[hylafax-users] No response to MPS or EOP repeated 3 tries

To: HylaFax Mailing List <hylafax-users@xxxxxxxxxxx>
Subject: [hylafax-users] No response to MPS or EOP repeated 3 tries
From: "Priya" <priya@xxxxxxxxxxx>
Date: Fri, 10 Oct 2003 17:19:14 +0530
Hi,

I have problem while sending fax to certain Fax machine, Send fax fails due 
No response to MPS or EOP repeated 3 tries.

I searched the mailing archives i got a solution

** Start

You can cure the symptom by changing the last FALSE to a TRUE in the
following, but I doubt that the remote machine will continue sensibly
if it hasn't responded to more pages same document, so you might want
to make this conditional on whether more pages same or end of procedure
is being sent.

It may be necessary to fake an MCF frame.

I suspect, though, that most serious developers are using Class 2 or 2.0
modems.

Class1Modem::sendPPM(u_int ppm, HDLCFrame& mcf, fxStr& emsg)
{
    for (int t = 0; t < 3; t++) {
        tracePPM("SEND send", ppm);
        if (transmitFrame(ppm|FCF_SNDR) && recvFrame(mcf, conf.t4Timer))
            return (TRUE);
        if (abortRequested())
            return (FALSE);
    }
    emsg = "No response to MPS or EOP repeated 3 tries";
    return (FALSE);
}
** Stop

But none works out.

