[hylafax-users] MT5600ZDX / RH6.1 / HF4.1beta1/ Unspecified Transmit Phase D error

To: hylafax-users@hylafax.org
Subject: [hylafax-users] MT5600ZDX / RH6.1 / HF4.1beta1/ Unspecified Transmit Phase D error
From: "Abrahamsen, Kenneth" <Kenneth_Abrahamsen@mcgraw-hill.com>
Date: Wed, 21 Feb 2001 17:32:37 -0500
[root@twgrh1 etc]# ftp localhost 4559
Connected to localhost.localdomain.
220 twgrh1 server (HylaFAX (tm) Version 4.1beta1) ready.

Using this config for receiving modem ttyS1 (MT5600ZDX):
Sending from ttyS0 to ttyS1 for testing config.ttyS1 and got the following
log errors.
Any clues for a solution would be appreciated.
Thanks.
ken

[root@twgrh1 etc]# cat config.ttyS1
# $Id: mt-5600zdx 2001/02/21 12:00:00 root Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a Multitech 5600ZDX Class 2 modem.
#
# This configuration file sets up the modem to run at 38.4 for
# sending and for receiving.  RTS/CTS is used for flow control
# which also works for data connections.  Adaptive answer support
# is reliable, but to use it you must also enable ModemWaitForConnect
# to force the server to skip intermediate status messages and
# wait for the "CONNECT" message.
#
# CONFIG: CLASS2: MULTITECH 5600ZDX
#
# BEGIN-SERVER
# END-SERVER
CountryCode:            1
AreaCode:               425
FAXNumber:              425-486-7868
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "425-486-7868 (WRIGHT GROUP)"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c - Job %i|Page %%p of %%t"
MaxRecvPages:           9999
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              38400           # lock rate for DCE-DTE
                                        # communication
ModemFlowControl:       rtscts          # default
#
ModemHardFlowCmd:       AT&E4           # hardware flow control
ModemSoftFlowCmd:       AT&E5           # software flow control
ModemSetupDTRCmd:       AT&D3           # setup so DTR drop resets
                                        # modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
                                        # (or not)
ModemSetupAACmd:        AT+FAA=1        # enable adaptive-answer in
                                        # class 2
#
# NB: some models get confused by the @
#
ModemDialCmd:           ATDT%s          # T for tone dialing, @ for
                                        # silence
#
Class2RecvDataTrigger:  "\022"          # character sent to modem to
                                        # start recv
[root@twgrh1 etc]#


Your facsimile job to 3214 was not sent because:
    Unable to transmit page (giving up after 3 attempts)

The job will be retried at 14:23.

