|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Appendix to my earlier mail...
Hello, Giulio,
and THANKS for answering my emergency cry...
On Mon, 18 Nov 2002, Giulio Orsero wrote:
| On Mon, 18 Nov 2002 18:53:56 +0100 (CET), Rainer Hantsch
| <rainer@hantsch.co.at> wrote:
|
| >o I can receive FAXes without any problem.
|
| >o When I try to send a FAX to one of my old HylaFAX servers (Hylafax which
| > came with SuSE 5.2, running on SuSE 5.2), I loose roughly 2cm of the page
| > in small stripes, the rest if clearely visible.
| >o When I try the same with my CANON FAX machine as target, I loose nearely
| > 50% of the page. The remaining image stripes have a height of roughly 1cm
| > and are clearely visible.
| Do you use the same config files or new ones?
I inserted below my configuration files for your reference. The file named
'config.ttyQ1a1' is my old server's config file. The server has an intelligent
Equinox 4xSerial-Port card inside, therefore this unusual device name. But
this config file also works smoothly with other servers on ttyS1 after
renaming.
First, I did a default 'faxaddmodem' and entered the parameters as described
in the SuSE 7.0 handbook. With this settings, I had the above problems. You
can see the configuration below in file config.ttyS1.
Then I copied without any change the .../etc/config.ttyQ1a1 file from my
working HylaFax server and named it config.ttyS1. -> Again same problem.
You see the configuration file below.
---<.../etc/config>-----------------
LogFacility: daemon
CountryCode: 43
AreaCode: 1
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 527
ContCoverPage: etc/cover.templ
MaxSendPages: 30
ModemGroup: "any:.*"
PostScriptTimeout: 3600
SessionTracing: 527
--<eof>------------------------------------
--<.../etc/config.ttyS1 -- generated by faxaddmodem>-------------------
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 43
AreaCode: 1
FAXNumber: +43.1.798853818
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0666
RingsBeforeAnswer: 4
SpeakerVolume: low
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Ing. Rainer Hantsch"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 90
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendPPMDelay: 75 # 75ms delay before sending PPM
Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF
Class1SwitchingDelay: 150 # 150ms delay in switching transmission direction
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
--<eof>---------------------------------
--<.../etc/config.ttyQ1a1 -- config of my working server>------------------
--< This configuration file works perfectly on my server since 2 years!>---
CountryCode: 43
AreaCode: 1
FAXNumber: +43.1.798853818
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: "etc/dialrules.europe"
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
#GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "Ing. Rainer HANTSCH (+43-1-7988538-18)"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "··· From %%l|%c|Page %%p of %%t"
MaxRecvPages: 99
PercentGoodLines: 75
MaxBadCalls: 10
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # hint to override class 2
ModemRate: 19200 # locked for fax sending
ModemFlowControl: xonxoff # default
#
ModemSetupDTRCmd: AT&D2 # DTR off causes modem to hangup
ModemSetupDCDCmd: AT&C0 # DCD always on
#
ModemMfrQueryCmd: !Nuvo
ModemModelQueryCmd: !9624PFX
ModemRevQueryCmd: ATI3
#
ModemDialCmd: ATX1M1+FCLASS=1DT0,%s
ModemAnswerCmd: ATM0A
#
# Habe ich am 11.9.2001 angehängt, weil sich Modem aufgehängt hat...
ModemSoftResetCmd: AT&F
ModemResetCmds: AT&F
--<eof>------------------------------------------------------
| Have you checked flow control settings?
This was the first I thought, too, so i played with the settings here.
The original config file (which I tried first) was configured using 'default'
flow control. But the config file from my working server uses explicitly
'xonxoff'. - Both configurations do not work and cause identical errors.
mfg
Ing. Rainer Hantsch
--
\\|// Ing. Rainer HANTSCH - Hardware + Software
(o o) Forget Windoze! -- We focus on L-I-N-U-X...
--oOOo-(_)-oOOo--------------------------------------------------
Ing. Rainer HANTSCH | e-Mail: office@hantsch.co.at
Khunngasse 21/20 | www : http://www.hantsch.co.at
A-1030 Vienna | Tel. : ++43 - 1 - 7988538 0
---------------------| Fax : ++43 - 1 - 7988538 18
** AUSTRIA ** | Mobile: ++43 - 664 - 9194382
-----------------------------------------------------------------
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
