|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] zyxel u-1496e config
--
>Here. Try this (attached). Send me the session logs from two consecutive
>attempts.
Lee thanks for the rpm. I installed rpm and sent some test faxes looks
great
sent about 6 faxes to different numbers all went, tried to fax you but it
gave me a No carrier detected error.
Here are the logs you asked for.
thanks for the help :-)
Dan
Aug 30 10:01:07.97: [ 1084]: SESSION BEGIN 00000034 12149728694975
Aug 30 10:01:07.97: [ 1084]: HylaFAX (tm) Version 4.1
Aug 30 10:01:07.97: [ 1084]: SEND FAX: JOB 20 DEST xxx-xxx-xxxx COMMID
00000034
Aug 30 10:01:07.97: [ 1084]: DEVICE '/dev/ttyS0'
Aug 30 10:01:07.97: [ 1084]: MODEM set DTR OFF
Aug 30 10:01:07.97: [ 1084]: DELAY 75 ms
Aug 30 10:01:08.05: [ 1084]: MODEM set DTR ON
Aug 30 10:01:08.05: [ 1084]: DELAY 2600 ms
Aug 30 10:01:10.65: [ 1084]: MODEM set baud rate: 38400 baud, input flow
RTS/CTS, output flow RTS/CTS
Aug 30 10:01:10.65: [ 1084]: MODEM flush i/o
Aug 30 10:01:10.65: [ 1084]: <-- [4:ATZ\r]
Aug 30 10:01:10.86: [ 1084]: --> [2:OK]
Aug 30 10:01:10.86: [ 1084]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:01:10.88: [ 1084]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:01:10.88: [ 1084]: --> [2:OK]
Aug 30 10:01:10.88: [ 1084]: <-- [5:ATE0\r]
Aug 30 10:01:10.89: [ 1084]: --> [4:ATE0]
Aug 30 10:01:10.89: [ 1084]: --> [2:OK]
Aug 30 10:01:10.89: [ 1084]: <-- [5:ATV1\r]
Aug 30 10:01:10.90: [ 1084]: --> [2:OK]
Aug 30 10:01:10.90: [ 1084]: <-- [5:ATQ0\r]
Aug 30 10:01:10.91: [ 1084]: --> [2:OK]
Aug 30 10:01:10.91: [ 1084]: <-- [7:ATS0=0\r]
Aug 30 10:01:10.92: [ 1084]: --> [2:OK]
Aug 30 10:01:10.92: [ 1084]: <-- [7:ATS8=2\r]
Aug 30 10:01:10.93: [ 1084]: --> [2:OK]
Aug 30 10:01:10.93: [ 1084]: <-- [8:ATS7=60\r]
Aug 30 10:01:10.94: [ 1084]: --> [2:OK]
Aug 30 10:01:10.94: [ 1084]: <-- [6:AT&H3\r]
Aug 30 10:01:10.95: [ 1084]: --> [2:OK]
Aug 30 10:01:10.95: [ 1084]: <-- [6:AT&D2\r]
Aug 30 10:01:10.96: [ 1084]: --> [2:OK]
Aug 30 10:01:10.96: [ 1084]: <-- [6:AT&C1\r]
Aug 30 10:01:10.97: [ 1084]: --> [2:OK]
Aug 30 10:01:10.97: [ 1084]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:01:11.09: [ 1084]: --> [2:OK]
Aug 30 10:01:11.09: [ 1084]: <-- [9:AT+FAA=1\r]
Aug 30 10:01:11.10: [ 1084]: --> [2:OK]
Aug 30 10:01:11.10: [ 1084]: <-- [7:ATM1L1\r]
Aug 30 10:01:11.11: [ 1084]: --> [2:OK]
Aug 30 10:01:11.11: [ 1084]: STATE CHANGE: RUNNING -> SENDING
Aug 30 10:01:11.11: [ 1084]: MODEM input buffering enabled
Aug 30 10:01:11.11: [ 1084]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:01:11.34: [ 1084]: --> [2:OK]
Aug 30 10:01:11.34: [ 1084]: DIAL 9728694975
Aug 30 10:01:11.34: [ 1084]: <-- [15:ATDT9728694975\r]
Aug 30 10:01:32.45: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:32.45: [ 1084]: MODEM input buffering disabled
Aug 30 10:01:34.42: [ 1084]: --> HDLC<38:FF C0 04 00 00 8C 00 77 1D 22 61 B0
BB 00 00 BB BB 00 00 BB BB BB BB BB 80 10 0C 20 08 20 90 B7 C4 09 00 00 2F
80>
Aug 30 10:01:34.42: [ 1084]: --> [2:OK]
Aug 30 10:01:34.42: [ 1084]: REMOTE NSF "00 00 31 00 EE B8 44 86 0D DD 00 00
DD DD 00 00 DD DD DD DD DD 01 08 30 04 10 04 09 ED 23 90 00 00 F4 01 FF"
Aug 30 10:01:34.42: [ 1084]: NSF remote fax equipment: Sharp/Olivetti
Aug 30 10:01:34.42: [ 1084]: NSF remote station ID: "YYYYY"
Aug 30 10:01:34.42: [ 1084]: <-- [9:AT+FRH=3\r]
Aug 30 10:01:34.44: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:35.12: [ 1084]: --> HDLC<23:FF C0 02 4C 6C 6C 9C 04 8C 6C AC 04
2C 8C 4C 04 04 04 04 04 04 04 04>
Aug 30 10:01:35.12: [ 1084]: --> [2:OK]
Aug 30 10:01:35.12: [ 1084]: REMOTE CSI "214 561 9662"
Aug 30 10:01:35.12: [ 1084]: <-- [9:AT+FRH=3\r]
Aug 30 10:01:35.14: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:35.39: [ 1084]: --> HDLC<7:FF C8 01 00 77 1D 22>
Aug 30 10:01:35.39: [ 1084]: --> [2:OK]
Aug 30 10:01:35.39: [ 1084]: REMOTE best rate 14400 bit/s
Aug 30 10:01:35.39: [ 1084]: REMOTE max page width 1728 pixels in 215 mm
Aug 30 10:01:35.39: [ 1084]: REMOTE max unlimited page length
Aug 30 10:01:35.39: [ 1084]: REMOTE best vres 7.7 line/mm
Aug 30 10:01:35.39: [ 1084]: REMOTE best format 2-D MMR
