[hylafax-users] Unspecified Phase C error

[Mike Liguit <mikel@asti.dost.gov.ph>]

Hi guys!

Attached here is a log file from my current HylaFax implementation.  The 
incoming fax was not received because of an "Unspecified Phase C Error 
etc." I'm on a class 2.0 of USR V.Everthing Courier 56K modem. I would 
very much appreciate your help regarding this. 

Thanks and may the source be with you!

Mike
Jul 24 16:23:22.54: [  939]: SESSION BEGIN 00000115 6324351052
Jul 24 16:23:22.55: [  939]: HylaFAX (tm) Version 4.1.2
Jul 24 16:23:22.55: [  939]: <-- [4:ATA\r]
Jul 24 16:23:54.08: [  939]: --> [4:+FCO]
Jul 24 16:23:54.08: [  939]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jul 24 16:23:54.08: [  939]: RECV FAX: begin
Jul 24 16:23:55.82: [  939]: --> [27:+FTI:"          0533237111"]
Jul 24 16:23:55.82: [  939]: REMOTE TSI "0533237111"
Jul 24 16:23:56.14: [  939]: --> [20:+FCS:0,3,0,2,0,0,0,0]
Jul 24 16:23:56.14: [  939]: REMOTE wants 9600 bit/s
Jul 24 16:23:56.14: [  939]: REMOTE wants page width 1728 pixels in 215 mm
Jul 24 16:23:56.14: [  939]: REMOTE wants unlimited page length 
Jul 24 16:23:56.14: [  939]: REMOTE wants 3.85 line/mm
Jul 24 16:23:56.14: [  939]: REMOTE wants 1-D MR
Jul 24 16:23:56.30: [  939]: --> [2:OK]
Jul 24 16:23:56.30: [  939]: <-- [7:AT+FDR\r]
Jul 24 16:23:58.54: [  939]: --> [20:+FCS:0,3,0,2,0,0,0,0]
Jul 24 16:23:58.54: [  939]: REMOTE wants 9600 bit/s
Jul 24 16:23:58.54: [  939]: REMOTE wants page width 1728 pixels in 215 mm
Jul 24 16:23:58.54: [  939]: REMOTE wants unlimited page length 
Jul 24 16:23:58.54: [  939]: REMOTE wants 3.85 line/mm
Jul 24 16:23:58.54: [  939]: REMOTE wants 1-D MR
Jul 24 16:24:00.04: [  939]: --> [7:CONNECT]
Jul 24 16:24:00.04: [  939]: RECV: begin page
Jul 24 16:24:00.04: [  939]: RECV: send trigger 022
Jul 24 16:24:00.04: [  939]: <-- data [1]
Jul 24 16:24:32.08: [  939]: RECV: 23 total lines, 22 bad lines, 22 consecutive bad lines
Jul 24 16:24:32.08: [  939]: --> [15:+FPS:1,78,0,0,0]
Jul 24 16:24:33.50: [  939]: --> [6:+FET:0]
Jul 24 16:24:33.50: [  939]: RECV recv MPS (more pages, same document)
Jul 24 16:24:33.50: [  939]: --> [2:OK]
Jul 24 16:24:33.50: [  939]: RECV: REJECT page quality, 4% good lines (95% required)
Jul 24 16:24:33.50: [  939]: RECV send RTN (retrain negative)
Jul 24 16:24:33.51: [  939]: <-- [9:AT+FPS=2\r]
Jul 24 16:24:33.65: [  939]: --> [5:ERROR]
Jul 24 16:24:33.65: [  939]: MODEM Command error
Jul 24 16:24:33.65: [  939]: REMOTE HANGUP: Unspecified Phase C error, including too much delay between TCF and +FDR command (code 90)
Jul 24 16:24:33.66: [  939]: RECV FAX (00000115): recvq/fax00089.tif from 0533237111, route to <unspecified>, 0 pages in 0:39
Jul 24 16:24:33.66: [  939]: RECV FAX: Unspecified Phase C error, including too much delay between TCF and +FDR command
Jul 24 16:24:33.66: [  939]: <-- [7:AT+FKS\r]
Jul 24 16:24:35.26: [  939]: --> [7:+FHS:02]
Jul 24 16:24:35.26: [  939]: REMOTE HANGUP: Call aborted,  from +FK or <CAN> (code 2)
Jul 24 16:24:35.26: [  939]: --> [2:OK]
Jul 24 16:24:35.26: [  939]: RECV FAX (00000115): session with 0533237111 terminated abnormally: Unspecified Phase C error, including too much delay between TCF and +FDR command
Jul 24 16:24:35.27: [  939]: RECV FAX: bin/faxrcvd "recvq/fax00089.tif" "ttyS0" "00000115" "Unspecified Phase C error, including too much delay between TCF and +FDR command" "" ""
Jul 24 16:24:35.79: [  939]: RECV FAX: end
Jul 24 16:24:35.80: [  939]: SESSION END