|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] no local dialtone, queue not sent
Hi all
i have two problems with my new installed fax-server:
1) queued faxes are not sent
2) one send-try after hours: errormessage: no local dialton
this is the running system:
>211-schlagzeug.intern.ebewe.at HylaFAX server status:
> HylaFAX (tm) Version 4.1beta2
> Connected to localhost (127.0.0.1)
> Waiting for user name
> Time values are handled in GMT
> Idle timeout set to 900 seconds
> Using long replies
> No server down time currently scheduled
> HylaFAX scheduler reached at /FIFO (not connected)
> Server FIFO is /client/2071 (open)
> File cache: 0 lookups, 0 hits (0.0%), 0.0 avg probes
> 0 entries (0.0 KB), 0 entries displaced, 0 entries flushed
> TYPE: ASCII; STRU: File; MODE: Stream; FORM: PS
> No client data connection
two faxes waiting in the queue:
>HylaFAX scheduler on schlagzeug.intern.ebewe.at: Running
>Modem ttyS0 (+43.7665.8123.1480): Running and idle
>
>JID Pri S Owner Number Pages Dials TTS Status
>5 125 S root 11 0:75 2:12 17:37 No local dialtone
>6 124 S root 0812311 0:1 3:12 17:45 No local dialtone
a communication log:
>Okt 29 17:38:00.78: [ 2075]: SESSION BEGIN 00000014 11
>Okt 29 17:38:00.78: [ 2075]: SEND FAX: JOB 5 DEST 11 COMMID 00000014
>Okt 29 17:38:15.54: [ 2075]: SEND FAILED: No local dialtone
>Okt 29 17:38:15.67: [ 2075]: SESSION END
Modem: ELSA Microlink 56k pro
MODEM +FMI: "ELSA AG, AACHEN (GERMANY)" +FMM: "MicroLink 56k pro"/+FMR:
"Version 1.59 / 23.02.1999"
config-file:
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 0043
AreaCode: 7665
FAXNumber: +43.7665.8123.1480
LongDistancePrefix: 0
InternationalPrefix: 0
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 111
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "EBEWE Pharma Unterach Austria"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Von %%l|%c|Seite %%p von %%t"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
ModemRate: 38400 # max rate for DCE-DTE
communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDT,%s # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: ATX3 # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT\Q0 # disable flow control cmd
ModemHardFlowCmd: AT\Q3 # hardware flow control cmd
ModemSoftFlowCmd: AT\Q1 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
(direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality
proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command
----------------------------------------------------------------------
Wolfgang Fuertbauer (E-Mail: Wolfgang.Fuertbauer@ebewe.com)
EBEWE Pharma Tel: ++43 7665 8123 315
Mondseestrasse 11 Fax: ++43 7665 8123 11
4866 Unterach, Austria
http://www.ebewe.com
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