Aug 30 10:01:35.39: [ 1084]: REMOTE supports T.30 Annex A, ECM
Aug 30 10:01:35.39: [ 1084]: REMOTE best 20 ms, 10 ms/scanline
Aug 30 10:01:35.39: [ 1084]: USE 14400 bit/s
Aug 30 10:01:35.39: [ 1084]: USE 20 ms, 10 ms/scanline
Aug 30 10:01:35.39: [ 1084]: SEND file "docq/doc21.ps;40"
Aug 30 10:01:35.39: [ 1084]: USE page width 1728 pixels in 215 mm
Aug 30 10:01:35.39: [ 1084]: USE unlimited page length
Aug 30 10:01:35.39: [ 1084]: USE 3.85 line/mm
Aug 30 10:01:35.39: [ 1084]: USE 2-D MR
Aug 30 10:01:35.39: [ 1084]: SEND training at v.17 14400 bit/s
Aug 30 10:01:35.39: [ 1084]: <-- [9:AT+FTH=3\r]
Aug 30 10:01:35.41: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:35.41: [ 1084]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Aug 30 10:01:35.41: [ 1084]: <-- data [23]
Aug 30 10:01:35.41: [ 1084]: <-- data [2]
Aug 30 10:01:37.13: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:37.13: [ 1084]: <-- HDLC<6:FF C8 C1 00 45 10>
Aug 30 10:01:37.13: [ 1084]: <-- data [6]
Aug 30 10:01:37.13: [ 1084]: <-- data [2]
Aug 30 10:01:37.46: [ 1084]: --> [2:OK]
Aug 30 10:01:37.46: [ 1084]: DELAY 75 ms
Aug 30 10:01:37.54: [ 1084]: <-- [11:AT+FTM=145\r]
Aug 30 10:01:37.56: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:37.56: [ 1084]: <-- data [1024]
Aug 30 10:01:37.56: [ 1084]: <-- data [1024]
Aug 30 10:01:37.56: [ 1084]: <-- data [652]
Aug 30 10:01:37.56: [ 1084]: <-- data [2]
Aug 30 10:01:40.70: [ 1084]: --> [2:OK]
Aug 30 10:01:40.70: [ 1084]: <-- [9:AT+FRH=3\r]
Aug 30 10:01:40.90: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:41.92: [ 1084]: --> HDLC<3:FF C8 21>
Aug 30 10:01:41.92: [ 1084]: --> [2:OK]
Aug 30 10:01:41.92: [ 1084]: TRAINING succeeded
Aug 30 10:01:41.92: [ 1084]: DELAY 75 ms
Aug 30 10:01:42.00: [ 1084]: <-- [11:AT+FTM=146\r]
Aug 30 10:01:42.02: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:42.02: [ 1084]: SEND begin page
Aug 30 10:01:42.02: [ 1084]: <-- data [1025]
Aug 30 10:01:42.02: [ 1084]: <-- data [1024]
Aug 30 10:01:42.02: [ 1084]: <-- data [1024]
Aug 30 10:01:42.02: [ 1084]: <-- data [1024]
Aug 30 10:01:42.02: [ 1084]: <-- data [1024]
Aug 30 10:01:43.02: [ 1084]: <-- data [1024]
Aug 30 10:01:43.02: [ 1084]: <-- data [830]
Aug 30 10:01:43.02: [ 1084]: SENT 6970 bytes of data
Aug 30 10:01:43.02: [ 1084]: SEND 2D RTC
Aug 30 10:01:43.02: [ 1084]: <-- data [30]
Aug 30 10:01:43.02: [ 1084]: <-- data [2]
Aug 30 10:01:43.02: [ 1084]: SEND end page
Aug 30 10:01:46.34: [ 1084]: --> [2:]
Aug 30 10:01:46.34: [ 1084]: --> [2:OK]
Aug 30 10:01:46.34: [ 1084]: DELAY 200 ms
Aug 30 10:01:46.54: [ 1084]: SEND send EOP (no more pages or documents)
Aug 30 10:01:46.54: [ 1084]: <-- [9:AT+FTH=3\r]
Aug 30 10:01:46.56: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:46.56: [ 1084]: <-- HDLC<3:FF C8 F4>
Aug 30 10:01:46.56: [ 1084]: <-- data [3]
Aug 30 10:01:46.56: [ 1084]: <-- data [2]
Aug 30 10:01:47.80: [ 1084]: --> [2:OK]
Aug 30 10:01:47.80: [ 1084]: <-- [9:AT+FRH=3\r]
Aug 30 10:01:48.00: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:49.08: [ 1084]: --> HDLC<3:FF C8 31>
Aug 30 10:01:49.08: [ 1084]: --> [2:OK]
Aug 30 10:01:49.08: [ 1084]: SEND recv MCF (message confirmation)
Aug 30 10:01:49.08: [ 1084]: SEND FAX (00000034): FROM dwright@spca.org TO
xxx-xxxx-xxxx(page 1 of 1 sent in 0:14)
Aug 30 10:01:49.08: [ 1084]: SEND FAX (00000034): FROM dwright@spca.org TO
xxx-xxx-xxxx (docq/doc21.ps;40 sent in 0:14)
Aug 30 10:01:49.08: [ 1084]: <-- [9:AT+FTH=3\r]
Aug 30 10:01:49.10: [ 1084]: --> [7:CONNECT]
Aug 30 10:01:49.10: [ 1084]: <-- HDLC<3:FF C8 DF>
Aug 30 10:01:49.10: [ 1084]: <-- data [3]
Aug 30 10:01:49.10: [ 1084]: <-- data [2]
Aug 30 10:01:50.35: [ 1084]: --> [2:OK]
Aug 30 10:01:50.35: [ 1084]: MODEM input buffering enabled
Aug 30 10:01:50.35: [ 1084]: <-- [5:ATH0\r]
Aug 30 10:01:50.86: [ 1084]: --> [2:OK]
Aug 30 10:01:50.86: [ 1084]: MODEM set DTR OFF
Aug 30 10:01:50.86: [ 1084]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 30 10:01:50.86: [ 1084]: SESSION END
Aug 30 10:02:58.59: [ 1141]: SESSION BEGIN 00000035 12149727167835
Aug 30 10:02:58.59: [ 1141]: HylaFAX (tm) Version 4.1
