[hylafax-users] using hylafax with nokia 6210

[Kurt Weiss <input.maillists@kwnet.at>]

hello all

i've problems using hylafax width nokia 6210 mobile phone.
does somebody work successfully width it?

the problem:
after a half page, the fax sends garbage, then the transmittion stops,
the log message is:
no response to MPS or EOP repeated 3 times

i had the same problem with an US-Robotics Sportster, but there i
changed successfully to class 1...

i've tested class 1, class 2 class 2.0
additionally i've tested modem rate from 38400 - 9600
this only changes the position where hylafax terminates (between nothing
and a half page)

here's my (last) config.ttyS0: - sending a half page - then garbage...

> CountryCode:        43
> AreaCode:        699
> FAXNumber:        +43.699.4272.9926
> LongDistancePrefix:    0
> InternationalPrefix:    00
> DialStringRules:    etc/dialrules
> ServerTracing:        1
> SessionTracing:        11
> RecvFileMode:        0600
> LogFileMode:        0600
> DeviceMode:        0600
> RingsBeforeAnswer:    1
> SpeakerVolume:        low
> GettyArgs:        "-h %l dx_%s"
> LocalIdentifier:    www.kwnet.at
> TagLineFont:        etc/lutRS18.pcf
> TagLineFormat:        "From %%l|%c|Page %%P of %%T"
> MaxRecvPages:        25
> 
> ModemType:        Class1        # use this to supply a hint
> ModemRate:        14400        # rate for DCE-DTE communication
> 
> ################i've testet this / without success
> #ModemFlowControl:    xonxoff        # XON/XOFF flow control assumed
> #
> ModemSetupDTRCmd:    AT&D2        # setup so DTR drop resets modem
> ModemSetupDCDCmd:    AT&C1        # setup so DCD follows carrier
> #GettyArgs:        "-h %l dx_%s"    # modem must auto-detect fax/data
> 
> #ModemDialCmd:        ATDT%s        # T for tone dialing
> 
> ################i've testet this / without success
> #ModemHardFlowCmd:    AT&K3        # hardware flow control cmd
> 
> #
> Class1Cmd:        AT+FCLASS=1    # command to enter class 1
> Class1PPMWaitCmd:    AT+FTS=7    # command to stop and wait 
> Class1TCFWaitCmd:    AT+FTS=7    # command to stop and wait 
> Class1EOPWaitCmd:    AT+FTS=9    # command to stop and wait 
> Class1MsgRecvHackCmd:    ""    # command to avoid +FCERROR before image
> Class1TCFResponseDelay:    75        # 75ms delay between recv TCF & 
> Class1SendMsgDelay:    75        # 75ms delay after training
> Class1SwitchingCmd:    AT+FRS=7    # silence between HDLC recv and 
> Class1TrainingRecovery:    1500        # 1.5sec delay after training 
> Class1RecvAbortOK:    200
> Class1FrameOverhead:    4        # 4 byte overhead in recvd HDLC 
> Class1RecvIdentTimer:    40000        # 35+5secs waiting for ident 
> Class1TCFMaxNonZero:    10        # max 10% of data may be 
> Class1TCFMinRun: 1000        # min run is 2/3rds of TCF

thx in adv
kurt




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*