[hylafax-users] why hylafax send 0 pages?

[so-8859-1?Q?caescvs?caescvs@libero.it]

Hi, 

I'm installing hylafax hylafax-4.1.6-1rh8 package on my RedHat 8.0 server. 

I can recive Fax, and i can receve it in e.mail. IT is ok... 

I installed WHFC to Windows client to send fax.

When I send fax, the "hylafax server" accept and queque it. the destination fax ring, but recive 0 pages. 

I controlled .ps files (docs/*.ps), and it was ok (i see the fax). this is the log:

MAIL REPORT:
--------------------------------------------------------------------

Your facsimile job to 042141623 was completed successfully.

Pages: 0
Quality: Normal
Page Width: 194 (mm)
Page Length: 281 (mm)
Signal Rate: 9600 bit/s
Data Format: 2-D MMR
Submitted From: 10.0.0.201
JobID: 7
GroupID: 7
CommID: c00000019

Processing time was 0:51.

*************************************************
C00000019 log file
--------------------------------------------------------------------
lug 03 12:39:48.39: [ 1907]: SESSION BEGIN 00000019 00390421042141623
lug 03 12:39:48.39: [ 1907]: HylaFAX (tm) Version 4.1.6
lug 03 12:39:48.39: [ 1907]: SEND FAX: JOB 7 DEST xxxxx1623 COMMID 00000019 DEVICE '/dev/ttyS0'
lug 03 12:39:48.39: [ 1907]: DELAY 75 ms
lug 03 12:39:48.47: [ 1907]: DELAY 2600 ms
lug 03 12:39:52.07: [ 1907]: DELAY 10 ms
lug 03 12:39:52.08: [ 1907]: <-- [4:ATZ\r]
lug 03 12:39:52.25: [ 1907]: --> [2:OK]
lug 03 12:39:52.25: [ 1907]: DELAY 3000 ms
lug 03 12:39:55.25: [ 1907]: <-- [5:ATE0\r]
lug 03 12:39:55.35: [ 1907]: --> [4:ATE0]
lug 03 12:39:55.35: [ 1907]: --> [2:OK]
lug 03 12:39:55.35: [ 1907]: <-- [5:ATV1\r]
lug 03 12:39:55.45: [ 1907]: --> [2:OK]
lug 03 12:39:55.45: [ 1907]: <-- [7:ATQ0X3\r]
lug 03 12:39:55.56: [ 1907]: --> [2:OK]
lug 03 12:39:55.56: [ 1907]: <-- [7:ATS0=0\r]
lug 03 12:39:55.67: [ 1907]: --> [2:OK]
lug 03 12:39:55.67: [ 1907]: <-- [7:ATS8=2\r]
lug 03 12:39:55.77: [ 1907]: --> [2:OK]
lug 03 12:39:55.77: [ 1907]: <-- [8:ATS7=60\r]
lug 03 12:39:55.88: [ 1907]: --> [2:OK]
lug 03 12:39:55.88: [ 1907]: <-- [12:AT+FCLASS=1\r]
lug 03 12:39:55.99: [ 1907]: --> [2:OK]
lug 03 12:39:55.99: [ 1907]: <-- [7:ATL1M1\r]
lug 03 12:39:56.09: [ 1907]: --> [2:OK]
lug 03 12:39:56.09: [ 1907]: <-- [12:AT+FCLASS=1\r]
lug 03 12:39:56.30: [ 1907]: --> [2:OK]
lug 03 12:39:56.30: [ 1907]: DIAL 042141623
lug 03 12:39:56.30: [ 1907]: <-- [14:ATDPxxxxx1623\r]
lug 03 12:40:23.63: [ 1907]: --> [7:CONNECT]
lug 03 12:40:25.25: [ 1907]: --> [2:OK]
lug 03 12:40:25.25: [ 1907]: REMOTE NSF "59 01 02 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 C4 00 12 9E"
lug 03 12:40:25.25: [ 1907]: NSF remote fax equipment: unknown
lug 03 12:40:25.25: [ 1907]: NSF possible remote station ID: "                    "
lug 03 12:40:25.25: [ 1907]: <-- [9:AT+FRH=3\r]
lug 03 12:40:25.26: [ 1907]: --> [7:CONNECT]
lug 03 12:40:25.97: [ 1907]: --> [2:OK]
lug 03 12:40:25.97: [ 1907]: REMOTE CSI ""
lug 03 12:40:25.97: [ 1907]: <-- [9:AT+FRH=3\r]
lug 03 12:40:25.98: [ 1907]: --> [7:CONNECT]
lug 03 12:40:26.25: [ 1907]: --> [2:OK]
lug 03 12:40:26.25: [ 1907]: REMOTE best rate 9600 bit/s
lug 03 12:40:26.25: [ 1907]: REMOTE max page width 1728 pixels in 215 mm
lug 03 12:40:26.25: [ 1907]: REMOTE max unlimited page length
lug 03 12:40:26.25: [ 1907]: REMOTE best vres 7.7 line/mm
lug 03 12:40:26.25: [ 1907]: REMOTE best format 2-D MMR
lug 03 12:40:26.25: [ 1907]: REMOTE supports T.30 Annex A, ECM
lug 03 12:40:26.25: [ 1907]: REMOTE best 5 ms/scanline
lug 03 12:40:26.25: [ 1907]: USE 9600 bit/s
lug 03 12:40:26.25: [ 1907]: USE 5 ms/scanline
lug 03 12:40:26.25: [ 1907]: <-- [9:AT+FTH=3\r]
lug 03 12:40:26.30: [ 1907]: --> [7:CONNECT]
lug 03 12:40:26.30: [ 1907]: <-- data [3]
lug 03 12:40:26.30: [ 1907]: <-- data [2]
lug 03 12:40:27.61: [ 1907]: --> [2:OK]
lug 03 12:40:27.61: [ 1907]: <-- [5:ATH0\r]
lug 03 12:40:28.04: [ 1907]: --> [10:NO CARRIER]
lug 03 12:40:28.04: [ 1907]: MODEM No carrier
lug 03 12:40:28.04: [ 1907]: SESSION END

I can't understand where is the problem. The modem? the ps files?
tanks for helping.

Francesco


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*