|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] HCF receive problem
I have HCF modem (conexant) and have problem with receiving faxes. I
normally starts the comunication and then die.
Is tehere somebody who has this kind of modem working ???
please i need help
thank you
Pavel Sorejs
here is my log of one of communications
May 06 18:48:47.29: [ 1507]: SESSION BEGIN 00001549 420220562023
May 06 18:48:47.29: [ 1507]: HylaFAX (tm) Version 4.1.5
May 06 18:48:47.29: [ 1507]: <-- [4:ATA\r]
May 06 18:48:54.19: [ 1507]: --> [7:CONNECT]
May 06 18:48:54.19: [ 1507]: ANSWER: FAX CONNECTION DEVICE '/dev/modem'
May 06 18:48:54.19: [ 1507]: RECV FAX: begin
May 06 18:48:54.26: [ 1507]: <-- data [23]
May 06 18:48:54.26: [ 1507]: <-- data [2]
May 06 18:48:55.77: [ 1507]: --> [7:CONNECT]
May 06 18:48:55.77: [ 1507]: <-- data [10]
May 06 18:48:55.77: [ 1507]: <-- data [2]
May 06 18:48:56.45: [ 1507]: --> [2:OK]
May 06 18:48:56.45: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:48:56.85: [ 1507]: --> [7:CONNECT]
May 06 18:48:57.91: [ 1507]: --> [2:OK]
May 06 18:48:57.91: [ 1507]: REMOTE wants 14400 bit/s
May 06 18:48:57.91: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:48:57.91: [ 1507]: REMOTE wants unlimited page length
May 06 18:48:57.91: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:48:57.91: [ 1507]: REMOTE wants 2-D MR
May 06 18:48:57.91: [ 1507]: RECV training at v.17 14400 bit/s
May 06 18:48:57.91: [ 1507]: <-- [11:AT+FRM=145\r]
May 06 18:48:59.57: [ 1507]: --> [7:CONNECT]
May 06 18:49:01.09: [ 1507]: RECV: TCF 1475 bytes, 94% non-zero, 1 zero-run
May 06 18:49:01.09: [ 1507]: RECV: reject TCF (too many non-zero, max 10%)
May 06 18:49:01.09: [ 1507]: RECV: reject TCF (zero run too short, min 1800)
May 06 18:49:01.11: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:01.11: [ 1507]: DELAY 75 ms
May 06 18:49:01.19: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:01.53: [ 1507]: --> [7:CONNECT]
May 06 18:49:01.53: [ 1507]: <-- data [3]
May 06 18:49:01.53: [ 1507]: <-- data [2]
May 06 18:49:02.93: [ 1507]: --> [2:OK]
May 06 18:49:02.93: [ 1507]: TRAINING failed
May 06 18:49:02.93: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:03.35: [ 1507]: --> [7:CONNECT]
May 06 18:49:04.43: [ 1507]: --> [2:OK]
May 06 18:49:04.43: [ 1507]: REMOTE wants 12000 bit/s
May 06 18:49:04.43: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:49:04.43: [ 1507]: REMOTE wants unlimited page length
May 06 18:49:04.43: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:49:04.43: [ 1507]: REMOTE wants 2-D MR
May 06 18:49:04.43: [ 1507]: RECV training at v.17 12000 bit/s
May 06 18:49:04.43: [ 1507]: <-- [11:AT+FRM=121\r]
May 06 18:49:06.13: [ 1507]: --> [7:CONNECT]
May 06 18:49:07.63: [ 1507]: RECV: TCF 1053 bytes, 74% non-zero, 1 zero-run
May 06 18:49:07.63: [ 1507]: RECV: reject TCF (too many non-zero, max 10%)
May 06 18:49:07.63: [ 1507]: RECV: reject TCF (zero run too short, min 1500)
May 06 18:49:07.65: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:07.65: [ 1507]: DELAY 75 ms
May 06 18:49:07.73: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:08.07: [ 1507]: --> [7:CONNECT]
May 06 18:49:08.07: [ 1507]: <-- data [3]
May 06 18:49:08.07: [ 1507]: <-- data [2]
May 06 18:49:09.47: [ 1507]: --> [2:OK]
May 06 18:49:09.47: [ 1507]: TRAINING failed
May 06 18:49:09.47: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:09.87: [ 1507]: --> [7:CONNECT]
May 06 18:49:10.95: [ 1507]: --> [2:OK]
May 06 18:49:10.95: [ 1507]: REMOTE wants 9600 bit/s
May 06 18:49:10.95: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:49:10.95: [ 1507]: REMOTE wants unlimited page length
May 06 18:49:10.95: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:49:10.95: [ 1507]: REMOTE wants 2-D MR
May 06 18:49:10.95: [ 1507]: RECV training at v.17 9600 bit/s
May 06 18:49:10.95: [ 1507]: <-- [10:AT+FRM=97\r]
May 06 18:49:12.67: [ 1507]: --> [7:CONNECT]
May 06 18:49:14.17: [ 1507]: RECV: TCF 937 bytes, 63% non-zero, 1 zero-run
May 06 18:49:14.17: [ 1507]: RECV: reject TCF (too many non-zero, max 10%)
May 06 18:49:14.17: [ 1507]: RECV: reject TCF (zero run too short, min 1200)
