|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] problems with an E-Tech external Faxmodem 56 K
Hello
I have sonce weeks aproblem with Hylafax and an E-tech external Faxmodem.
The incoming fax is not recognized
I am running Hylfax 4.1.5-104 on a SuSE 8.2 professional edition
Here is a log, and the modem conf is attached
I would really appreciate any help I could get
Jun 03 13:01:07.32: [ 3387]: SESSION BEGIN 00000033 35226876078
Jun 03 13:01:07.32: [ 3387]: HylaFAX (tm) Version 4.1.5
Jun 03 13:01:07.32: [ 3387]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Jun 03 13:01:07.32: [ 3387]: <-- [4:ATA\r]
Jun 03 13:01:10.32: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:10.32: [ 3387]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 03 13:01:10.32: [ 3387]: STATE CHANGE: ANSWERING -> RECEIVING
Jun 03 13:01:10.32: [ 3387]: MODEM input buffering enabled
Jun 03 13:01:10.32: [ 3387]: RECV FAX: begin
Jun 03 13:01:10.32: [ 3387]: RECV FAX: CDPN
Jun 03 13:01:10.32: [ 3387]: MODEM input buffering disabled
Jun 03 13:01:10.32: [ 3387]: <-- HDLC<23:FF C0 02 C6 4E 86 B2 04 16 C6 86 46
4E AE 22 04 04 04 04 04 04 04 04>
Jun 03 13:01:10.32: [ 3387]: <-- data [23]
Jun 03 13:01:10.32: [ 3387]: <-- data [2]
Jun 03 13:01:11.96: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:11.96: [ 3387]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Jun 03 13:01:11.96: [ 3387]: <-- data [10]
Jun 03 13:01:11.96: [ 3387]: <-- data [2]
Jun 03 13:01:12.37: [ 3387]: --> [2:OK]
Jun 03 13:01:12.37: [ 3387]: <-- [9:AT+FRH=3\r]
Jun 03 13:01:12.61: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:14.26: [ 3387]: --> HDLC<25:FF C0 C2 6C 6C 6C 8C 4C 2C 04 04 4C
AC CC D4 04 04 04 04 04 04 04 04 E9 66>
Jun 03 13:01:14.26: [ 3387]: --> [2:OK]
Jun 03 13:01:14.26: [ 3387]: REMOTE TSI "+352 421666"
Jun 03 13:01:14.26: [ 3387]: <-- [9:AT+FRH=3\r]
Jun 03 13:01:14.29: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:14.52: [ 3387]: --> HDLC<9:FF C8 C1 00 61 15 00 D1 06>
Jun 03 13:01:14.53: [ 3387]: --> [2:OK]
Jun 03 13:01:14.53: [ 3387]: REMOTE wants 9600 bit/s
Jun 03 13:01:14.53: [ 3387]: REMOTE wants page width 1728 pixels in 215 mm
Jun 03 13:01:14.53: [ 3387]: REMOTE wants unlimited page length
Jun 03 13:01:14.53: [ 3387]: REMOTE wants 3.85 line/mm
Jun 03 13:01:14.53: [ 3387]: REMOTE wants 2-D MR
Jun 03 13:01:14.53: [ 3387]: RECV training at v.29 9600 bit/s
Jun 03 13:01:14.53: [ 3387]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jun 03 13:01:14.53: [ 3387]: <-- [10:AT+FRM=96\r]
Jun 03 13:01:14.91: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:16.45: [ 3387]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jun 03 13:01:16.45: [ 3387]: RECV: TCF 1824 bytes, 0% non-zero, 1810 zero-run
Jun 03 13:01:16.45: [ 3387]: --> [10:NO CARRIER]
Jun 03 13:01:16.45: [ 3387]: DELAY 75 ms
Jun 03 13:01:16.53: [ 3387]: TRAINING succeeded
Jun 03 13:01:16.55: [ 3387]: <-- [9:AT+FTH=3\r]
Jun 03 13:01:16.60: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:16.60: [ 3387]: <-- HDLC<3:FF C8 21>
Jun 03 13:01:16.60: [ 3387]: <-- data [3]
Jun 03 13:01:16.60: [ 3387]: <-- data [2]
Jun 03 13:01:17.81: [ 3387]: --> [2:OK]
Jun 03 13:01:17.81: [ 3387]: MODEM input buffering enabled
Jun 03 13:01:17.81: [ 3387]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Jun 03 13:01:17.81: [ 3387]: <-- [10:AT+FRM=96\r]
Jun 03 13:01:18.40: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:18.40: [ 3387]: RECV: begin page
Jun 03 13:01:43.05: [ 3387]: RECV: 1152 total lines, 0 bad lines, 0
consecutive bad lines
Jun 03 13:01:43.05: [ 3387]: RECV: end page
Jun 03 13:01:43.05: [ 3387]: --> [10:NO CARRIER]
Jun 03 13:01:43.05: [ 3387]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jun 03 13:01:43.05: [ 3387]: MODEM input buffering disabled
Jun 03 13:01:43.05: [ 3387]: <-- [9:AT+FRH=3\r]
Jun 03 13:01:43.09: [ 3387]: --> [7:CONNECT]
Jun 03 13:01:44.12: [ 3387]: --> HDLC<5:FF C8 F4 CC 66>
Jun 03 13:01:44.13: [ 3387]: --> [2:OK]
Jun 03 13:01:44.13: [ 3387]: RECV recv EOP (no more pages or documents)
Jun 03 13:01:44.13: [ 3387]: <-- [9:AT+FRS=7\r]
Jun 03 13:02:14.13: [ 3387]: MODEM TIMEOUT: reading line from modem
Jun 03 13:02:14.22: [ 3387]: MODEM <Timeout>
Jun 03 13:02:14.22: [ 3387]: RECV FAX (00000033): recvq/fax00032.tif from
+352 421666, route to <unspecified>, 0 pages in 1:04
Jun 03 13:02:14.23: [ 3387]: RECV FAX: Failure to receive silence.
Jun 03 13:02:14.23: [ 3387]: <-- [9:AT+FTH=3\r]
Jun 03 13:02:14.25: [ 3387]: --> [2:OK]
Jun 03 13:02:14.25: [ 3387]: MODEM input buffering enabled
Jun 03 13:02:14.25: [ 3387]: RECV FAX (00000033): session with +352 421666
terminated abnormally: Failure to receive silence.
Jun 03 13:02:14.25: [ 3387]: RECV FAX: bin/faxrcvd "recvq/fax00032.tif"
"ttyS0" "00000033" "Failure to receive silence." "" "" ""
Jun 03 13:02:14.42: [ 3387]: RECV FAX: end
# $Id: class1,v 1.12 2002/08/21 16:01:07 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 352
AreaCode:
FAXNumber: "+352 26876078"
LongDistancePrefix:
InternationalPrefix: 00
DialStringRules: "etc/dialrules"
ServerTracing: 1
SessionTracing: 0xffffffff
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 3
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Durbach Marc"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "AT&K3&D0&C1" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd "<delay:7>"
#Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
