[hylafax-users] AW: config help - UMC 9624,2,E,290E 14.4

["Bernd Proissl" <lists@proissl.de>]

> Von: hylafax-users-bounce@hylafax.org
> 
> Hi everyone.  I'm trying to get an old UMC 9624,2,E,290E 14.4 Modem working
> (it goes under the name of "Exar" or "Aceex" instead of UMC sometimes,
> usually model DM-1496V).
> 
> Does anyone have a functioning config file for this modem?
> 
> It's listed at: 
> http://www.hylafax.org/Scorecard/results/atfmdl.html
> 
> Appropriate mgetty "init" strings are at: 
> http://afaa.asso.fr/linux-doc/mgetty-1.1.14/modems.db
> 
> I thought that it would perhaps work with the 'umc92144' or 'exar'
> prototype config files, but it doesn't.  The 'exar' config can't even
> initialize it, resulting in a "wedged" error.  Using the umc92144
> prototype, the modem initializes and can receive faxes okay, but when
> attempting to send a fax, it results in a "Can not setup modem" error.
> Following is the log on the attempted fax sending.  Can somebody give me a
> pointer on this?  Thanks.
> 
> Lee
> 
> Mar 23 00:26:32.42: [ 6258]: SESSION BEGIN 00000217 14157550959
> Mar 23 00:26:32.42: [ 6258]: SEND FAX: JOB 22 DEST 7550959 COMMID 00000217
> Mar 23 00:26:32.42: [ 6258]: MODEM set DTR OFF
> Mar 23 00:26:32.42: [ 6258]: DELAY 2600 ms
> Mar 23 00:26:35.02: [ 6258]: MODEM set DTR ON
> Mar 23 00:26:35.02: [ 6258]: MODEM set baud rate: 38400 baud, input flow
> RTS/CTS, output flow RTS/CTS
> Mar 23 00:26:35.02: [ 6258]: MODEM flush i/o
> Mar 23 00:26:35.02: [ 6258]: <-- [4:ATZ\r]
> Mar 23 00:26:35.02: [ 6258]: <-- <3:41 54 5A>
> Mar 23 00:26:35.02: [ 6258]: <-- <1:0D>
> Mar 23 00:26:35.29: [ 6258]: --> <6:0D 0A 4F 4B 0D 0A>
> Mar 23 00:26:35.29: [ 6258]: --> [2:OK]
> Mar 23 00:26:35.29: [ 6258]: <-- [15:ATE0V1Q0S0=0H0\r]
> Mar 23 00:26:35.29: [ 6258]: <-- <14:41 54 45 30 56 31 51 30 53 30 3D 30 48
> 30>
> Mar 23 00:26:35.29: [ 6258]: <-- <1:0D>
> Mar 23 00:26:35.30: [ 6258]: --> <15:41 54 45 30 56 31 51 30 53 30 3D 30 48
> 30 0D>
> Mar 23 00:26:35.57: [ 6258]: --> <6:0D 0A 4F 4B 0D 0A>
> Mar 23 00:26:35.57: [ 6258]: --> [14:ATE0V1Q0S0=0H0]
> Mar 23 00:26:35.57: [ 6258]: --> [2:OK]
> Mar 23 00:26:35.57: [ 6258]: <-- [21:ATS8=2S7=60&K3&D2&C1\r]
> Mar 23 00:26:35.57: [ 6258]: <-- <20:41 54 53 38 3D 32 53 37 3D 36 30 26 4B
> 33 26 44 32 26 43 31>
> Mar 23 00:26:35.57: [ 6258]: <-- <1:0D>
just a guess:
try to reduce ATS8=2S7=60&K3&D2&C1 or break it into smaller peaces.
The modem does not answer this command. Maybe it does not understand one of 
these many commands.
(It has been discussed that hylafax should not send sunch long strings to the modem
and better break them up into single ATXXs for better diagnosis in case of problems)

Bernd

> Mar 23 00:26:40.57: [ 6258]: MODEM TIMEOUT: reading line from modem
> Mar 23 00:26:40.57: [ 6258]: MODEM <Timeout>
> Mar 23 00:26:40.57: [ 6258]: SEND FAILED: Can not setup modem
> Mar 23 00:26:40.57: [ 6258]: MODEM set DTR OFF
> Mar 23 00:26:40.57: [ 6258]: STATE CHANGE: RUNNING -> MODEMWAIT (timeout 30)
> Mar 23 00:26:40.57: [ 6258]: SESSION END
> 
> 
> 
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>  To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
> 


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null