK]
Feb 23 14:43:44.82: [68797]: <-- [6:AT&K3\r]
Feb 23 14:43:44.83: [68797]: --> [2:OK]
Feb 23 14:43:44.83: [68797]: <-- [6:AT&D2\r]
Feb 23 14:43:44.84: [68797]: --> [2:OK]
Feb 23 14:43:44.84: [68797]: <-- [6:AT&C1\r]
Feb 23 14:43:44.85: [68797]: --> [2:OK]
Feb 23 14:43:44.85: [68797]: <-- [12:AT+FCLASS=1\r]
Feb 23 14:43:44.86: [68797]: --> [2:OK]
Feb 23 14:43:44.86: [68797]: <-- [5:ATM0\r]
Feb 23 14:43:44.87: [68797]: --> [2:OK]
Feb 23 14:43:44.87: [68797]: <-- [12:AT+FCLASS=1\r]
Feb 23 14:43:44.98: [68797]: --> [2:OK]
Feb 23 14:43:44.98: [68797]: DIAL 1XXXXXXXXXX
Feb 23 14:43:44.98: [68797]: <-- [16:ATDT1XXXXXXXXXX\r]
Feb 23 14:44:22.14: [68797]: --> [7:CONNECT]
Feb 23 14:44:23.20: [68797]: --> [2:OK]
Feb 23 14:44:23.20: [68797]: REMOTE NSF "AD 00 36 A0 00 00 00 00 38"
Feb 23 14:44:23.20: [68797]: NSF remote fax equipment: HP
Feb 23 14:44:23.20: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:23.22: [68797]: --> [7:CONNECT]
Feb 23 14:44:23.92: [68797]: --> [2:OK]
Feb 23 14:44:23.92: [68797]: REMOTE CSI "XXXXXXXXXX"
Feb 23 14:44:23.92: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:23.94: [68797]: --> [7:CONNECT]
Feb 23 14:44:24.35: [68797]: --> [2:OK]
Feb 23 14:44:24.35: [68797]: REMOTE best rate 33600 bit/s
Feb 23 14:44:24.35: [68797]: REMOTE max page width 1728 pixels in 215 mm
Feb 23 14:44:24.35: [68797]: REMOTE max unlimited page length
Feb 23 14:44:24.35: [68797]: REMOTE best vres 7.7 line/mm
Feb 23 14:44:24.35: [68797]: REMOTE best format 2-D MMR
Feb 23 14:44:24.35: [68797]: REMOTE supports T.30 Annex A, ECM
Feb 23 14:44:24.35: [68797]: REMOTE best 0 ms/scanline
Feb 23 14:44:24.35: [68797]: USE 14400 bit/s
Feb 23 14:44:24.35: [68797]: USE 0 ms/scanline
Feb 23 14:44:24.35: [68797]: SEND file "docq/doc16493.ps;70"
Feb 23 14:44:24.35: [68797]: USE page width 1728 pixels in 215 mm
Feb 23 14:44:24.35: [68797]: USE unlimited page length
Feb 23 14:44:24.35: [68797]: USE 3.85 line/mm
Feb 23 14:44:24.35: [68797]: USE 2-D MR
Feb 23 14:44:24.35: [68797]: SEND training at v.17 14400 bit/s
Feb 23 14:44:24.35: [68797]: <-- [9:AT+FTH=3\r]
Feb 23 14:44:24.54: [68797]: --> [7:CONNECT]
Feb 23 14:44:24.54: [68797]: <-- data [23]
Feb 23 14:44:24.54: [68797]: <-- data [2]
Feb 23 14:44:24.56: [68797]: --> [7:CONNECT]
Feb 23 14:44:24.56: [68797]: <-- data [6]
Feb 23 14:44:24.56: [68797]: <-- data [2]
Feb 23 14:44:26.52: [68797]: --> [2:OK]
Feb 23 14:44:26.52: [68797]: <-- [9:AT+FTS=7\r]
Feb 23 14:44:26.60: [68797]: --> [2:OK]
Feb 23 14:44:26.60: [68797]: <-- [11:AT+FTM=145\r]
Feb 23 14:44:28.08: [68797]: --> [7:CONNECT]
Feb 23 14:44:28.08: [68797]: <-- data [1024]
Feb 23 14:44:28.08: [68797]: <-- data [1024]
Feb 23 14:44:28.08: [68797]: <-- data [652]
Feb 23 14:44:28.80: [68797]: <-- data [2]
Feb 23 14:44:29.61: [68797]: --> [2:OK]
Feb 23 14:44:29.61: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:30.05: [68797]: --> [7:CONNECT]
Feb 23 14:44:31.06: [68797]: --> [2:OK]
Feb 23 14:44:31.06: [68797]: TRAINING succeeded
