|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] MPS Response problems for remote transmission
Hi.
I have been trying to send a fax to a location in Germany, and although I
handshake with the remote modem, and transmission begins, I end because of
no response to MPS's.
This is awful strange as this is a commercial fax. Is there something I
need to fix in my setup in order to deal with this?
Thanks in advance.
Sunil
p.s. The information is given below for the call.
Sep 06 14:47:26.79: [ 1601]: SESSION BEGIN 00000083 49361xxxxxxx
Sep 06 14:47:26.79: [ 1601]: HylaFAX (tm) Version 4.1.3
Sep 06 14:47:26.79: [ 1601]: SEND FAX: JOB 35 DEST 01149361xxxxxxx COMMID
00000083
DEVICE '/dev/ttyS0'
Sep 06 14:47:26.79: [ 1601]: DELAY 75 ms
Sep 06 14:47:26.87: [ 1601]: DELAY 2600 ms
Sep 06 14:47:29.47: [ 1601]: <-- [4:ATZ\r]
Sep 06 14:47:29.61: [ 1601]: --> [3:ATZ]
Sep 06 14:47:29.61: [ 1601]: --> [2:OK]
Sep 06 14:47:29.61: [ 1601]: DELAY 3000 ms
Sep 06 14:47:32.61: [ 1601]: <-- [9:AT#CID=1\r]
Sep 06 14:47:32.75: [ 1601]: --> [8:AT#CID=1]
Sep 06 14:47:32.75: [ 1601]: --> [2:OK]
Sep 06 14:47:32.75: [ 1601]: <-- [5:ATE0\r]
Sep 06 14:47:32.89: [ 1601]: --> [4:ATE0]
Sep 06 14:47:32.89: [ 1601]: --> [2:OK]
Sep 06 14:47:32.89: [ 1601]: <-- [5:ATV1\r]
Sep 06 14:47:33.03: [ 1601]: --> [2:OK]
Sep 06 14:47:33.03: [ 1601]: <-- [7:ATQ0X4\r]
Sep 06 14:47:33.17: [ 1601]: --> [2:OK]
Sep 06 14:47:33.17: [ 1601]: <-- [7:ATS0=0\r]
Sep 06 14:47:33.31: [ 1601]: --> [2:OK]
Sep 06 14:47:33.31: [ 1601]: <-- [7:ATS8=2\r]
Sep 06 14:47:33.45: [ 1601]: --> [2:OK]
Sep 06 14:47:33.45: [ 1601]: <-- [8:ATS7=60\r]
Sep 06 14:47:33.59: [ 1601]: --> [2:OK]
Sep 06 14:47:33.59: [ 1601]: <-- [12:AT&H1&I0&R2\r]
Sep 06 14:47:33.73: [ 1601]: --> [2:OK]
Sep 06 14:47:33.73: [ 1601]: <-- [11:ATS13=1&D2\r]
Sep 06 14:47:33.87: [ 1601]: --> [2:OK]
Sep 06 14:47:33.87: [ 1601]: <-- [6:AT&C1\r]
Sep 06 14:47:34.01: [ 1601]: --> [2:OK]
Sep 06 14:47:34.01: [ 1601]: <-- [14:AT+FCLASS=2.0\r]
Sep 06 14:47:34.15: [ 1601]: --> [2:OK]
Sep 06 14:47:34.15: [ 1601]: <-- [9:AT+FLO=2\r]
Sep 06 14:47:34.29: [ 1601]: --> [2:OK]
Sep 06 14:47:34.29: [ 1601]: <-- [9:AT+FPP=0\r]
Sep 06 14:47:34.43: [ 1601]: --> [2:OK]
Sep 06 14:47:34.43: [ 1601]: <-- [9:AT+FBO=0\r]
Sep 06 14:47:34.57: [ 1601]: --> [2:OK]
Sep 06 14:47:34.57: [ 1601]: <-- [10:AT+FCT=30\r]
Sep 06 14:47:34.71: [ 1601]: --> [2:OK]
Sep 06 14:47:34.71: [ 1601]: <-- [15:AT+FNR=1,1,1,0\r]
Sep 06 14:47:34.86: [ 1601]: --> [2:OK]
Sep 06 14:47:34.86: [ 1601]: <-- [9:AT+FIE=0\r]
Sep 06 14:47:35.00: [ 1601]: --> [2:OK]
Sep 06 14:47:35.00: [ 1601]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 06 14:47:35.15: [ 1601]: --> [2:OK]
Sep 06 14:47:35.15: [ 1601]: <-- [5:ATM1\r]
Sep 06 14:47:35.29: [ 1601]: --> [2:OK]
Sep 06 14:47:35.29: [ 1601]: <-- [14:AT+FCLASS=2.0\r]
Sep 06 14:47:35.53: [ 1601]: --> [2:OK]