    ---- Transcript of session follows ----

Feb 21 14:15:48.74: [21694]: SESSION BEGIN 00001934 14253214
Feb 21 14:15:48.74: [21694]: SEND FAX: JOB 722 DEST 3214 COMMID 00001934
Feb 21 14:15:48.74: [21694]: DELAY 2600 ms
Feb 21 14:15:51.34: [21694]: <-- [18:AT&F2E0V1Q0S0=0H0\r]
Feb 21 14:15:51.50: [21694]: --> [2:OK]
Feb 21 14:15:51.50: [21694]: <-- [21:ATS8=2S7=60&K3&D2&C1\r]
Feb 21 14:15:51.66: [21694]: --> [2:OK]
Feb 21 14:15:51.66: [21694]: <-- [12:AT+FCLASS=2\r]
Feb 21 14:15:51.81: [21694]: --> [2:OK]
Feb 21 14:15:51.81: [21694]: <-- [10:AT+FTBC=0\r]
Feb 21 14:15:51.96: [21694]: --> [2:OK]
Feb 21 14:15:51.96: [21694]: <-- [10:AT+FBOR=0\r]
Feb 21 14:15:52.11: [21694]: --> [2:OK]
Feb 21 14:15:52.11: [21694]: <-- [13:AT+FPHCTO=30\r]
Feb 21 14:15:52.26: [21694]: --> [2:OK]
Feb 21 14:15:52.26: [21694]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Feb 21 14:15:52.42: [21694]: --> [2:OK]
Feb 21 14:15:52.42: [21694]: <-- [5:ATM0\r]
Feb 21 14:15:52.57: [21694]: --> [2:OK]
Feb 21 14:15:52.57: [21694]: <-- [12:AT+FCLASS=2\r]
Feb 21 14:15:52.82: [21694]: --> [2:OK]
Feb 21 14:15:52.82: [21694]: <-- [10:AT+FTBC=0\r]
Feb 21 14:15:53.07: [21694]: --> [2:OK]
Feb 21 14:15:53.07: [21694]: <-- [10:AT+FBOR=0\r]
Feb 21 14:15:53.32: [21694]: --> [2:OK]
Feb 21 14:15:53.32: [21694]: <-- [13:AT+FPHCTO=30\r]
Feb 21 14:15:53.57: [21694]: --> [2:OK]
Feb 21 14:15:53.57: [21694]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Feb 21 14:15:53.83: [21694]: --> [2:OK]
Feb 21 14:15:53.83: [21694]: <-- [31:AT+FLID="425-486-7868 (THE WR"\r]
Feb 21 14:15:54.09: [21694]: --> [2:OK]
Feb 21 14:15:54.10: [21694]: DIAL 3214
Feb 21 14:15:54.10: [21694]: <-- [9:ATDT3214\r]
Feb 21 14:16:07.99: [21694]: --> [5:+FCON]
Feb 21 14:16:09.65: [21694]: --> [29:+FCSI: "425-486-7868 (WRIGHT"]
Feb 21 14:16:09.65: [21694]: REMOTE CSI "425-486-7868 (WRIGHT"
Feb 21 14:16:10.00: [21694]: --> [22:+FDIS: 1,5,2,2,0,0,0,0]
Feb 21 14:16:10.11: [21694]: --> [2:OK]
Feb 21 14:16:10.11: [21694]: REMOTE best rate 14400 bit/s
Feb 21 14:16:10.11: [21694]: REMOTE max page width 2432 pixels in 303 mm
Feb 21 14:16:10.11: [21694]: REMOTE max unlimited page length 
Feb 21 14:16:10.11: [21694]: REMOTE best vres 7.7 line/mm
Feb 21 14:16:10.11: [21694]: REMOTE best format 1-D MR
Feb 21 14:16:10.11: [21694]: REMOTE best 0 ms/scanline
Feb 21 14:16:10.11: [21694]: USE 14400 bit/s
Feb 21 14:16:10.11: [21694]: USE 0 ms/scanline
Feb 21 14:16:10.11: [21694]: SEND file "docq/doc1107.ps;30"
Feb 21 14:16:10.12: [21694]: USE page width 1728 pixels in 215 mm
Feb 21 14:16:10.12: [21694]: USE unlimited page length 
Feb 21 14:16:10.12: [21694]: USE 3.85 line/mm
Feb 21 14:16:10.12: [21694]: USE 1-D MR
Feb 21 14:16:10.12: [21694]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Feb 21 14:16:10.37: [21694]: --> [2:OK]
Feb 21 14:16:10.37: [21694]: <-- [7:AT+FDT\r]
Feb 21 14:16:18.46: [21694]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Feb 21 14:16:18.67: [21694]: --> [7:CONNECT]