Aug 30 10:02:58.59: [ 1141]: SEND FAX: JOB 21 DEST xxx-xx-xxxx COMMID
00000035
Aug 30 10:02:58.59: [ 1141]: DEVICE '/dev/ttyS0'
Aug 30 10:02:58.59: [ 1141]: MODEM set DTR OFF
Aug 30 10:02:58.59: [ 1141]: DELAY 75 ms
Aug 30 10:02:58.67: [ 1141]: MODEM set DTR ON
Aug 30 10:02:58.67: [ 1141]: DELAY 2600 ms
Aug 30 10:03:01.27: [ 1141]: MODEM set baud rate: 38400 baud, input flow
RTS/CTS, output flow RTS/CTS
Aug 30 10:03:01.27: [ 1141]: MODEM flush i/o
Aug 30 10:03:01.27: [ 1141]: <-- [4:ATZ\r]
Aug 30 10:03:01.48: [ 1141]: --> [2:OK]
Aug 30 10:03:01.48: [ 1141]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:03:01.50: [ 1141]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:03:01.50: [ 1141]: --> [2:OK]
Aug 30 10:03:01.50: [ 1141]: <-- [5:ATE0\r]
Aug 30 10:03:01.51: [ 1141]: --> [4:ATE0]
Aug 30 10:03:01.51: [ 1141]: --> [2:OK]
Aug 30 10:03:01.51: [ 1141]: <-- [5:ATV1\r]
Aug 30 10:03:01.52: [ 1141]: --> [2:OK]
Aug 30 10:03:01.52: [ 1141]: <-- [5:ATQ0\r]
Aug 30 10:03:01.53: [ 1141]: --> [2:OK]
Aug 30 10:03:01.53: [ 1141]: <-- [7:ATS0=0\r]
Aug 30 10:03:01.54: [ 1141]: --> [2:OK]
Aug 30 10:03:01.54: [ 1141]: <-- [7:ATS8=2\r]
Aug 30 10:03:01.55: [ 1141]: --> [2:OK]
Aug 30 10:03:01.55: [ 1141]: <-- [8:ATS7=60\r]
Aug 30 10:03:01.56: [ 1141]: --> [2:OK]
Aug 30 10:03:01.56: [ 1141]: <-- [6:AT&H3\r]
Aug 30 10:03:01.57: [ 1141]: --> [2:OK]
Aug 30 10:03:01.57: [ 1141]: <-- [6:AT&D2\r]
Aug 30 10:03:01.58: [ 1141]: --> [2:OK]
Aug 30 10:03:01.58: [ 1141]: <-- [6:AT&C1\r]
Aug 30 10:03:01.59: [ 1141]: --> [2:OK]
Aug 30 10:03:01.59: [ 1141]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:03:01.71: [ 1141]: --> [2:OK]
Aug 30 10:03:01.71: [ 1141]: <-- [9:AT+FAA=1\r]
Aug 30 10:03:01.72: [ 1141]: --> [2:OK]
Aug 30 10:03:01.72: [ 1141]: <-- [7:ATM1L1\r]
Aug 30 10:03:01.73: [ 1141]: --> [2:OK]
Aug 30 10:03:01.73: [ 1141]: STATE CHANGE: RUNNING -> SENDING
Aug 30 10:03:01.73: [ 1141]: MODEM input buffering enabled
Aug 30 10:03:01.73: [ 1141]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:03:01.96: [ 1141]: --> [2:OK]
Aug 30 10:03:01.96: [ 1141]: DIAL 9727167835
Aug 30 10:03:01.96: [ 1141]: <-- [15:ATDT9727167835\r]
Aug 30 10:03:24.94: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:24.94: [ 1141]: MODEM input buffering disabled
Aug 30 10:03:27.02: [ 1141]: --> HDLC<43:FF C0 04 00 00 9E 00 00 00 69 F0 90
C8 00 08 00 48 A9 03 0B 1F 01 82 80 92 40 9C EC 4C EC 8C 6C EC 1C CC AC 04
04 04 04 04 04 C0>
Aug 30 10:03:27.03: [ 1141]: --> [2:OK]
Aug 30 10:03:27.03: [ 1141]: REMOTE NSF "00 00 79 00 00 00 96 0F 09 13 00 10
00 12 95 C0 D0 F8 80 41 01 49 02 39 37 32 37 31 36 37 38 33 35 20 20 20 20
20 20 03 FD"
Aug 30 10:03:27.03: [ 1141]: NSF remote fax equipment: Panasonic
Aug 30 10:03:27.03: [ 1141]: NSF remote station ID: "9727167835 "
Aug 30 10:03:27.03: [ 1141]: <-- [9:AT+FRH=3\r]
Aug 30 10:03:27.05: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:27.72: [ 1141]: --> HDLC<23:FF C0 02 AC CC 1C EC 6C 8C EC 4C EC
9C 9C 04 04 04 04 04 04 04 04 04>
Aug 30 10:03:27.72: [ 1141]: --> [2:OK]
Aug 30 10:03:27.72: [ 1141]: REMOTE CSI "99727167835"
Aug 30 10:03:27.72: [ 1141]: <-- [9:AT+FRH=3\r]
Aug 30 10:03:27.74: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:28.05: [ 1141]: --> HDLC<9:FF C8 01 04 77 1F 23 01 88>
Aug 30 10:03:28.05: [ 1141]: --> [2:OK]
Aug 30 10:03:28.05: [ 1141]: REMOTE best rate 14400 bit/s
Aug 30 10:03:28.05: [ 1141]: REMOTE max page width 1728 pixels in 215 mm
Aug 30 10:03:28.05: [ 1141]: REMOTE max unlimited page length
Aug 30 10:03:28.05: [ 1141]: REMOTE best vres 7.7 line/mm
Aug 30 10:03:28.05: [ 1141]: REMOTE best format 2-D MMR
Aug 30 10:03:28.05: [ 1141]: REMOTE supports T.30 Annex A, ECM
Aug 30 10:03:28.05: [ 1141]: REMOTE best 0 ms/scanline
Aug 30 10:03:28.05: [ 1141]: USE 14400 bit/s
Aug 30 10:03:28.05: [ 1141]: USE 0 ms/scanline
Aug 30 10:03:28.05: [ 1141]: SEND file "docq/doc22.ps;00"
Aug 30 10:03:28.05: [ 1141]: USE page width 1728 pixels in 215 mm
Aug 30 10:03:28.05: [ 1141]: USE unlimited page length
Aug 30 10:03:28.05: [ 1141]: USE 3.85 line/mm
Aug 30 10:03:28.05: [ 1141]: USE 1-D MR