May 06 18:49:14.19: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:14.19: [ 1507]: DELAY 75 ms
May 06 18:49:14.27: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:14.61: [ 1507]: --> [7:CONNECT]
May 06 18:49:14.61: [ 1507]: <-- data [3]
May 06 18:49:14.61: [ 1507]: <-- data [2]
May 06 18:49:16.01: [ 1507]: --> [2:OK]
May 06 18:49:16.01: [ 1507]: TRAINING failed
May 06 18:49:16.01: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:16.41: [ 1507]: --> [7:CONNECT]
May 06 18:49:17.51: [ 1507]: --> [2:OK]
May 06 18:49:17.51: [ 1507]: REMOTE wants 2400 bit/s
May 06 18:49:17.51: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:49:17.51: [ 1507]: REMOTE wants unlimited page length
May 06 18:49:17.51: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:49:17.51: [ 1507]: REMOTE wants 2-D MR
May 06 18:49:17.51: [ 1507]: RECV training at v.17 7200 bit/s
May 06 18:49:17.51: [ 1507]: <-- [10:AT+FRM=73\r]
May 06 18:49:19.21: [ 1507]: --> [7:CONNECT]
May 06 18:49:20.71: [ 1507]: RECV: TCF 677 bytes, 99% non-zero, 1 zero-run
May 06 18:49:20.71: [ 1507]: RECV: reject TCF (too many non-zero, max 10%)
May 06 18:49:20.71: [ 1507]: RECV: reject TCF (zero run too short, min 300)
May 06 18:49:20.73: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:20.73: [ 1507]: DELAY 75 ms
May 06 18:49:20.81: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:21.15: [ 1507]: --> [7:CONNECT]
May 06 18:49:21.15: [ 1507]: <-- data [3]
May 06 18:49:21.15: [ 1507]: <-- data [2]
May 06 18:49:22.55: [ 1507]: --> [2:OK]
May 06 18:49:22.55: [ 1507]: TRAINING failed
May 06 18:49:22.55: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:22.95: [ 1507]: --> [7:CONNECT]
May 06 18:49:24.03: [ 1507]: --> [2:OK]
May 06 18:49:24.03: [ 1507]: REMOTE wants 4800 bit/s
May 06 18:49:24.03: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:49:24.03: [ 1507]: REMOTE wants unlimited page length
May 06 18:49:24.03: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:49:24.03: [ 1507]: REMOTE wants 2-D MR
May 06 18:49:24.03: [ 1507]: RECV training at v.27ter 4800 bit/s
May 06 18:49:24.03: [ 1507]: <-- [10:AT+FRM=48\r]
May 06 18:49:25.13: [ 1507]: --> [7:CONNECT]
May 06 18:49:26.55: [ 1507]: RECV: TCF 8 bytes, 0% non-zero, 0 zero-run
May 06 18:49:26.55: [ 1507]: RECV: reject TCF (zero run too short, min 600)
May 06 18:49:26.57: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:26.57: [ 1507]: DELAY 75 ms
May 06 18:49:26.65: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:26.99: [ 1507]: --> [7:CONNECT]
May 06 18:49:26.99: [ 1507]: <-- data [3]
May 06 18:49:26.99: [ 1507]: <-- data [2]
May 06 18:49:28.39: [ 1507]: --> [2:OK]
May 06 18:49:28.39: [ 1507]: TRAINING failed
May 06 18:49:28.39: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:28.81: [ 1507]: --> [7:CONNECT]
May 06 18:49:29.89: [ 1507]: --> [2:OK]
May 06 18:49:30.10: [ 1507]: REMOTE wants 2400 bit/s
May 06 18:49:30.10: [ 1507]: REMOTE wants page width 1728 pixels in 215 mm
May 06 18:49:30.10: [ 1507]: REMOTE wants unlimited page length
May 06 18:49:30.10: [ 1507]: REMOTE wants 3.85 line/mm
May 06 18:49:30.10: [ 1507]: REMOTE wants 2-D MR
May 06 18:49:30.10: [ 1507]: RECV training at v.27ter fallback mode 2400 bit/s
May 06 18:49:30.10: [ 1507]: <-- [10:AT+FRM=24\r]
May 06 18:49:31.27: [ 1507]: --> [7:CONNECT]
May 06 18:49:32.65: [ 1507]: RECV: TCF 375 bytes, 52% non-zero, 1 zero-run
May 06 18:49:32.65: [ 1507]: RECV: reject TCF (too many non-zero, max 10%)
May 06 18:49:32.65: [ 1507]: RECV: reject TCF (zero run too short, min 300)
May 06 18:49:32.67: [ 1507]: --> [10:NO CARRIER]
May 06 18:49:32.67: [ 1507]: DELAY 75 ms
May 06 18:49:32.75: [ 1507]: <-- [9:AT+FTH=3\r]
May 06 18:49:33.09: [ 1507]: --> [7:CONNECT]
May 06 18:49:33.09: [ 1507]: <-- data [3]
May 06 18:49:33.09: [ 1507]: <-- data [2]
May 06 18:49:34.49: [ 1507]: --> [2:OK]
May 06 18:49:34.49: [ 1507]: TRAINING failed
May 06 18:49:34.49: [ 1507]: <-- [9:AT+FRH=3\r]
May 06 18:49:34.87: [ 1507]: --> [7:CONNECT]
May 06 18:49:35.83: [ 1507]: --> [2:OK]
May 06 18:49:35.83: [ 1507]: RECV FAX: RSPREC error/got DCN
May 06 18:49:35.84: [ 1507]: RECV FAX: end
May 06 18:49:35.84: [ 1507]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
