|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] 4.1.3 login question
Is this normal?
# telnet localhost 4559
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
220 emc server (HylaFAX (tm) Version 4.1.3) ready.
user test
230 User test logged in.
user foobar
230 User foobar logged in.
user dingus
230 User dingus logged in.
user hello
230 User hello logged in.
None of these users have been defined anywhere.
-Patrick Price
Keith Waters wrote:
>Hi - I am getting the following error (see full error below) on SOME
>incoming faxes on my Eicon Diva 2fx. I added the modems using the configs
>Eicon sent me
>
>I got the following info off the Internet:
>
>" RECV: Missing EOL after 5 seconds. The server timed out
> while receiving page data. This typically is caused by a
> flow control configuration problem that causes data from the
> modem to the host to be stopped." - man page
>
>" The modem failed to receive any fax image data after being sent control-Q.
>" - from hylafax message archive
>
>This seems to always happen when receiving faxes from the program
>'Rightfax' - could be something, or could be a coincidence.
>
>Have you any ideas how I would solve this one, please?
>
>Thanks
>regards,
>Keith
>
>Subject: facsimile not received
>Date: Wed, 31 Jul 2002 10:57:36 +0200
>From: The Intercape Fax Receiver <fax@fax.intercape.co.za>
>To: FaxMaster@fax.intercape.co.za
>
>
>
>An attempt to receive facsimile on ttyds01 failed because:
>
> Missing EOL after 5 seconds (section 3.2/T.4)
>
> ---- Transcript of session follows ----
>
>Jul 31 10:54:51.03: [ 252]: SESSION BEGIN 00000984 27213802088
>Jul 31 10:54:51.03: [ 252]: HylaFAX (tm) Version 4.1.1
>Jul 31 10:54:51.03: [ 252]: <-- [4:ATA\r]
>Jul 31 10:55:05.77: [ 252]: --> [5:+FCON]
>Jul 31 10:55:05.77: [ 252]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyds01'
>Jul 31 10:55:05.77: [ 252]: MODEM input buffering enabled
>Jul 31 10:55:05.77: [ 252]: RECV FAX: begin
>Jul 31 10:55:05.77: [ 252]: --> [26:+FTSI: STANDARD BANK]
>Jul 31 10:55:05.77: [ 252]: REMOTE TSI "STANDARD BANK"
>Jul 31 10:55:05.77: [ 252]: --> [22:+FDCS: 1,5,0,2,0,2,0,0]
>Jul 31 10:55:05.77: [ 252]: REMOTE wants 14400 bit/s
>Jul 31 10:55:05.77: [ 252]: REMOTE wants page width 1728 pixels in 215 mm
>Jul 31 10:55:05.77: [ 252]: REMOTE wants unlimited page length
>Jul 31 10:55:05.77: [ 252]: REMOTE wants 7.7 line/mm
>Jul 31 10:55:05.77: [ 252]: REMOTE wants 1-D MR
>Jul 31 10:55:05.77: [ 252]: REMOTE wants T.30 Annex C, half duplex ECM
>Jul 31 10:55:05.77: [ 252]: --> [2:OK]
>Jul 31 10:55:05.77: [ 252]: <-- [7:AT+FDR\r]
>Jul 31 10:55:05.87: [ 252]: --> [5:+FCFR]
>Jul 31 10:55:05.87: [ 252]: --> [22:+FDCS: 1,5,0,2,0,2,0,0]
>Jul 31 10:55:05.87: [ 252]: REMOTE wants 14400 bit/s
>Jul 31 10:55:05.87: [ 252]: REMOTE wants page width 1728 pixels in 215 mm
