[hylafax-users] Fw: Class1.0 modem can't receive fax but it can send fax

Hello, everybody,
I come from china and my english is very poor! Excuse me!
Now I have some problems , I want to ask everyone.
My system environment is :
    OS: RedHat Linux 9.0
    have two fax modems : one is class2.0 ,another is class1.0 modem
    Installed Version: Hylafax-4.1.7.tar.gz and I installed with : "
      tar zxvf hylafax-4.1.7.tar.gz
      cd hylafax-4.1.7
      ./configure
      make
      make install
      faxsetup
    then with default configure except based information.
I with the same direcotry for two modems, but have two line and telephone. (i.e: have two
different telephone numbers). modem 1st with ttyS0 , modem 2nd with ttyS1 . and
configure is:
1, The contents of /var/spool/hylafax/etc/config.ttyS0
#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            86
AreaCode:               XXX
FAXNumber:            +86.XXX.XXXXXXX
LongDistancePrefix:      0
InternationalPrefix:       00
DialStringRules:         etc/dialrules
ServerTracing:           1
SessionTracing:          11
RecvFileMode:          0644
LogFileMode:           0644
DeviceMode:            0644
RingsBeforeAnswer:      1
SpeakerVolume:         medium
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:          TcFax1
TagLineFont:           etc/lutRS18.pcf
TagLineFormat:         "From %%l|%c|Page %%P of %%T"
MaxRecvPages:          25
ModemType:              Class2.0        # use this to supply a hint
#ModemRate:             19200           # max rate for DCE-DTE communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD reflects carrier (or not)
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2PTSQueryCmd:      AT+FPS?         # set post-page status query command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command

2. The contents of /var/spool/hylafax/etc/config.ttyS1
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            86
AreaCode:               XXX
FAXNumber:              +86.XXX.XXXXXXXx
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0644
RingsBeforeAnswer:      1
SpeakerVolume:          medium
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        TcFax2
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before EOP
Class1MsgRecvHackCmd:   ""      # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF & response
Class1SendMsgDelay:     75              # 75ms delay after training
Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and trans
Class1TrainingRecovery: 1500            # 1.5sec delay after training failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

and when I run " faxstat " , it's shown:
[root@webserver etc]# faxstat
HylaFAX scheduler on webserver: Running
Modem ttyS0 (+86.XXX.XXXXXXX): Running and idle
Modem ttyS1 (+86.XXX.XXXXXXX): Running and idle
[root@webserver etc]#

Now modem 1st(class2.0) can work normaly, but modem(class1.0) 2nd can't receive fax and
it cant send fax out normaly. The error( /var/spool/hylafax/log/c00000001)is:[NO CARRIER]
Why ? help me!
Anticipating your brainchild.
Best Regards,
Rubil

[hylafax-users] Fw: Class1.0 modem can't receive fax but it can send fax, why? help!