My Log File 

** Start
Oct 10 17:02:57.08: [19887]: SESSION BEGIN 00000088 9104424365979
Oct 10 17:02:57.08: [19887]: HylaFAX (tm) Version 4.1.7
Oct 10 17:02:57.08: [19887]: SEND FAX: JOB 18 DEST 24365979 COMMID 00000088
DEVICE '/dev/ttyW3'
Oct 10 17:02:57.08: [19887]: MODEM set DTR OFF
Oct 10 17:02:57.08: [19887]: DELAY 75 ms
Oct 10 17:02:57.16: [19887]: MODEM set DTR ON
Oct 10 17:02:57.16: [19887]: DELAY 2600 ms
Oct 10 17:03:00.78: [19887]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Oct 10 17:03:00.78: [19887]: DELAY 10 ms
Oct 10 17:03:00.79: [19887]: MODEM flush i/o
Oct 10 17:03:00.79: [19887]: <-- [4:ATZ\r]
Oct 10 17:03:00.88: [19887]: --> [2:OK]
Oct 10 17:03:00.88: [19887]: DELAY 3000 ms
Oct 10 17:03:03.88: [19887]: <-- [5:ATE0\r]
Oct 10 17:03:03.89: [19887]: --> [4:ATE0]
Oct 10 17:03:03.89: [19887]: --> [2:OK]
Oct 10 17:03:03.89: [19887]: <-- [5:ATV1\r]
Oct 10 17:03:03.90: [19887]: --> [2:OK]
Oct 10 17:03:03.90: [19887]: <-- [5:ATQ0\r]
Oct 10 17:03:03.91: [19887]: --> [2:OK]
Oct 10 17:03:03.91: [19887]: <-- [7:ATS0=0\r]
Oct 10 17:03:03.92: [19887]: --> [2:OK]
Oct 10 17:03:03.92: [19887]: <-- [7:ATS8=2\r]
Oct 10 17:03:03.93: [19887]: --> [2:OK]
Oct 10 17:03:03.93: [19887]: <-- [8:ATS7=60\r]
Oct 10 17:03:03.94: [19887]: --> [2:OK]
Oct 10 17:03:03.94: [19887]: <-- [6:AT&K3\r]
Oct 10 17:03:03.95: [19887]: --> [2:OK]
Oct 10 17:03:03.95: [19887]: <-- [6:AT&D2\r]
Oct 10 17:03:03.96: [19887]: --> [2:OK]
Oct 10 17:03:03.96: [19887]: <-- [6:AT&C1\r]
Oct 10 17:03:03.97: [19887]: --> [2:OK]
Oct 10 17:03:03.97: [19887]: <-- [12:AT+FCLASS=1\r]
Oct 10 17:03:03.99: [19887]: --> [2:OK]
Oct 10 17:03:03.99: [19887]: <-- [5:ATM0\r]
Oct 10 17:03:04.00: [19887]: --> [2:OK]
Oct 10 17:03:04.00: [19887]: MODEM input buffering enabled
Oct 10 17:03:04.00: [19887]: <-- [12:AT+FCLASS=1\r]
Oct 10 17:03:04.12: [19887]: --> [2:OK]
Oct 10 17:03:04.12: [19887]: DIAL 24365979
Oct 10 17:03:04.12: [19887]: <-- [15:ATX3DT24365979\r]
Oct 10 17:03:27.79: [19887]: --> [7:CONNECT]
Oct 10 17:03:27.79: [19887]: MODEM input buffering disabled
Oct 10 17:03:29.53: [19887]: --> HDLC<41:FF C0 04 00 00 88 01 00 51 92 08 42
12 A2 32 04 22 42 04 72 A2 EA 04 22 A2 32 12 00 F2 00 01 01 1B 61 80 80 80 80
00 6D AD>
Oct 10 17:03:29.54: [19887]: --> [2:OK]
Oct 10 17:03:29.54: [19887]: REMOTE NSF "00 00 11 80 00 8A 49 10 42 48 45 4C
20 44 42 20 4E 45 57 20 44 45 4C 48 00 4F 00 80 80 D8 86 01 01 01 01 00 B6"
Oct 10 17:03:29.54: [19887]: NSF remote fax equipment: Canon Laser Class 9000
Series
Oct 10 17:03:29.54: [19887]: NSF remote station ID: "BHEL DB NEW DELH"
Oct 10 17:03:29.54: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:03:29.56: [19887]: --> [7:CONNECT]
Oct 10 17:03:30.23: [19887]: --> HDLC<25:FF C0 02 9C EC 9C AC 6C CC 2C 4C 04
8C 8C 04 8C 9C 04 04 04 04 04 04 D8 A8>
Oct 10 17:03:30.23: [19887]: --> [2:OK]
Oct 10 17:03:30.23: [19887]: REMOTE CSI "91 11 24365979"
Oct 10 17:03:30.23: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:03:30.25: [19887]: --> [7:CONNECT]
Oct 10 17:03:30.49: [19887]: --> HDLC<9:FF C8 01 00 77 15 22 17 5D>
Oct 10 17:03:30.50: [19887]: --> [2:OK]
Oct 10 17:03:30.50: [19887]: REMOTE best rate 14400 bit/s
Oct 10 17:03:30.50: [19887]: REMOTE max page width 1728 pixels in 215 mm
Oct 10 17:03:30.50: [19887]: REMOTE max unlimited page length
