[hylafax-users] Receive multiple pages fails

To: hylafax-users@hylafax.org
Subject: [hylafax-users] Receive multiple pages fails
From: Tim Niemueller <tim@niemueller.de>
Reply-To: tim@niemueller.de, ml@niemueller.de
Date: Tue, 15 Jan 2002 20:47:20 +0100

Hi Hylafax users,

I have a Sedlbauer Speed Fax+ ISA ISDN Card which has a DSP to allow 
modem conversation without special drivers.

Now I have configured hylafax on a RedHat machine (pretty up2date with a 
2.4 kernel) as described on sedlbauers homepage at 
http://www.sedlbauer.de/english/kommunikation/linux/RedHat/lredhathyla71.htm

Now I can send faxes (single and multiple pages) but can only receive 
faxes with a single page!

Here is the log of a failed connection. I removed the number:

--- 8< ---

Jan 14 20:52:20.66: [20950]: SESSION BEGIN 00000005 123123123123123
Jan 14 20:52:20.66: [20950]: MODEM set XON/XOFF/FLUSH: input ignored, 
output disabled
Jan 14 20:52:20.66: [20950]: <-- [4:ATA\r]
Jan 14 20:52:25.84: [20950]: --> [7:CONNECT]
Jan 14 20:52:25.84: [20950]: ANSWER: FAX CONNECTION
Jan 14 20:52:25.84: [20950]: MODEM input buffering enabled
Jan 14 20:52:25.84: [20950]: RECV FAX: begin
Jan 14 20:52:25.84: [20950]: MODEM input buffering disabled
Jan 14 20:52:25.84: [20950]: <-- data [23]
Jan 14 20:52:25.84: [20950]: <-- data [2]
Jan 14 20:52:25.88: [20950]: --> [7:CONNECT]
Jan 14 20:52:25.88: [20950]: <-- data [10]
Jan 14 20:52:25.88: [20950]: <-- data [2]
Jan 14 20:52:27.01: [20950]: --> [2:OK]
Jan 14 20:52:27.01: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:52:27.28: [20950]: --> [7:CONNECT]
Jan 14 20:52:28.91: [20950]: --> [2:OK]
Jan 14 20:52:28.91: [20950]: REMOTE TSI "+123123123123213213"
Jan 14 20:52:28.91: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:52:28.92: [20950]: --> [7:CONNECT]
Jan 14 20:52:29.64: [20950]: --> [2:OK]
Jan 14 20:52:29.64: [20950]: REMOTE wants 14400 bit/s
Jan 14 20:52:29.64: [20950]: REMOTE wants page width 1728 pixels in 215 mm
Jan 14 20:52:29.64: [20950]: REMOTE wants A4 page length (297 mm)
Jan 14 20:52:29.64: [20950]: REMOTE wants 7.7 line/mm
Jan 14 20:52:29.64: [20950]: REMOTE wants 2-D MR
Jan 14 20:52:29.64: [20950]: RECV training at v.17 14400 bit/s
Jan 14 20:52:29.64: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output generated
Jan 14 20:52:29.64: [20950]: <-- [11:AT+FRM=145\r]
Jan 14 20:52:31.19: [20950]: --> [7:CONNECT]
Jan 14 20:52:32.88: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jan 14 20:52:32.88: [20950]: RECV: TCF 3035 bytes, 6% non-zero, 2699 
zero-run
Jan 14 20:52:32.88: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:32.88: [20950]: DELAY 75 ms
Jan 14 20:52:32.96: [20950]: <-- [9:AT+FTH=3\r]
Jan 14 20:52:34.59: [20950]: --> [7:CONNECT]
Jan 14 20:52:34.59: [20950]: <-- data [3]
Jan 14 20:52:34.59: [20950]: <-- data [2]
Jan 14 20:52:34.85: [20950]: --> [2:OK]
Jan 14 20:52:34.85: [20950]: TRAINING succeeded
Jan 14 20:52:34.85: [20950]: MODEM input buffering enabled
Jan 14 20:52:34.85: [20950]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jan 14 20:52:34.85: [20950]: <-- [11:AT+FRM=146\r]
Jan 14 20:52:35.41: [20950]: --> [7:CONNECT]
Jan 14 20:52:35.41: [20950]: RECV: begin page
Jan 14 20:52:47.59: [20950]: RECV: 2354 total lines, 0 bad lines, 0 
consecutive bad lines
Jan 14 20:52:47.59: [20950]: RECV: end page
Jan 14 20:52:47.59: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:47.59: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jan 14 20:52:47.59: [20950]: MODEM input buffering disabled
Jan 14 20:52:47.59: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:52:47.73: [20950]: --> [7:CONNECT]
Jan 14 20:52:48.83: [20950]: --> [2:OK]
Jan 14 20:52:48.83: [20950]: RECV recv MPS (more pages, same document)
Jan 14 20:52:48.83: [20950]: DELAY 150 ms
Jan 14 20:52:48.98: [20950]: <-- [9:AT+FTH=3\r]
Jan 14 20:52:48.98: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:48.98: [20950]: RECV send MCF (message confirmation)
Jan 14 20:52:48.98: [20950]: RECV FAX (00000005): from +123123123123213, 
page 1 in 0:14, A4, 7.7 line/mm, 2-D MR, 14400 bit/s
Jan 14 20:52:48.98: [20950]: MODEM input buffering enabled
Jan 14 20:52:48.98: [20950]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jan 14 20:52:48.98: [20950]: <-- [11:AT+FRM=146\r]
Jan 14 20:52:52.20: [20950]: --> [7:CONNECT]
Jan 14 20:52:52.20: [20950]: RECV: begin page
