|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Some users don't get all scan lines
On 2003.08.30 16:59 Michael Evans wrote:
> I started with newly extracted sources from the 4.1.7 tarball.
Unfortunately, you may need to use CVS and not 4.1.7... I can't say for
certain.
> I first applied the patch to support Class1TMConnectDelay (428); then
> I applied the patch for Class1ValidateV21Frames (442); and finally,
> the last patch on the bugzilla page for ECM support (461). When this
> last was applied, the patch command said there were 3 HUNKs that
> failed.
Due to the fact that the patch applies against CVS and not 4.1.7.
> One was in a modem config file I'm not using, but 2 were in
> /faxd/Class1Recv.c++, so I fixed this file manually. (Were other
> patches on the bugzilla page for bug 232 supposed to be applied as
> well?)
No, you only use the last patch.
> Obviously I'm going to delete this build and go back to 4.1.7, but at
> this point I'm thinking seriously about some hardware other than the
> currently installed Zoom 2920.
I've used a Zoom 2920 with no problems, as well as Zoom's USB version
of that modem line, also without problems.
> Aug 30 15:17:28.30: [28881]: SEND training at v.17 14400 bit/s
> Aug 30 15:17:28.30: [28881]: <-- [9:AT+FTH=3\r]
> Aug 30 15:17:29.16: [28881]: --> [7:CONNECT]
> Aug 30 15:17:29.16: [28881]: <-- data [23]
> Aug 30 15:17:29.16: [28881]: <-- data [2]
> Aug 30 15:17:29.17: [28881]: --> [7:CONNECT]
> Aug 30 15:17:29.17: [28881]: <-- data [6]
> Aug 30 15:17:29.17: [28881]: <-- data [2]
> Aug 30 15:17:30.26: [28881]: --> [2:OK]
> Aug 30 15:17:30.26: [28881]: <-- [9:AT+FTS=7\r]
> Aug 30 15:17:30.32: [28881]: --> [2:OK]
> Aug 30 15:17:30.32: [28881]: <-- [11:AT+FTM=145\r]
> Aug 30 15:17:30.33: [28881]: --> [7:CONNECT]
> Aug 30 15:17:30.33: [28881]: DELAY 400 ms
> Aug 30 15:17:30.73: [28881]: <-- data [1024]
> Aug 30 15:17:30.73: [28881]: <-- data [1024]
> Aug 30 15:17:30.73: [28881]: <-- data [652]
> Aug 30 15:17:30.73: [28881]: <-- data [2]
> Aug 30 15:17:33.46: [28881]: --> [2:OK]
> Aug 30 15:17:33.46: [28881]: <-- [9:AT+FRH=3\r]
> Aug 30 15:17:33.81: [28881]: --> [7:CONNECT]
> Aug 30 15:17:34.98: [28881]: --> [2:OK]
> Aug 30 15:17:34.98: [28881]: TRAINING succeeded
Notice that this time we got a successful training at 14400. So there
is some improvement.
As for the "no response to PPS sent 3 times" error that you're getting,
I'd prefer to wait until after you try CVS before trying to figure out
that problem... since something in CVS may make a difference here. (I
can't say *what* off-hand, though.)
Lee.
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
