[hylafax-users] unable to receive faxes

[Eric Presley <eric@presleydesign.com>]

I have been running Hylafax on Redhat for a little while now. I 
recently went through and upgraded from redhat 7 to redhat 9 and 
installed the latest version of Hylafax. Now I can't receive faxes, 
here is a typical log

May 12 22:25:01.39: [13798]: SESSION BEGIN 00000019 19499494818958
May 12 22:25:01.40: [13798]: HylaFAX (tm) Version 4.1.5
May 12 22:25:01.40: [13798]: <-- [4:ATA\r]
May 12 22:25:13.50: [13798]: --> [5:+FCON]
May 12 22:25:13.50: [13798]: ANSWER: FAX CONNECTION  DEVICE 
'/dev/usb/ttyACM0'
May 12 22:25:13.50: [13798]: RECV FAX: begin
May 12 22:25:13.51: [13798]: --> [28:+FTSI:"            481 8958"]
May 12 22:25:13.51: [13798]: REMOTE TSI ""
May 12 22:25:13.86: [13798]: --> [21:+FDCS:1,5,0,2,1,0,0,0]
May 12 22:25:13.86: [13798]: REMOTE wants 14400 bit/s
May 12 22:25:13.86: [13798]: REMOTE wants page width 1728 pixels in 215 
mm
May 12 22:25:13.86: [13798]: REMOTE wants unlimited page length
May 12 22:25:13.86: [13798]: REMOTE wants 7.7 line/mm
May 12 22:25:13.86: [13798]: REMOTE wants 2-D MR
May 12 22:25:13.86: [13798]: --> [2:OK]
May 12 22:25:13.87: [13798]: <-- [7:AT+FDR\r]
May 12 22:25:18.13: [13798]: --> [5:+FCFR]
May 12 22:25:19.47: [13798]: --> [7:CONNECT]
May 12 22:25:19.47: [13798]: RECV: begin page
May 12 22:25:19.47: [13798]: RECV: send trigger 021
May 12 22:25:19.47: [13798]: <-- data [1]
May 12 22:25:39.97: [13798]: RECV: 967 total lines, 327 bad lines, 13 
consecutive bad lines
May 12 22:25:39.98: [13798]: --> [16:+FPTS:1,2177,0,0]
May 12 22:25:41.33: [13798]: --> [6:+FET:2]
May 12 22:25:41.33: [13798]: RECV recv EOP (no more pages or documents)
May 12 22:25:41.33: [13798]: --> [2:OK]
May 12 22:25:41.33: [13798]: RECV: REJECT page quality, 66% good lines 
(95% required)
May 12 22:25:41.33: [13798]: RECV send RTN (retrain negative)
May 12 22:25:41.33: [13798]: <-- [10:AT+FPTS=2\r]
May 12 22:25:41.43: [13798]: --> [2:OK]
May 12 22:25:41.43: [13798]: <-- [7:AT+FDR\r]
May 12 22:25:44.23: [13798]: --> [7:+FHNG:0]
May 12 22:25:44.23: [13798]: REMOTE HANGUP: Normal and proper end of 
connection (code 0)
May 12 22:25:44.24: [13798]: RECV FAX (00000019): recvq/fax00010.tif 
from 481 8958, route to <unspecified>, 0 pages in 0:31
May 12 22:25:44.24: [13798]: RECV FAX: Normal and proper end of 
connection
May 12 22:25:44.24: [13798]: RECV FAX (00000019): session with 481 8958 
terminated abnormally: Normal and proper end of connection
May 12 22:25:44.24: [13798]: RECV FAX: bin/faxrcvd "recvq/fax00010.tif" 
"usb_ttyACM0" "00000019" "Normal and proper end of connection" "" ""
May 12 22:25:45.23: [13798]: RECV FAX: end
May 12 22:25:45.23: [13798]: SESSION END

I noticed several similar posts in the list archive but most the time 
the answer was to check the cabling. In this case I don't think that 
applies since it worked fine before and I haven't changes any hardware. 
Fortunately I mostly use it for sending (which works fine by the way) 
but I would like to be able to receive faxes as well.

I sure would appreciate any ideas.

Thanks


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*