Aug 30 10:03:28.05: [ 1141]: SEND training at v.17 14400 bit/s
Aug 30 10:03:28.05: [ 1141]: <-- [9:AT+FTH=3\r]
Aug 30 10:03:28.07: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:28.07: [ 1141]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Aug 30 10:03:28.07: [ 1141]: <-- data [23]
Aug 30 10:03:28.07: [ 1141]: <-- data [2]
Aug 30 10:03:29.79: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:29.79: [ 1141]: <-- HDLC<6:FF C8 C1 00 44 1E>
Aug 30 10:03:29.79: [ 1141]: <-- data [6]
Aug 30 10:03:29.79: [ 1141]: <-- data [2]
Aug 30 10:03:30.12: [ 1141]: --> [2:OK]
Aug 30 10:03:30.12: [ 1141]: DELAY 75 ms
Aug 30 10:03:30.20: [ 1141]: <-- [11:AT+FTM=145\r]
Aug 30 10:03:30.22: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:30.22: [ 1141]: <-- data [1024]
Aug 30 10:03:30.22: [ 1141]: <-- data [1024]
Aug 30 10:03:30.22: [ 1141]: <-- data [652]
Aug 30 10:03:30.22: [ 1141]: <-- data [2]
Aug 30 10:03:33.36: [ 1141]: --> [2:OK]
Aug 30 10:03:33.36: [ 1141]: <-- [9:AT+FRH=3\r]
Aug 30 10:03:34.10: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:35.20: [ 1141]: --> HDLC<3:FF C8 21>
Aug 30 10:03:35.20: [ 1141]: --> [2:OK]
Aug 30 10:03:35.20: [ 1141]: TRAINING succeeded
Aug 30 10:03:35.20: [ 1141]: DELAY 75 ms
Aug 30 10:03:35.28: [ 1141]: <-- [11:AT+FTM=146\r]
Aug 30 10:03:35.30: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:35.30: [ 1141]: SEND begin page
Aug 30 10:03:35.30: [ 1141]: <-- data [1026]
Aug 30 10:03:35.30: [ 1141]: <-- data [523]
Aug 30 10:03:35.30: [ 1141]: SENT 1526 bytes of data
Aug 30 10:03:35.30: [ 1141]: SEND 1D RTC
Aug 30 10:03:35.30: [ 1141]: <-- data [29]
Aug 30 10:03:35.30: [ 1141]: <-- data [2]
Aug 30 10:03:35.30: [ 1141]: SEND end page
Aug 30 10:03:36.60: [ 1141]: --> [2:OK]
Aug 30 10:03:36.60: [ 1141]: DELAY 200 ms
Aug 30 10:03:36.80: [ 1141]: SEND send EOP (no more pages or documents)
Aug 30 10:03:36.80: [ 1141]: <-- [9:AT+FTH=3\r]
Aug 30 10:03:36.82: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:36.82: [ 1141]: <-- HDLC<3:FF C8 F4>
Aug 30 10:03:36.82: [ 1141]: <-- data [3]
Aug 30 10:03:36.82: [ 1141]: <-- data [2]
Aug 30 10:03:38.06: [ 1141]: --> [2:OK]
Aug 30 10:03:38.06: [ 1141]: <-- [9:AT+FRH=3\r]
Aug 30 10:03:38.67: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:39.77: [ 1141]: --> HDLC<3:FF C8 31>
Aug 30 10:03:39.77: [ 1141]: --> [2:OK]
Aug 30 10:03:39.77: [ 1141]: SEND recv MCF (message confirmation)
Aug 30 10:03:39.77: [ 1141]: SEND FAX (00000035): FROM dwright@spca.org
TOxxx-xxx-xxxx (page 1 of 1 sent in 0:11)
Aug 30 10:03:39.77: [ 1141]: SEND FAX (00000035): FROM dwright@spca.org TO
xxx-xxx-xxxx(docq/doc22.ps;00 sent in 0:11)
Aug 30 10:03:39.77: [ 1141]: <-- [9:AT+FTH=3\r]
Aug 30 10:03:39.79: [ 1141]: --> [7:CONNECT]
Aug 30 10:03:39.79: [ 1141]: <-- HDLC<3:FF C8 DF>
Aug 30 10:03:39.79: [ 1141]: <-- data [3]
Aug 30 10:03:39.79: [ 1141]: <-- data [2]
Aug 30 10:03:41.04: [ 1141]: --> [2:OK]
Aug 30 10:03:41.04: [ 1141]: MODEM input buffering enabled
Aug 30 10:03:41.04: [ 1141]: <-- [5:ATH0\r]
Aug 30 10:03:41.55: [ 1141]: --> [2:OK]
Aug 30 10:03:41.55: [ 1141]: MODEM set DTR OFF
Aug 30 10:03:41.55: [ 1141]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 30 10:03:41.55: [ 1141]: SESSION END
ug 30 10:01:07 yesdan FaxSend[1084]: STATE CHANGE: BASE -> RUNNING
Aug 30 10:01:07 yesdan FaxSend[1084]: MODEM input buffering disabled
Aug 30 10:01:07 yesdan FaxSend[1084]: HylaFAX (tm) Version 4.1
Aug 30 10:01:07 yesdan FaxSend[1084]: SEND FAX: JOB 20 DEST xxx-xxx-xxxx
COMMID 00000034
Aug 30 10:01:07 yesdan FaxSend[1084]: DEVICE '/dev/ttyS0'
Aug 30 10:01:50 yesdan FaxQueuer[939]: NOTIFY: bin/notify "doneq/q20" "done"
"0:48"
Aug 30 10:02:05 yesdan FaxGetty[978]: MODEM set DTR OFF
Aug 30 10:02:05 yesdan FaxGetty[978]: DELAY 75 ms
Aug 30 10:02:05 yesdan FaxGetty[978]: MODEM set DTR ON
Aug 30 10:02:05 yesdan FaxGetty[978]: DELAY 2600 ms
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM set baud rate: 38400 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM flush i/o