Oct 10 17:03:30.50: [19887]: REMOTE best vres 7.7 line/mm
Oct 10 17:03:30.50: [19887]: REMOTE best format 2-D MMR
Oct 10 17:03:30.50: [19887]: REMOTE supports T.30 Annex A, ECM
Oct 10 17:03:30.50: [19887]: REMOTE best 10 ms/scanline
Oct 10 17:03:30.50: [19887]: USE 14400 bit/s
Oct 10 17:03:30.50: [19887]: USE 10 ms/scanline
Oct 10 17:03:30.50: [19887]: SEND file "docq/doc19.ps;40"
Oct 10 17:03:30.89: [19887]: USE page width 1728 pixels in 215 mm
Oct 10 17:03:30.89: [19887]: USE unlimited page length
Oct 10 17:03:30.89: [19887]: USE 3.85 line/mm
Oct 10 17:03:30.89: [19887]: USE 2-D MR
Oct 10 17:03:30.89: [19887]: SEND training at v.17 14400 bit/s
Oct 10 17:03:30.89: [19887]: <-- [9:AT+FTH=3\r]
Oct 10 17:03:30.94: [19887]: --> [7:CONNECT]
Oct 10 17:03:30.94: [19887]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Oct 10 17:03:30.94: [19887]: <-- data [23]
Oct 10 17:03:30.94: [19887]: <-- data [2]
Oct 10 17:03:32.72: [19887]: --> [7:CONNECT]
Oct 10 17:03:32.72: [19887]: <-- HDLC<6:FF C8 C1 00 45 14>
Oct 10 17:03:32.72: [19887]: <-- data [6]
Oct 10 17:03:32.72: [19887]: <-- data [2]
Oct 10 17:03:33.15: [19887]: --> [2:OK]
Oct 10 17:03:33.15: [19887]: <-- [9:AT+FTS=7\r]
Oct 10 17:03:33.24: [19887]: --> [2:OK]
Oct 10 17:03:33.24: [19887]: <-- [11:AT+FTM=145\r]
Oct 10 17:03:33.28: [19887]: --> [7:CONNECT]
Oct 10 17:03:33.28: [19887]: <-- data [1024]
Oct 10 17:03:33.28: [19887]: <-- data [1024]
Oct 10 17:03:33.28: [19887]: <-- data [652]
Oct 10 17:03:33.28: [19887]: <-- data [2]
Oct 10 17:03:36.39: [19887]: --> [2:OK]
Oct 10 17:03:36.39: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:03:36.75: [19887]: --> [7:CONNECT]
Oct 10 17:03:37.66: [19887]: --> HDLC<5:FF C8 21 57 BE>
Oct 10 17:03:37.66: [19887]: --> [2:OK]
Oct 10 17:03:37.66: [19887]: DELAY 75 ms
Oct 10 17:03:37.74: [19887]: <-- [11:AT+FTM=146\r]
Oct 10 17:03:37.78: [19887]: --> [7:CONNECT]
Oct 10 17:03:37.78: [19887]: SEND begin page
Oct 10 17:03:37.80: [19887]: <-- data [1024]
Oct 10 17:03:37.80: [19887]: <-- data [1026]
Oct 10 17:03:37.80: [19887]: <-- data [1039]
Oct 10 17:03:37.80: [19887]: <-- data [1038]
Oct 10 17:03:39.94: [19887]: <-- data [1039]
Oct 10 17:03:39.94: [19887]: <-- data [1034]
Oct 10 17:03:39.94: [19887]: <-- data [1039]
Oct 10 17:03:39.94: [19887]: <-- data [1038]
Oct 10 17:03:42.07: [19887]: <-- data [1038]
Oct 10 17:03:42.07: [19887]: <-- data [1037]
Oct 10 17:03:42.07: [19887]: <-- data [1039]
Oct 10 17:03:42.07: [19887]: <-- data [1039]
Oct 10 17:03:44.21: [19887]: <-- data [1038]
Oct 10 17:03:44.21: [19887]: <-- data [1038]
Oct 10 17:03:44.21: [19887]: <-- data [1038]
Oct 10 17:03:44.21: [19887]: <-- data [1035]
Oct 10 17:03:46.57: [19887]: <-- data [1040]
Oct 10 17:03:46.57: [19887]: <-- data [1037]
Oct 10 17:03:46.57: [19887]: <-- data [1039]
Oct 10 17:03:46.57: [19887]: <-- data [1035]
Oct 10 17:03:48.71: [19887]: <-- data [141]
Oct 10 17:03:48.71: [19887]: SENT 20618 bytes of data
Oct 10 17:03:48.71: [19887]: <-- data [1041]
Oct 10 17:03:48.71: [19887]: <-- data [1037]
Oct 10 17:03:48.71: [19887]: <-- data [1040]
Oct 10 17:03:48.71: [19887]: <-- data [17]
Oct 10 17:03:48.71: [19887]: SENT 3089 bytes of data
Oct 10 17:03:48.71: [19887]: SEND 2D RTC
Oct 10 17:03:48.71: [19887]: <-- data [30]
