[hylafax-users] Answering always in fax mode

["Cassiano Surek" <cassiano@loducca.com.br>]

Hello you all,

Is there a way to set the config files to always answer the phone in fax
mode?

The situation is that from one machine everything works fine (this one
is a Canon Copier with Fax facilities) while on another fax machine (a
simpler one) it does not receive.

Below, my config files and a log file of what goes on. Looks like the
getty is answering in data mode...


****************** config **********************
LogFacility:		daemon
CountryCode:		55
AreaCode:		41
LongDistancePrefix:	021
InternationalPrefix:	0210
DialStringRules:	etc/dialrules
ServerTracing:		1




****************** config.ttyS4 **********************

# $Id: usr-xon,v 1.6 2002/04/07 20:29:27 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software
and 
# its documentation for any purpose is hereby granted without fee,
provided
# that (i) the above copyright notices and this permission notice appear
in
# all copies of the software and related documentation, and (ii) the
names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY
KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY
OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE

# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control. 
#
#
CountryCode:		55
AreaCode:		41
FAXNumber:		+55.41.3027.3517
LongDistancePrefix:	021
InternationalPrefix:	0210
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	2
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Loducca Sul"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# hardware flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier
(or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow
control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow
control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow
control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX returns a multi-line
result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow
control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow
control
Class1SFLOCmd:		""		# modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FCLASS=0	# leave modem idling in class 0
ModemAnswerCmd:		AT+FCLASS=1A	# answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0






**************** Log ************************

Dec 19 15:05:36.89: [15996]: SESSION BEGIN 00000014 554130273517
Dec 19 15:05:36.89: [15996]: HylaFAX (tm) Version 4.1.3
Dec 19 15:05:36.89: [15996]: <-- [4:ATA\r]
Dec 19 15:05:55.55: [15996]: --> [4:+FDM]
Dec 19 15:05:55.55: [15996]: ANSWER: DATA CONNECTION
Dec 19 15:05:55.55: [15996]: GETTY: START "/sbin/mgetty -h ttyS4
dx_19200", pid 16346
Dec 19 15:05:55.71: [15996]: GETTY: exit status 01000
Dec 19 15:05:55.71: [15996]: SESSION END

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*