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [4:ATZ\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATE0\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [4:ATE0]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATV1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATQ0\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATS0=0\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATS8=2\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [8:ATS7=60\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&H3\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&D2\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&C1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=?\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [13:0,1,2,2.0,6,8]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Data"
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 1"
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 2"
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 2.0"
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Voice"
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FMFR?\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [5:ZyXEL]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM: Mfr ZyXEL
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FREV?\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [18:U1496E V 6.22 P ]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM: Revision U1496E V 6.22 P
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FTM=?\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 3.85 line/mm
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 7.7 line/mm
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 2400 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 4800 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 7200 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 9600 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 12000 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 14400 bit/s
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 1728 pixels
in 215 mm
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 2048 pixels
in 255 mm
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 2432 pixels
in 303 mm
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports A4 page length (297 mm)
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports B4 page length (364 mm)
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports unlimited page length
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 1-D MR
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 2-D MR
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 0 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 5 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 10 ms, 5 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 10 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 20 ms, 10 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 20 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 40 ms, 20 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 40 ms/scanline
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FRM=?\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FAA=1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM ZYXEL /U1496E V 6.22 P
Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATM1L1\r]
Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:02:08 yesdan FaxGetty[978]: STATE CHANGE: LOCKWAIT -> RUNNING
Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM input buffering disabled
Aug 30 10:02:53 yesdan FaxSend[1141]: MODEM set DTR OFF
Aug 30 10:02:53 yesdan FaxSend[1141]: DELAY 75 ms
Aug 30 10:02:53 yesdan FaxSend[1141]: MODEM set DTR ON
Aug 30 10:02:53 yesdan FaxSend[1141]: DELAY 2600 ms
Aug 30 10:02:55 yesdan FaxSend[1141]: MODEM set baud rate: 38400 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 30 10:02:55 yesdan FaxSend[1141]: MODEM flush i/o
Aug 30 10:02:55 yesdan FaxSend[1141]: <-- [4:ATZ\r]
Aug 30 10:02:56 yesdan FaxGetty[978]: ANSWER: Can not lock modem device
Aug 30 10:02:56 yesdan FaxGetty[978]: STATE CHANGE: RUNNING -> LOCKWAIT
(timeout 30)
