|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Session *slow* to close after received fax
New user of HylaFAX. Fresh install of hylafax 4.1.5-1rh7.i386.rpm on
RedHat Linux 7.3 (fully updated), Modem in question is Aopen FM56EX
(Rockwell chipset external modem, Class 1 only).
Anyway, with relatively little effort I managed to successfully send
myself faxes from a real fax machine. Got it in only two tries. Felt
pretty good for a while. The problem is that following completion of the
transmission, the modem stays off-hook for between 6 and seven minutes
after the sending fax machine has hung up. No error messages, no other
symptoms that I can see. I've been playing with modem settings and
getting absolutely nowhere. I can't find anything in the archives or
through Google that offers any useful information.
If anyone has any suggestions, I'd really appreciate it.
I have successfully received with an old ZyXEL U1496E in Class 2 mode
without this problem. (Before you ask, the only reason I'm not using the
ZyXEL is problematic distinctive ring detection. I may be able to find
someone to burn newer firmware into the ZyXEL EPROMs, in which case
I'll use it instead of the Aopen. Meanwhile, I'm trying to deal with
this end-of-message timing situation.)
A sample log file is at the bottom of this message. Notice the gap of
6:36 near the end.
Again, thanks for any thoughts.
Bruce Halco
---
Mar 02 21:00:10.31: [10211]: SESSION BEGIN 00000013 14404404610600
Mar 02 21:00:10.31: [10211]: HylaFAX (tm) Version 4.1.5
Mar 02 21:00:10.31: [10211]: <-- [4:ATA\r]
Mar 02 21:00:16.41: [10211]: --> [7:CONNECT]
Mar 02 21:00:16.41: [10211]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1'
Mar 02 21:00:16.41: [10211]: RECV FAX: begin
Mar 02 21:00:16.41: [10211]: <-- data [23]
Mar 02 21:00:16.41: [10211]: <-- data [2]
Mar 02 21:00:18.10: [10211]: --> [7:CONNECT]
Mar 02 21:00:18.10: [10211]: <-- data [10]
Mar 02 21:00:18.10: [10211]: <-- data [2]
Mar 02 21:00:18.64: [10211]: --> [2:OK]
Mar 02 21:00:18.64: [10211]: <-- [9:AT+FRH=3\r]
Mar 02 21:00:19.17: [10211]: --> [7:CONNECT]
Mar 02 21:00:20.22: [10211]: --> [2:OK]
Mar 02 21:00:20.22: [10211]: REMOTE wants 9600 bit/s
Mar 02 21:00:20.22: [10211]: REMOTE wants page width 1728 pixels in 215 mm
Mar 02 21:00:20.22: [10211]: REMOTE wants unlimited page length
Mar 02 21:00:20.22: [10211]: REMOTE wants 3.85 line/mm
Mar 02 21:00:20.22: [10211]: REMOTE wants 1-D MR
Mar 02 21:00:20.22: [10211]: RECV training at v.29 9600 bit/s
Mar 02 21:00:20.22: [10211]: <-- [10:AT+FRM=96\r]
Mar 02 21:00:20.56: [10211]: --> [7:CONNECT]
Mar 02 21:00:22.13: [10211]: RECV: TCF 1855 bytes, 2% non-zero, 1810
zero-run
Mar 02 21:00:22.13: [10211]: --> [10:NO CARRIER]
Mar 02 21:00:22.13: [10211]: DELAY 75 ms
Mar 02 21:00:22.21: [10211]: TRAINING succeeded
Mar 02 21:00:22.21: [10211]: <-- [9:AT+FTH=3\r]
Mar 02 21:00:22.26: [10211]: --> [7:CONNECT]
Mar 02 21:00:22.26: [10211]: <-- data [3]
Mar 02 21:00:22.26: [10211]: <-- data [2]
Mar 02 21:00:23.57: [10211]: --> [2:OK]
Mar 02 21:00:23.57: [10211]: <-- [10:AT+FRM=96\r]
Mar 02 21:00:24.16: [10211]: --> [7:CONNECT]
Mar 02 21:00:24.16: [10211]: RECV: begin page
Mar 02 21:00:42.09: [10211]: RECV: 1060 total lines, 0 bad lines, 0
consecutive bad lines
Mar 02 21:00:42.09: [10211]: RECV: end page
Mar 02 21:00:42.09: [10211]: --> [10:NO CARRIER]
Mar 02 21:00:42.09: [10211]: <-- [9:AT+FRH=3\r]
Mar 02 21:00:42.45: [10211]: --> [7:CONNECT]
Mar 02 21:00:43.21: [10211]: --> [2:OK]
Mar 02 21:00:43.21: [10211]: RECV recv EOP (no more pages or documents)
Mar 02 21:00:43.21: [10211]: <-- [9:AT+FRS=7\r]
Mar 02 21:00:43.33: [10211]: --> [2:OK]
Mar 02 21:00:43.33: [10211]: <-- [9:AT+FTH=3\r]
Mar 02 21:00:43.38: [10211]: --> [7:CONNECT]
Mar 02 21:00:43.38: [10211]: <-- data [3]
Mar 02 21:00:43.38: [10211]: <-- data [2]
Mar 02 21:00:44.69: [10211]: --> [2:OK]
Mar 02 21:00:44.69: [10211]: RECV send MCF (message confirmation)
Mar 02 21:00:44.69: [10211]: RECV FAX (00000013): from <UNSPECIFIED>,
page 1 in 0:22, INF, 3.85 line/mm, 1-D MR, 9600 bit/s
Mar 02 21:00:44.69: [10211]: RECV FAX (00000013): recvq/fax00013.tif
from <UNSPECIFIED>, route to <unspecified>, 1 pages in 0:28
Mar 02 21:00:44.69: [10211]: <-- [9:AT+FRH=3\r]
Mar 02 21:00:45.11: [10211]: --> [7:CONNECT]
Mar 02 21:00:46.01: [10211]: --> [2:OK]
Mar 02 21:00:46.01: [10211]: RECV FAX: bin/faxrcvd "recvq/fax00013.tif"
"ttyS1" "00000013" "" "" ""
Mar 02 21:07:22.23: [10211]: RECV FAX: end
Mar 02 21:07:22.23: [10211]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