Sep 06 14:47:35.53: [ 1601]: <-- [9:AT+FLO=2\r]
Sep 06 14:47:35.77: [ 1601]: --> [2:OK]
Sep 06 14:47:35.77: [ 1601]: <-- [9:AT+FPP=0\r]
Sep 06 14:47:36.01: [ 1601]: --> [2:OK]
Sep 06 14:47:36.01: [ 1601]: <-- [9:AT+FBO=0\r]
Sep 06 14:47:36.25: [ 1601]: --> [2:OK]
Sep 06 14:47:36.25: [ 1601]: <-- [10:AT+FCT=30\r]
Sep 06 14:47:36.49: [ 1601]: --> [2:OK]
Sep 06 14:47:36.49: [ 1601]: <-- [15:AT+FNR=1,1,1,0\r]
Sep 06 14:47:36.74: [ 1601]: --> [2:OK]
Sep 06 14:47:36.74: [ 1601]: <-- [9:AT+FIE=0\r]
Sep 06 14:47:36.98: [ 1601]: --> [2:OK]
Sep 06 14:47:36.98: [ 1601]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 06 14:47:37.23: [ 1601]: --> [2:OK]
Sep 06 14:47:37.23: [ 1601]: <-- [25:AT+FLI="+1.718.xxx.xxxx"\r]
Sep 06 14:47:37.48: [ 1601]: --> [2:OK]
Sep 06 14:47:37.48: [ 1601]: DIAL 011493616571141
Sep 06 14:47:37.48: [ 1601]: <-- [24:ATDT*70,01149361xxxxxxx\r]
Sep 06 14:48:03.69: [ 1601]: --> [4:+FCO]
Sep 06 14:48:06.90: [ 1601]: --> [27:+FCI:" +49 361 xxxxxxx"]
Sep 06 14:48:06.90: [ 1601]: REMOTE CSI "+49 361 6571141"
Sep 06 14:48:06.90: [ 1601]: --> [20:+FIS:1,5,0,2,1,0,1,1]
Sep 06 14:48:06.90: [ 1601]: --> [2:OK]
Sep 06 14:48:06.90: [ 1601]: REMOTE best rate 14400 bit/s
Sep 06 14:48:06.90: [ 1601]: REMOTE max page width 1728 pixels in 215 mm
Sep 06 14:48:06.90: [ 1601]: REMOTE max unlimited page length
Sep 06 14:48:06.90: [ 1601]: REMOTE best vres 7.7 line/mm
Sep 06 14:48:06.90: [ 1601]: REMOTE best format 2-D MR
Sep 06 14:48:06.90: [ 1601]: REMOTE best 5 ms/scanline
Sep 06 14:48:06.90: [ 1601]: USE 14400 bit/s
Sep 06 14:48:06.90: [ 1601]: USE 5 ms/scanline
Sep 06 14:48:06.90: [ 1601]: SEND file "docq/doc35.cover;01"
Sep 06 14:48:06.90: [ 1601]: USE page width 1728 pixels in 215 mm
Sep 06 14:48:06.90: [ 1601]: USE unlimited page length
Sep 06 14:48:06.90: [ 1601]: USE 7.7 line/mm
Sep 06 14:48:06.90: [ 1601]: USE 1-D MR
Sep 06 14:48:06.90: [ 1601]: <-- [23:AT+FIS=1,5,0,2,0,0,0,1\r]
Sep 06 14:48:07.15: [ 1601]: --> [2:OK]
Sep 06 14:48:07.15: [ 1601]: <-- [7:AT+FDT\r]
Sep 06 14:48:07.43: [ 1601]: --> [20:+FCS:1,5,0,2,0,0,0,1]
Sep 06 14:48:14.51: [ 1601]: --> [7:CONNECT]
Sep 06 14:48:14.51: [ 1601]: SEND begin page
Sep 06 14:48:30.55: [ 1601]: SENT 30208 bytes of data
Sep 06 14:48:30.55: [ 1601]: SEND 1D RTC
Sep 06 14:48:30.55: [ 1601]: SEND end page
Sep 06 14:48:30.55: [ 1601]: SEND send MPS (more pages, same document)
Sep 06 14:48:49.49: [ 1601]: --> [7:+FHS:52]
Sep 06 14:48:49.49: [ 1601]: REMOTE HANGUP: No response to MPS repeated 3
times
(code 52)
Sep 06 14:48:49.49: [ 1601]: SEND: No response to MPS repeated 3 times;
Giving up
after 3 attempts to send same page "docq/doc35.cover;01", dirnum 0
Sep 06 14:48:49.49: [ 1601]: <-- [5:ATH0\r]
Sep 06 14:48:49.61: [ 1601]: --> [2:OK]
Sep 06 14:48:49.61: [ 1601]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