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATE0\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [4:ATE0]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATV1\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATQ0\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [7:ATS0=0\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [7:ATS8=2\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [8:ATS7=60\r]
Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [6:AT&H3\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [6:AT&D2\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [6:AT&C1\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=?\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [13:0,1,2,2.0,6,8]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Data"
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 1"
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 2"
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 2.0"
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Voice"
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FMFR?\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [5:ZyXEL]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM: Mfr ZyXEL
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FREV?\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [18:U1496E V 6.22 P ]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM: Revision U1496E V 6.22 P
Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FTM=?\r]
Aug 30 10:02:57 yesdan FaxSend[1141]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 3.85 line/mm
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 7.7 line/mm
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 2400 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 4800 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 7200 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 9600 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 12000 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 14400 bit/s
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 1728 pixels
in 215 mm
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 2048 pixels
in 255 mm
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 2432 pixels
in 303 mm
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports A4 page length (297 mm)
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports B4 page length (364 mm)
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports unlimited page length
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 1-D MR
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 2-D MR
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 0 ms/scanline
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 5 ms/scanline
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 10 ms, 5 ms/scanline
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 10 ms/scanline
Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 20 ms, 10 ms/scanline
Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 20 ms/scanline
Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 40 ms, 20 ms/scanline
Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 40 ms/scanline
Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [9:AT+FRM=?\r]
Aug 30 10:02:58 yesdan FaxSend[1141]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [9:AT+FAA=1\r]
Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM ZYXEL /U1496E V 6.22 P
Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [7:ATM1L1\r]
Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK]
Aug 30 10:02:58 yesdan FaxSend[1141]: STATE CHANGE: BASE -> RUNNING
Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM input buffering disabled
Aug 30 10:02:58 yesdan FaxSend[1141]: HylaFAX (tm) Version 4.1
Aug 30 10:02:58 yesdan FaxSend[1141]: SEND FAX: JOB 21 DEST xxx-xxx-xxxx
COMMID 00000035
Aug 30 10:02:58 yesdan FaxSend[1141]: DEVICE '/dev/ttyS0'
Aug 30 10:03:41 yesdan FaxQueuer[939]: NOTIFY: bin/notify "doneq/q21" "done"
"0:48"
Aug 30 10:03:56 yesdan FaxGetty[978]: MODEM set DTR OFF
Aug 30 10:03:56 yesdan FaxGetty[978]: DELAY 75 ms
Aug 30 10:03:56 yesdan FaxGetty[978]: MODEM set DTR ON