Feb 23 14:44:31.06: [68797]: DELAY 75 ms
Feb 23 14:44:31.14: [68797]: <-- [11:AT+FTM=146\r]
Feb 23 14:44:31.40: [68797]: --> [7:CONNECT]
Feb 23 14:44:31.40: [68797]: SEND begin page
Feb 23 14:44:31.40: [68797]: <-- data [1027]
Feb 23 14:44:31.40: [68797]: <-- data [1032]
Feb 23 14:44:31.40: [68797]: <-- data [1030]
Feb 23 14:44:32.12: [68797]: <-- data [1032]
Feb 23 14:44:32.12: [68797]: <-- data [1035]
Feb 23 14:44:32.98: [68797]: <-- data [1035]
Feb 23 14:44:32.99: [68797]: <-- data [1035]
Feb 23 14:44:33.85: [68797]: <-- data [1035]
Feb 23 14:44:33.85: [68797]: <-- data [1036]
Feb 23 14:44:34.71: [68797]: <-- data [1035]
Feb 23 14:44:34.71: [68797]: <-- data [955]
Feb 23 14:44:35.57: [68797]: SENT 11186 bytes of data
Feb 23 14:44:35.57: [68797]: SEND 2D RTC
Feb 23 14:44:35.57: [68797]: <-- data [30]
Feb 23 14:44:35.57: [68797]: <-- data [2]
Feb 23 14:44:35.57: [68797]: SEND end page
Feb 23 14:44:37.66: [68797]: --> [2:OK]
Feb 23 14:44:37.66: [68797]: <-- [9:AT+FTS=9\r]
Feb 23 14:44:37.76: [68797]: --> [2:OK]
Feb 23 14:44:37.76: [68797]: SEND send EOP (no more pages or documents)
Feb 23 14:44:37.76: [68797]: <-- [9:AT+FTH=3\r]
Feb 23 14:44:37.91: [68797]: --> [7:CONNECT]
Feb 23 14:44:37.91: [68797]: <-- data [3]
Feb 23 14:44:37.91: [68797]: <-- data [2]
Feb 23 14:44:39.09: [68797]: --> [2:OK]
Feb 23 14:44:39.09: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:39.21: [68797]: --> [10:NO CARRIER]
Feb 23 14:44:39.21: [68797]: MODEM No carrier
Feb 23 14:44:39.21: [68797]: SEND send EOP (no more pages or documents)
Feb 23 14:44:39.21: [68797]: <-- [9:AT+FTH=3\r]
Feb 23 14:44:39.40: [68797]: --> [7:CONNECT]
Feb 23 14:44:39.40: [68797]: <-- data [3]
Feb 23 14:44:39.40: [68797]: <-- data [2]
Feb 23 14:44:40.58: [68797]: --> [2:OK]
Feb 23 14:44:40.58: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:40.81: [68797]: --> [10:NO CARRIER]
Feb 23 14:44:40.81: [68797]: MODEM No carrier
Feb 23 14:44:40.81: [68797]: SEND send EOP (no more pages or documents)
Feb 23 14:44:40.81: [68797]: <-- [9:AT+FTH=3\r]
Feb 23 14:44:41.00: [68797]: --> [7:CONNECT]
Feb 23 14:44:41.00: [68797]: <-- data [3]
Feb 23 14:44:41.00: [68797]: <-- data [2]
Feb 23 14:44:42.18: [68797]: --> [2:OK]
Feb 23 14:44:42.18: [68797]: <-- [9:AT+FRH=3\r]
Feb 23 14:44:42.41: [68797]: --> [10:NO CARRIER]
Feb 23 14:44:42.41: [68797]: MODEM No carrier
Feb 23 14:44:42.41: [68797]: No response to MPS or EOP repeated 3 tries
Feb 23 14:44:42.41: [68797]: SEND: No response to MPS or EOP repeated 3 tries; Giving up after 3 attempts to send same page "docq/doc16493.ps;70", dirnum 0
Feb 23 14:44:42.41: [68797]: <-- [9:AT+FTH=3\r]
Feb 23 14:44:42.60: [68797]: --> [7:CONNECT]
Feb 23 14:44:42.60: [68797]: <-- data [3]
Feb 23 14:44:42.60: [68797]: <-- data [2]
Feb 23 14:44:43.78: [68797]: --> [2:OK]
Feb 23 14:44:43.78: [68797]: <-- [5:ATH0\r]
Feb 23 14:44:48.78: [68797]: MODEM <Timeout>
Feb 23 14:44:48.78: [68797]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
