[hylafax-users] using hylafax with nokia 6210

[Kurt Weiss <info@kwnet.at>]

hello all

i've problems using hylafax width nokia 6210 mobile phone.
does somebody work successfully width it?

the problem:
after a half page, the fax sends garbage, then the transmittion stops,
the log message is:
no response to MPS or EOP repeated 3 times

i had the same problem with an US-Robotics Sportster, but there i 
changed successfully to class 1...

i've tested class 1, class 2 class 2.0
additionally i've tested modem rate from 38400 - 9600
this only changes the position where hylafax terminates (between nothing 
and a half page)

here's my (last) config.ttyS0: - sending a half page - then garbage...

CountryCode:		43
AreaCode:		699
FAXNumber:		+43.699.4272.9926
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		low
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	www.kwnet.at
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25

ModemType:		Class1		# use this to supply a hint
ModemRate:		14400		# rate for DCE-DTE communication

################i've testet this / without success
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
#GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data

#ModemDialCmd:		ATDT%s		# T for tone dialing

################i've testet this / without success
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd

#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait 
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait 
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait 
Class1MsgRecvHackCmd:	""	# command to avoid +FCERROR before image
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & 
Class1SendMsgDelay:	75		# 75ms delay after training
Class1SwitchingCmd:	AT+FRS=7	# silence between HDLC recv and 
Class1TrainingRecovery:	1500		# 1.5sec delay after training 
Class1RecvAbortOK:	200
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC 
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident 
Class1TCFMaxNonZero:	10		# max 10% of data may be Class1TCFMinRun: 
1000		# min run is 2/3rds of TCF

thx in adv
kurt


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*