|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Unspecified Transmit Phase B error (code20 )
Hi,
first off all, your session-trace does not match the posted config-file.
(the dialstring from trace has a @-sign appended, the ModemDialcmd not)
are you shure hylafax uses the correct file?
second if you have characters like \ in your commands, (like AT\Q3)
put the complete string in quotationmarks (like "AT\Q3")
the rest of the file is identical to our config with the same modem.
( we have the @-sign at the end of ModemDialCmd, works fine)
hope it helps
Christoph
Rolf Rocke schrieb:
>
> Hello,
> Problem: Cannot send a fax , receive fax is O.K.
> OS: SuseLinux 6.4
> Hylafax: Version 4.1 beta2
> Modem: Elsa Microlink 28,8 TQV
> Config.modem file original from Elsa
>
> After synchronistion with companion modem connection breaks down.
>
> Error.log:
>
> Nov 03 11:29:51.83: [ 1007]: SESSION BEGIN 00000039 492171xxxxxxx
> Nov 03 11:29:51.83: [ 1007]: SEND FAX: JOB 30 DEST xxxxxxx COMMID
> 00000039
> Nov 03 11:29:51.83: [ 1007]: MODEM set DTR OFF
> Nov 03 11:29:51.83: [ 1007]: DELAY 2600 ms
> Nov 03 11:29:54.43: [ 1007]: MODEM set DTR ON
> Nov 03 11:29:54.43: [ 1007]: MODEM set baud rate: 115200 baud, input
> flow RTS/CTS, output flow RTS/CTS
> Nov 03 11:29:54.43: [ 1007]: MODEM flush i/o
> Nov 03 11:29:54.43: [ 1007]: <-- [14:ATE0V1Q0S0=0H\r]
> Nov 03 11:29:54.44: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.44: [ 1007]: <-- [21:ATS8=2S7=60\Q3&D2&C1\r]
> Nov 03 11:29:54.45: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.45: [ 1007]: <-- [14:AT+FCLASS=2.0\r]
> Nov 03 11:29:54.46: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.46: [ 1007]: <-- [9:AT+FLO=2\r]
> Nov 03 11:29:54.47: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.47: [ 1007]: <-- [9:AT+FPP=0\r]
> Nov 03 11:29:54.48: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.48: [ 1007]: <-- [9:AT+FBO=0\r]
> Nov 03 11:29:54.49: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.49: [ 1007]: <-- [10:AT+FCT=30\r]
> Nov 03 11:29:54.50: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.50: [ 1007]: <-- [15:AT+FNR=1,1,1,1\r]
> Nov 03 11:29:54.51: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.51: [ 1007]: <-- [9:AT+FIE=0\r]
> Nov 03 11:29:54.52: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.52: [ 1007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Nov 03 11:29:54.53: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.53: [ 1007]: <-- [7:ATL1M1\r]
> Nov 03 11:29:54.54: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.54: [ 1007]: MODEM input buffering enabled
> Nov 03 11:29:54.54: [ 1007]: <-- [14:AT+FCLASS=2.0\r]
> Nov 03 11:29:54.65: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.65: [ 1007]: <-- [9:AT+FLO=2\r]
> Nov 03 11:29:54.76: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.76: [ 1007]: <-- [9:AT+FPP=0\r]
> Nov 03 11:29:54.87: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.87: [ 1007]: <-- [9:AT+FBO=0\r]
> Nov 03 11:29:54.98: [ 1007]: --> [2:OK]
> Nov 03 11:29:54.98: [ 1007]: <-- [10:AT+FCT=30\r]
> Nov 03 11:29:55.09: [ 1007]: --> [2:OK]
> Nov 03 11:29:55.09: [ 1007]: <-- [15:AT+FNR=1,1,1,1\r]
> Nov 03 11:29:55.20: [ 1007]: --> [2:OK]
> Nov 03 11:29:55.20: [ 1007]: <-- [9:AT+FIE=0\r]
> Nov 03 11:29:55.31: [ 1007]: --> [2:OK]
> Nov 03 11:29:55.31: [ 1007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Nov 03 11:29:55.42: [ 1007]: --> [2:OK]
> Nov 03 11:29:55.42: [ 1007]: <-- [29:AT+FLI="Rolf Rocke"\r]
> Nov 03 11:29:55.53: [ 1007]: --> [2:OK]
> Nov 03 11:29:55.53: [ 1007]: DIAL xxxxxxx
> Nov 03 11:29:55.53: [ 1007]: <-- [13:ATDTxxxxxxx@\r]
> Nov 03 11:30:10.83: [ 1007]: --> [4:+FCO]
> Nov 03 11:30:12.18: [ 1007]: --> [27:+FCI:" +49 2171 xxxxx"]
> Nov 03 11:30:12.18: [ 1007]: REMOTE CSI "+49 2171 xxxxx"
> Nov 03 11:30:12.18: [ 1007]: --> [20:+FIS:1,5,0,2,0,0,0,0]
> Nov 03 11:30:12.18: [ 1007]: --> [2:OK]
> Nov 03 11:30:12.18: [ 1007]: REMOTE best rate 14400 bit/s
> Nov 03 11:30:12.18: [ 1007]: REMOTE max page width 1728 pixels in 215 mm
>
> Nov 03 11:30:12.18: [ 1007]: REMOTE max unlimited page length
> Nov 03 11:30:12.18: [ 1007]: REMOTE best vres 7.7 line/mm
> Nov 03 11:30:12.18: [ 1007]: REMOTE best format 1-D MR
> Nov 03 11:30:12.18: [ 1007]: REMOTE best 0 ms/scanline
> Nov 03 11:30:12.18: [ 1007]: USE 14400 bit/s
> Nov 03 11:30:12.18: [ 1007]: USE 0 ms/scanline
> Nov 03 11:30:12.18: [ 1007]: <-- [4:ATH\r]
> Nov 03 11:30:13.79: [ 1007]: --> [7:+FHS:20]
> Nov 03 11:30:13.79: [ 1007]: REMOTE HANGUP: Unspecified Transmit Phase B
>
> error (code 20)
> Nov 03 11:30:14.95: [ 1007]: --> [2:OK]
> Nov 03 11:30:14.95: [ 1007]: MODEM set DTR OFF
> Nov 03 11:30:14.95: [ 1007]: SESSION END
>
> Config.modem:
>
> # Class 2.0 modem configuration for ELSA 33.6 TQV.
