[hylafax-users] have some problem with hylafax

["Le Lang" <lelang@vnmaster.com>]



Dear Sir,

 

Please help me to configuring the hylaxfax program. I want to use hylafax to receiving fax and data.

 

I use Linux RedHat 7.2, hylafax 4.1.2, modem U.S Robotic 56K FAX EXT

 

Right now, I receive data is OK, but fax sometime is OK, sometime can't, it is depend on type of the fax machine. With the new fax machine, it is OK. And with the old, It can't.

 

And it can't receive when they pick up the phone first and listen the fax tone then they press Start button on fax machine. It have error like this: ANSWER: Ring detected without successful handshake

 

I'm forward to your reply.

 

Thank you very much

 

Lang Le

From Saigon, Vietnam

 

PS: This is my configurate file:

 

# $Id: usr-2.0,v 1.6 2001/06/04 05:09:46 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

 

#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:  84
AreaCode:  8
FAXNumber:  +84.8.7155099
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  Medium
GettyArgs:  "-r -b -s %s %l"
LocalIdentifier: "CML Technologies Corp."
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%P of %%T"
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class1  # use class 1 interface
ModemRate:  115200  # DCE-DTE communication rate
ModemFlowControl: rtscts  # XON/XOFF flow control assumed
#
ModemNoFlowCmd:  AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
ModemResultCodesCmd: ATQ0X4  # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd: AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:  AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd: !(0),(0) # override modem response
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC: yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd:       none