Aug 30 10:03:56 yesdan FaxGetty[978]: DELAY 2600 ms
Aug 30 10:03:58 yesdan FaxGetty[978]: MODEM set baud rate: 38400 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 30 10:03:58 yesdan FaxGetty[978]: MODEM flush i/o
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [4:ATZ\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATE0\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [4:ATE0]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATV1\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATQ0\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [7:ATS0=0\r]
Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [7:ATS8=2\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [8:ATS7=60\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&H3\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&D2\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&C1\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=?\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [13:0,1,2,2.0,6,8]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Data"
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 1"
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 2"
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 2.0"
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Voice"
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FMFR?\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [5:ZyXEL]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM: Mfr ZyXEL
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FREV?\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [18:U1496E V 6.22 P ]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM: Revision U1496E V 6.22 P
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FTM=?\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 3.85 line/mm
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 7.7 line/mm
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 2400 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 4800 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 7200 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 9600 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 12000 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 14400 bit/s
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 1728 pixels
in 215 mm
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 2048 pixels
in 255 mm
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 2432 pixels
in 303 mm
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports A4 page length (297 mm)
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports B4 page length (364 mm)
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports unlimited page length
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 1-D MR
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 2-D MR
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 0 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 5 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 10 ms, 5 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 10 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 20 ms, 10 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 20 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 40 ms, 20 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 40 ms/scanline
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FRM=?\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FAA=1\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM ZYXEL /U1496E V 6.22 P
Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [7:ATM1L1\r]
Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK]
Aug 30 10:03:59 yesdan FaxGetty[978]: STATE CHANGE: LOCKWAIT -> RUNNING
Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM input buffering disabled
Aug 30 10:04:44 yesdan FaxSend[1155]: MODEM set DTR OFF
Aug 30 10:04:44 yesdan FaxSend[1155]: DELAY 75 ms
Aug 30 10:04:44 yesdan FaxSend[1155]: MODEM set DTR ON
Aug 30 10:04:44 yesdan FaxSend[1155]: DELAY 2600 ms