Feb 21 14:16:18.67: [21694]: SEND wait for XON
Feb 21 14:16:18.67: [21694]: --> [1:]
Feb 21 14:16:18.67: [21694]: SEND begin page
Feb 21 14:16:35.74: [21694]: SENT 33767 bytes of data
Feb 21 14:16:35.74: [21694]: SEND end page
Feb 21 14:16:38.26: [21694]: --> [2:OK]
Feb 21 14:16:38.26: [21694]: SEND send MPS (more pages, same document)
Feb 21 14:16:38.26: [21694]: <-- [9:AT+FET=0\r]
Feb 21 14:16:41.47: [21694]: --> [8:+FPTS: 2]
Feb 21 14:16:41.58: [21694]: --> [2:OK]
Feb 21 14:16:41.58: [21694]: SEND recv RTN (retrain negative)
Feb 21 14:16:41.58: [21694]: <-- [24:AT+FDIS=0,4,0,2,0,0,0,0\r]
Feb 21 14:16:41.84: [21694]: --> [2:OK]
Feb 21 14:16:41.84: [21694]: <-- [7:AT+FDT\r]
Feb 21 14:16:49.95: [21694]: --> [22:+FDCS: 0,4,0,2,0,0,0,0]
Feb 21 14:16:50.17: [21694]: --> [7:CONNECT]
Feb 21 14:16:50.17: [21694]: SEND wait for XON
Feb 21 14:16:50.17: [21694]: --> [1:]
Feb 21 14:16:50.17: [21694]: SEND begin page
Feb 21 14:17:10.19: [21694]: SENT 33767 bytes of data
Feb 21 14:17:10.19: [21694]: SEND end page
Feb 21 14:17:13.63: [21694]: --> [2:OK]
Feb 21 14:17:13.63: [21694]: SEND send MPS (more pages, same document)
Feb 21 14:17:13.63: [21694]: <-- [9:AT+FET=0\r]
Feb 21 14:17:16.85: [21694]: --> [8:+FPTS: 2]
Feb 21 14:17:16.96: [21694]: --> [2:OK]
Feb 21 14:17:16.96: [21694]: SEND recv RTN (retrain negative)
Feb 21 14:17:16.96: [21694]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,0\r]
Feb 21 14:17:17.22: [21694]: --> [2:OK]
Feb 21 14:17:17.22: [21694]: <-- [7:AT+FDT\r]
Feb 21 14:17:24.21: [21694]: --> [22:+FDCS: 0,3,0,2,0,0,0,0]
Feb 21 14:17:24.43: [21694]: --> [7:CONNECT]
Feb 21 14:17:24.43: [21694]: SEND wait for XON
Feb 21 14:17:24.43: [21694]: --> [1:]
Feb 21 14:17:24.43: [21694]: SEND begin page
Feb 21 14:17:49.07: [21694]: SENT 33767 bytes of data
Feb 21 14:17:49.07: [21694]: SEND end page
Feb 21 14:17:53.70: [21694]: --> [2:OK]
Feb 21 14:17:53.70: [21694]: SEND send MPS (more pages, same document)
Feb 21 14:17:53.70: [21694]: <-- [9:AT+FET=0\r]
Feb 21 14:17:56.94: [21694]: --> [8:+FPTS: 2]
Feb 21 14:17:57.05: [21694]: --> [2:OK]
Feb 21 14:17:57.05: [21694]: SEND recv RTN (retrain negative)
Feb 21 14:17:57.05: [21694]: <-- [6:AT+FK\r]
Feb 21 14:18:02.75: [21694]: --> [9:+FHNG: 50]
Feb 21 14:18:02.75: [21694]: REMOTE HANGUP: Unspecified Transmit Phase D
error, including +FPHCTO timeout between data and +FET command (code 50)
Feb 21 14:18:03.75: [21694]: --> [2:OK]
Feb 21 14:18:03.75: [21694]: <-- [5:ATH0\r]
Feb 21 14:18:04.00: [21694]: --> [2:OK]
Feb 21 14:18:04.00: [21694]: SESSION END


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
Prev by Date: [hylafax-users] Sendpage Paging problems
Next by Date: Re: [hylafax-users] Fresh system admin needs help - RH 6.2 + Hyla fax-4.1beta2-8rh6.i386.rpm
Prev by thread: [hylafax-users] Sendpage Paging problems
Next by thread: [hylafax-users] Problem with Zyxel Omni 56K
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services