[hylafax-users] Strange behavious

[Jean-Christophe ARNU <jc.arnu@wanadoo.fr>]

Hi all,
	I might be wrong posting my problem here... But I was not able to find
it in the FAQ and into the HowTO/Setup...

	My system is a Linux Mandrake 8.0, an SMP PIII Xeon.... well and a USR
Sporster Voice 33.6k.

	I would like to receive fax and Ppp data. I configured all on ttyS1.I
have FaxGetty running through init which route quite well ppp incoming
calls through mgetty. But as I would like to receive faxes, the modem
hangs on, start to handshake but still stop with a caracteristic beeeeee
noise no fax is received. I was not able to find the problem in my
config. I tried to make a _basic_ fax receiver but the problem
remains....


	What should I do to solve the problem....

Thanks!

	You can find the fax basic receiver configuration  here :

#France
CountryCode:            33
#Midi Pyrenees
AreaCode:               5
#Phone number
FAXNumber:              +33.05.61005644
#France Telecom
LongDistancePrefix:     0
#International
InternationalPrefix:    00
#well as they say in configuration guidelines
DialStringRules:        etc/dialrules.europe
#defaults
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
#----------------------------
RingsBeforeAnswer:      1
#want to here it
SpeakerVolume:          quiet
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow
control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)ModemResultCodesCmd:    ATQ0X4          # enable extended result
codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC:  yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd:       none


-- 
Jean-Christophe ARNU
s/w developer 
Paratronic France



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null