Re: [hylafax-users] Distinctive Ring and Answering Fax ONLY

["Sunil William Savkar" <savkar@inthespace.com>]

First here is a log file which shows my calling twice, once on the voice
line, and then once on the fax line (I guess both the same line, different
rings):

Sep  3 14:26:22 sunserver FaxGetty[28039]: MODEM U.S. ROBOTICS 56K FAX /
Sep  3 14:26:43 sunserver FaxGetty[28039]: ANSWER: CID NUMBER "RING A"
NAME "RIN
G A"
Sep  3 14:28:31 sunserver FaxGetty[28039]: ANSWER: Ring detected without
success
ful handshake
Sep  3 14:28:44 sunserver FaxGetty[28039]: MODEM U.S. ROBOTICS 56K FAX /
Sep  3 14:30:00 sunserver FaxGetty[28039]: ANSWER: Ring detected without
success
ful handshake

Here is my config file for my config.*

#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:            1
AreaCode:               718
FAXNumber:              +1.718.852.6889
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
SpeakerVolume:          medium
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Birkmann/Savkar"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           100
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              19200           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC:  yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd:       none
ModemDialCmd:           ATDT*70,%s
RecvDataFormat:         "1-D MR"
MaxConsecutiveBadLines: 10
PercentGoodLines:       50
RingFax:                "RING B"

Any help greatly greatly appreciated.  This is a bit frustrating and very
strange to say the least.

Sunil




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*