Aug 30 10:04:46 yesdan FaxSend[1155]: MODEM set baud rate: 38400 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 30 10:04:46 yesdan FaxSend[1155]: MODEM flush i/o
Aug 30 10:04:46 yesdan FaxSend[1155]: <-- [4:ATZ\r]
Aug 30 10:04:47 yesdan FaxGetty[978]: ANSWER: Can not lock modem device
Aug 30 10:04:47 yesdan FaxGetty[978]: STATE CHANGE: RUNNING -> LOCKWAIT
(timeout 30)
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATE0\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [4:ATE0]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATV1\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATQ0\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [7:ATS0=0\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [7:ATS8=2\r]
Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [8:ATS7=60\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&H3\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&D2\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&C1\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=?\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [13:0,1,2,2.0,6,8]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Data"
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 1"
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 2"
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 2.0"
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Voice"
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FMFR?\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [5:ZyXEL]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM: Mfr ZyXEL
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FREV?\r]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [18:U1496E V 6.22 P ]
Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM: Revision U1496E V 6.22 P
Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FTM=?\r]
Aug 30 10:04:49 yesdan FaxSend[1155]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 3.85 line/mm
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 7.7 line/mm
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 2400 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 4800 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 7200 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 9600 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 12000 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 14400 bit/s
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 1728 pixels
in 215 mm
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 2048 pixels
in 255 mm
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 2432 pixels
in 303 mm
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports A4 page length (297 mm)
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports B4 page length (364 mm)
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports unlimited page length
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 1-D MR
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 2-D MR
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 0 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 5 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 10 ms, 5 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 10 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 20 ms, 10 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 20 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 40 ms, 20 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 40 ms/scanline
Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [9:AT+FRM=?\r]
Aug 30 10:04:49 yesdan FaxSend[1155]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=1\r]
Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [9:AT+FAA=1\r]
Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM ZYXEL /U1496E V 6.22 P
Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [7:ATM1L1\r]
Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK]
Aug 30 10:04:49 yesdan FaxSend[1155]: STATE CHANGE: BASE -> RUNNING
Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM input buffering disabled
Aug 30 10:04:49 yesdan FaxSend[1155]: HylaFAX (tm) Version 4.1
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
