|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] faxing from certain senders to me fails, error no carrier!
Normal inboundfax:
May 15 09:35:09.53: [ 827]: SESSION BEGIN 00000329 3589736020
May 15 09:35:09.54: [ 827]: <-- [4:ATA\r]
May 15 09:35:20.06: [ 827]: --> [5:+FCON]
May 15 09:35:20.06: [ 827]: ANSWER: FAX CONNECTION
... and so on
but sometimes
May 10 09:37:47.11: [ 827]: SESSION BEGIN 00000301 3589736020
May 10 09:37:47.12: [ 827]: <-- [4:ATA\r]
May 10 09:37:52.16: [ 827]: --> [10:NO CARRIER]
May 10 09:37:52.16: [ 827]: ANSWER: Ring detected without successful handshake
May 10 09:37:52.16: [ 827]: SESSION END
what's wrong. My or remote fault? Only sertain senders machines.
4.1 beta3 (rpm from hylafax.org) on rh 6.2
My config file:
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemNoFlowCmd: AT\Q0 # disable flow control cmd
ModemSoftFlowCmd: AT\Q1 # software flow control cmd
ModemHardFlowCmd: AT\Q3 # hardware flow control cmd
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
ModemDialCmd: ATDT%s@ #
ModemAnswerCmd: ATA # use this to answer phone
ModemNoAutoAnswerCmd: ATS0=3 # disable auto-answer
ModemAnswerFaxBeginCmd: "<19200><xon>"
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
##
# Configuration parameters for Class 2 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
Class2TBCCmd: AT # setup stream mode
Class2PHCTOCmd: AT # set phase C timeout parameter
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "\022"
Class2XmitWaitForXON: yes # if true, wait for XON before send
Tia Teijo Tykkä
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