Oct 10 17:03:48.71: [19887]: <-- data [2]
Oct 10 17:03:48.71: [19887]: SEND end page
Oct 10 17:03:51.33: [19887]: --> [2:OK]
Oct 10 17:03:51.33: [19887]: <-- [9:AT+FTS=9\r]
Oct 10 17:03:51.44: [19887]: --> [2:OK]
Oct 10 17:03:51.44: [19887]: SEND send EOP (no more pages or documents)
Oct 10 17:03:51.44: [19887]: <-- [9:AT+FTH=3\r]
Oct 10 17:03:51.48: [19887]: --> [7:CONNECT]
Oct 10 17:03:51.48: [19887]: <-- HDLC<3:FF C8 F4>
Oct 10 17:03:51.48: [19887]: <-- data [3]
Oct 10 17:03:51.48: [19887]: <-- data [2]
Oct 10 17:03:52.80: [19887]: --> [2:OK]
Oct 10 17:03:52.80: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:03:55.90: [19887]: --> [0:]
Oct 10 17:03:55.90: [19887]: MODEM <Empty line>
Oct 10 17:03:55.90: [19887]: MODEM TIMEOUT: waiting for v.21 carrier
Oct 10 17:03:55.90: [19887]: <-- data [1]
Oct 10 17:03:55.95: [19887]: --> [2:OK]
Oct 10 17:03:55.95: [19887]: SEND send EOP (no more pages or documents)
Oct 10 17:03:55.95: [19887]: <-- [9:AT+FTH=3\r]
Oct 10 17:03:55.99: [19887]: --> [7:CONNECT]
Oct 10 17:03:55.99: [19887]: <-- HDLC<3:FF C8 F4>
Oct 10 17:03:55.99: [19887]: <-- data [3]
Oct 10 17:03:55.99: [19887]: <-- data [2]
Oct 10 17:03:57.31: [19887]: --> [2:OK]
Oct 10 17:03:57.31: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:04:00.41: [19887]: --> [0:]
Oct 10 17:04:00.41: [19887]: MODEM <Empty line>
Oct 10 17:04:00.41: [19887]: MODEM TIMEOUT: waiting for v.21 carrier
Oct 10 17:04:00.41: [19887]: <-- data [1]
Oct 10 17:04:00.47: [19887]: --> [2:OK]
ct 10 17:04:00.47: [19887]: SEND send EOP (no more pages or documents)
Oct 10 17:04:00.47: [19887]: <-- [9:AT+FTH=3\r]
Oct 10 17:04:00.51: [19887]: --> [7:CONNECT]
Oct 10 17:04:00.51: [19887]: <-- HDLC<3:FF C8 F4>
Oct 10 17:04:00.51: [19887]: <-- data [3]
Oct 10 17:04:00.51: [19887]: <-- data [2]
Oct 10 17:04:01.83: [19887]: --> [2:OK]
Oct 10 17:04:01.83: [19887]: <-- [9:AT+FRH=3\r]
Oct 10 17:04:04.93: [19887]: --> [0:]
Oct 10 17:04:04.93: [19887]: MODEM <Empty line>
Oct 10 17:04:04.93: [19887]: MODEM TIMEOUT: waiting for v.21 carrier
Oct 10 17:04:04.93: [19887]: <-- data [1]
Oct 10 17:04:04.99: [19887]: --> [2:OK]
Oct 10 17:04:04.99: [19887]: No response to MPS or EOP repeated 3 tries
Oct 10 17:04:04.99: [19887]: SEND: No response to MPS or EOP repeated 3 tries;
Giving up after 3 attempts to send same page "docq/doc19.ps;40", dirnum 0
Oct 10 17:04:04.99: [19887]: <-- [9:AT+FTH=3\r]
Oct 10 17:04:05.03: [19887]: --> [7:CONNECT]
Oct 10 17:04:05.03: [19887]: <-- HDLC<3:FF C8 DF>
Oct 10 17:04:05.03: [19887]: <-- data [3]
Oct 10 17:04:05.03: [19887]: <-- data [2]
Oct 10 17:04:06.35: [19887]: --> [2:OK]
Oct 10 17:04:06.35: [19887]: MODEM input buffering enabled
Oct 10 17:04:06.35: [19887]: <-- [5:ATH0\r]
Oct 10 17:04:07.10: [19887]: --> [2:OK]
Oct 10 17:04:07.10: [19887]: MODEM set DTR OFF
Oct 10 17:04:07.11: [19887]: SESSION END

** End


Can anyone help me out ????

Thanks in advance !!!!


With Regards,

Priya


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
  - From: An Intrepid HylaFax User
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] Web/Fax Gateway
Next by Date: Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
Previous by thread: Re: [hylafax-users] fax2ps conversions
Next by thread: Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services