Jan 14 20:52:52.20: [20950]: RECV: 0 total lines, 0 bad lines, 0 
consecutive bad lines
Jan 14 20:52:52.20: [20950]: RECV: end page
Jan 14 20:52:52.20: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:52.20: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jan 14 20:52:52.20: [20950]: MODEM input buffering disabled
Jan 14 20:52:52.20: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:52:52.24: [20950]: --> [7:CONNECT]
Jan 14 20:52:53.21: [20950]: --> [2:OK]
Jan 14 20:52:53.21: [20950]: RECV recv MPS (more pages, same document)
Jan 14 20:52:53.21: [20950]: DELAY 150 ms
Jan 14 20:52:53.36: [20950]: <-- [9:AT+FTH=3\r]
Jan 14 20:52:53.36: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:53.36: [20950]: RECV send MCF (message confirmation)
Jan 14 20:52:53.36: [20950]: RECV FAX (00000005): from +123123123213213, 
page 2 in 0:05, A4, 7.7 line/mm, 2-D MR, 14400 bit/s
Jan 14 20:52:53.36: [20950]: MODEM input buffering enabled
Jan 14 20:52:53.36: [20950]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jan 14 20:52:53.36: [20950]: <-- [11:AT+FRM=146\r]
Jan 14 20:52:56.70: [20950]: --> [7:CONNECT]
Jan 14 20:52:56.70: [20950]: RECV: begin page
Jan 14 20:52:56.70: [20950]: RECV: 0 total lines, 0 bad lines, 0 
consecutive bad lines
Jan 14 20:52:56.70: [20950]: RECV: end page
Jan 14 20:52:56.70: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:56.70: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jan 14 20:52:56.70: [20950]: MODEM input buffering disabled
Jan 14 20:52:56.70: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:52:56.73: [20950]: --> [7:CONNECT]
Jan 14 20:52:57.58: [20950]: --> [2:OK]
Jan 14 20:52:57.58: [20950]: RECV recv MPS (more pages, same document)
Jan 14 20:52:57.58: [20950]: DELAY 150 ms
Jan 14 20:52:57.73: [20950]: <-- [9:AT+FTH=3\r]
Jan 14 20:52:57.73: [20950]: --> [10:NO CARRIER]
Jan 14 20:52:57.73: [20950]: RECV send MCF (message confirmation)
Jan 14 20:52:57.73: [20950]: RECV FAX (00000005): from +123123123213, 
page 3 in 0:04, A4, 7.7 line/mm, 2-D MR, 14400 bit/s
Jan 14 20:52:57.73: [20950]: MODEM input buffering enabled
Jan 14 20:52:57.73: [20950]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jan 14 20:52:57.73: [20950]: <-- [11:AT+FRM=146\r]
Jan 14 20:53:01.36: [20950]: --> [7:CONNECT]
Jan 14 20:53:01.36: [20950]: RECV: begin page
Jan 14 20:53:01.36: [20950]: RECV: 0 total lines, 0 bad lines, 0 
consecutive bad lines
Jan 14 20:53:01.36: [20950]: RECV: end page
Jan 14 20:53:01.36: [20950]: --> [10:NO CARRIER]
Jan 14 20:53:01.36: [20950]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jan 14 20:53:01.36: [20950]: MODEM input buffering disabled
Jan 14 20:53:01.36: [20950]: <-- [9:AT+FRH=3\r]
Jan 14 20:53:01.40: [20950]: --> [7:CONNECT]
Jan 14 20:53:02.12: [20950]: --> [2:OK]
Jan 14 20:53:02.12: [20950]: RECV recv DCN
Jan 14 20:53:02.12: [20950]: RECV FAX (00000005): recvq/fax00003.tif 
from +123123123123, route to <unspecified>, 3 pages in 0:37
Jan 14 20:53:02.12: [20950]: RECV FAX: COMREC received DCN
Jan 14 20:53:02.12: [20950]: <-- [9:AT+FTH=3\r]
Jan 14 20:53:02.68: [20950]: --> [10:NO CARRIER]
Jan 14 20:53:02.68: [20950]: MODEM input buffering enabled
Jan 14 20:53:02.68: [20950]: MODEM input buffering enabled
Jan 14 20:53:02.68: [20950]: RECV FAX (00000005): session with 
+123123123 terminated abnormally: COMREC received DCN
Jan 14 20:53:02.68: [20950]: RECV FAX: bin/faxrcvd "recvq/fax00003.tif" 
"modem" "00000005" "COMREC received DCN"
Jan 14 20:53:03.03: [20950]: RECV FAX: end
Jan 14 20:53:03.03: [20950]: SESSION END

--- 8< ---

As you can see the connection was just aborted. But what does "COMREC 
received DCN" mean? Any idea how I can solve this problem?

Thanks,

	Tim


-- 
     Tim Niemueller <tim@niemueller.de>      www.niemueller.de
=================================================================
  Imagination is more important than knowledge. (Albert Einstein)



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null

Follow-Ups:
- Re: [hylafax-users] Receive multiple pages fails
  - From: Lee Howard

Prev by Date: [hylafax-users] RE FAX--> Mail
Next by Date: Re: [hylafax-users] Hylafax doesn't honor requested permissions
Previous by thread: [hylafax-users] RE FAX--> Mail
Next by thread: Re: [hylafax-users] Receive multiple pages fails
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services