>Jul 31 10:55:05.87: [ 252]: REMOTE wants unlimited page length
>Jul 31 10:55:05.87: [ 252]: REMOTE wants 7.7 line/mm
>Jul 31 10:55:05.87: [ 252]: REMOTE wants 1-D MR
>Jul 31 10:55:05.87: [ 252]: REMOTE wants T.30 Annex C, half duplex ECM
>Jul 31 10:55:05.87: [ 252]: --> [7:CONNECT]
>Jul 31 10:55:05.87: [ 252]: RECV: begin page
>Jul 31 10:55:05.87: [ 252]: RECV: send trigger 021
>Jul 31 10:55:16.64: [ 252]: RECV: 2199 total lines, 0 bad lines, 0
>consecutive bad lines
>Jul 31 10:55:16.64: [ 252]: --> [13:+FPTS: 1,2200]
>Jul 31 10:55:16.64: [ 252]: --> [7:+FET: 1]
>Jul 31 10:55:16.64: [ 252]: RECV recv EOM (more documents)
>Jul 31 10:55:16.64: [ 252]: --> [2:OK]
>Jul 31 10:55:16.64: [ 252]: RECV send MCF (message confirmation)
>Jul 31 10:55:16.64: [ 252]: RECV FAX (00000984): from STANDARD BANK, page 1
>in 0:11, INF, 7.7 line/mm, 1-D MR, 14400 bit/s
>Jul 31 10:55:16.64: [ 252]: RECV FAX (00000984): recvq/fax00215.tif from
>STANDARD BANK, route to <unspecified>, 1 pages in 0:11
>Jul 31 10:55:16.64: [ 252]: <-- [7:AT+FDR\r]
>Jul 31 10:55:32.53: [ 252]: --> [22:+FDCS: 0,5,0,2,0,2,0,0]
>Jul 31 10:55:32.53: [ 252]: REMOTE wants 14400 bit/s
>Jul 31 10:55:32.53: [ 252]: REMOTE wants page width 1728 pixels in 215 mm
>Jul 31 10:55:32.53: [ 252]: REMOTE wants unlimited page length
>Jul 31 10:55:32.53: [ 252]: REMOTE wants 3.85 line/mm
>Jul 31 10:55:32.53: [ 252]: REMOTE wants 1-D MR
>Jul 31 10:55:32.53: [ 252]: REMOTE wants T.30 Annex C, half duplex ECM
>Jul 31 10:55:32.53: [ 252]: --> [2:OK]
>Jul 31 10:55:32.53: [ 252]: RECV: begin page
>Jul 31 10:55:32.53: [ 252]: RECV: send trigger 021
>Jul 31 10:57:35.57: [ 252]: MODEM TIMEOUT: reading from modem
>Jul 31 10:57:35.57: [ 252]: RECV: Missing EOL after 5 seconds
>Jul 31 10:57:35.57: [ 252]: REMOTE HANGUP: Missing EOL after 5 seconds
>(section 3.2/T.4) (code 91)
>Jul 31 10:57:35.57: [ 252]: RECV FAX (00000984): recvq/fax00216.tif from
>STANDARD BANK, route to <unspecified>, 0 pages in 2:19
>Jul 31 10:57:35.57: [ 252]: RECV FAX: Missing EOL after 5 seconds (section
>3.2/T.4)
>Jul 31 10:57:35.57: [ 252]: <-- [6:AT+FK\r]
>Jul 31 10:57:35.67: [ 252]: --> [5:ERROR]
>Jul 31 10:57:35.67: [ 252]: MODEM Command error
>Jul 31 10:57:35.67: [ 252]: RECV FAX: bin/faxrcvd "recvq/fax00215.tif"
>"ttyds01" "00000984" "" "" "RING CID: DAD: 2080"
>Jul 31 10:57:35.90: [ 252]: RECV FAX (00000984): session with STANDARD BANK
>terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
>Jul 31 10:57:35.90: [ 252]: RECV FAX: bin/faxrcvd "recvq/fax00216.tif"
>"ttyds01" "00000984" "Missing EOL after 5 seconds (section 3.2/T.4)" ""
>"RING CID: DAD: 2080"
>
>
>
>
>
>____________________ HylaFAX(tm) Users Mailing List _______________________
> To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