> #
> # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
> #
> CountryCode: 49
> AreaCode: 2171
> FAXNumber: +49.2171.xxxxxxx
> LongDistancePrefix: 0
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing: 527
> SessionTracing: 527
> RecvFileMode: 0644
> LogFileMode: 0600
> DeviceMode: 0666
> RingsBeforeAnswer: 1
> SpeakerVolume: LOW
> GettyArgs: "-r -b -s %s %l"
> LocalIdentifier: "Rolf Rocke"
> # LogFacility: local7
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "Von %%l|%c|Seite %%p von %%t"
> PercentGoodLines: 80
> MaxConsecutiveBadLines: 20
> MaxRecvPages: 25
> ModemPriority: 200
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class2.0 # use this to supply a hint
> ModemRate: 115200 # max rate for DCE-DTE
> communication
> ModemFlowControl: rtscts # XON/XOFF flow control assumed
> ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
>
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
> (or not)
> #
> # We normally append the "@" symbol to the dial string so that
> # the modem will wait 5 seconds before attempting to connect
> # and return result codes that distinguish between no carrier
> # and no answer. This makes it possible to avoid problems with
> # repeatedly dialing a number that doesn't have a fax machine
> # (kudos to Stuart Lynne for this trick.)
> #
> # NB: If you need to prefix phone numbers to get through a PBX,
> # put it in the ModemDialCmd; e.g. "DT9%s@".
> #
> ModemDialCmd: ATDT%s
> #
> # Other possible configuration stuff. The default strings are
> # shown below. Only those that are different from the defaults
> # need to be included in the configuration file.
> #
> #ModemResetCmds: ATX3 # stuff to do when modem
>
> is reset
> ModemAnswerCmd: ATA # use this to answer phone
> ModemNoFlowCmd: AT\Q0
> ModemHardFlowCmd: AT\Q3
> ModemSoftFlowCmd: AT\Q1
> ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
> ModemEchoOffCmd: ATE0 # disable command echo
> ModemVerboseResultsCmd: ATV1 # enable verbose command results
>
> ModemResultCodesCmd: ATQ0 # enable result codes
> ModemOnHookCmd: ATH # place phone on hook (hangup)
> ModemSoftResetCmd: ATZ # do soft reset of modem
> ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
> ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
> ModemRecvFillOrder: LSB2MSB # bit order of received
> facsimile
> ModemSendFillOrder: LSB2MSB # bit order modem expects for
> transmit
> #
> # Configuration parameters for Class 2.0 modems.
> #
> Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
> Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
> (direct)
> Class2CQCmd: "" # commands to enable copy
> quality proc.
> Class2AbortCmd: AT+FKS # abort session command
> Class2CQQueryCmd: AT+FCQ=? # query for copy quality
> capabilities
> Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
> Class2TBCCmd: AT+FPP=0 # setup stream mode
> Class2CRCmd: AT+FCR=1 # enable capability to receive
> Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
> Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
> Class2LIDCmd: AT+FLI # set local identifier command
> Class2DCCCmd: AT+FCC # set modem capabilities command
>
> Class2DISCmd: AT+FIS # set session parameters command
>
> Class2DDISCmd: "" # disable pre-dial DIS command
> hack
> Class2CIGCmd: AT+FPI # set polling identifier command
>
> Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
>
> Class2PIECmd: AT+FIE=0 # disable interrupt-enable
> command
> Class2PTSCmd: AT+FPS # set post-page status command
> Class2SPLCmd: AT+FSP # set polling indicator command
> Class2NFLOCmd: AT+FLO=0 # set no flow control command
> Class2SFLOCmd: AT+FLO=1 # set software flow control
> command
> Class2HFLOCmd: AT+FLO=2 # set hardware flow control
> command
>
> many thanks ins advance
> Rolf Rocke
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
> To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
