Re: [hylafax-users] Weired problem sending faxes!

[Lee Howard <faxguy@deanox.com>]

At 08:44 PM 11/30/00 +0100, Marco Goebenich wrote:

>If this error does not happen to you show me please your config file.

Happens all the time here with no problems.  I have employees fax to voice
numbers constantly (accidentally).  You may want to try removing the @ at
the end of your ModemDialCmd.

Here's my config.ttyS1 file:

Lee.

# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		435
FAXNumber:		435-755-0959
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		0xFFF
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Deanox, Inc."
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              38400           # max rate for DCE-DTE communication
ModemFlowControl:       rtscts          # hardware flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0&H1&I0&R2    # leave modem in class 0
ModemAnswerCmd:         AT+FCLASS=1&H1&I0&R2A   # force RTS/CTS after change
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null