[hylafax-users] Unspecified Transmit Phase B error (code20 )

To: hylafax-users@hylafax.org
Subject: [hylafax-users] Unspecified Transmit Phase B error (code20 )
From: Rolf Rocke <rr@rocke.de>
Date: Mon, 06 Nov 2000 10:44:20 +0100

Hello,
Problem: Cannot send a fax , receive fax is O.K.
OS: SuseLinux 6.4
Hylafax: Version 4.1 beta2
Modem: Elsa Microlink 28,8 TQV
Config.modem file original from Elsa

After synchronistion with companion modem connection breaks down.

Error.log:

Nov 03 11:29:51.83: [ 1007]: SESSION BEGIN 00000039 492171xxxxxxx
Nov 03 11:29:51.83: [ 1007]: SEND FAX: JOB 30 DEST xxxxxxx COMMID
00000039
Nov 03 11:29:51.83: [ 1007]: MODEM set DTR OFF
Nov 03 11:29:51.83: [ 1007]: DELAY 2600 ms
Nov 03 11:29:54.43: [ 1007]: MODEM set DTR ON
Nov 03 11:29:54.43: [ 1007]: MODEM set baud rate: 115200 baud, input
flow RTS/CTS, output flow RTS/CTS
Nov 03 11:29:54.43: [ 1007]: MODEM flush i/o
Nov 03 11:29:54.43: [ 1007]: <-- [14:ATE0V1Q0S0=0H\r]
Nov 03 11:29:54.44: [ 1007]: --> [2:OK]
Nov 03 11:29:54.44: [ 1007]: <-- [21:ATS8=2S7=60\Q3&D2&C1\r]
Nov 03 11:29:54.45: [ 1007]: --> [2:OK]
Nov 03 11:29:54.45: [ 1007]: <-- [14:AT+FCLASS=2.0\r]
Nov 03 11:29:54.46: [ 1007]: --> [2:OK]
Nov 03 11:29:54.46: [ 1007]: <-- [9:AT+FLO=2\r]
Nov 03 11:29:54.47: [ 1007]: --> [2:OK]
Nov 03 11:29:54.47: [ 1007]: <-- [9:AT+FPP=0\r]
Nov 03 11:29:54.48: [ 1007]: --> [2:OK]
Nov 03 11:29:54.48: [ 1007]: <-- [9:AT+FBO=0\r]
Nov 03 11:29:54.49: [ 1007]: --> [2:OK]
Nov 03 11:29:54.49: [ 1007]: <-- [10:AT+FCT=30\r]
Nov 03 11:29:54.50: [ 1007]: --> [2:OK]
Nov 03 11:29:54.50: [ 1007]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 03 11:29:54.51: [ 1007]: --> [2:OK]
Nov 03 11:29:54.51: [ 1007]: <-- [9:AT+FIE=0\r]
Nov 03 11:29:54.52: [ 1007]: --> [2:OK]
Nov 03 11:29:54.52: [ 1007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 03 11:29:54.53: [ 1007]: --> [2:OK]
Nov 03 11:29:54.53: [ 1007]: <-- [7:ATL1M1\r]
Nov 03 11:29:54.54: [ 1007]: --> [2:OK]
Nov 03 11:29:54.54: [ 1007]: MODEM input buffering enabled
Nov 03 11:29:54.54: [ 1007]: <-- [14:AT+FCLASS=2.0\r]
Nov 03 11:29:54.65: [ 1007]: --> [2:OK]
Nov 03 11:29:54.65: [ 1007]: <-- [9:AT+FLO=2\r]
Nov 03 11:29:54.76: [ 1007]: --> [2:OK]
Nov 03 11:29:54.76: [ 1007]: <-- [9:AT+FPP=0\r]
Nov 03 11:29:54.87: [ 1007]: --> [2:OK]
Nov 03 11:29:54.87: [ 1007]: <-- [9:AT+FBO=0\r]
Nov 03 11:29:54.98: [ 1007]: --> [2:OK]
Nov 03 11:29:54.98: [ 1007]: <-- [10:AT+FCT=30\r]
Nov 03 11:29:55.09: [ 1007]: --> [2:OK]
Nov 03 11:29:55.09: [ 1007]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 03 11:29:55.20: [ 1007]: --> [2:OK]
Nov 03 11:29:55.20: [ 1007]: <-- [9:AT+FIE=0\r]
Nov 03 11:29:55.31: [ 1007]: --> [2:OK]
Nov 03 11:29:55.31: [ 1007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 03 11:29:55.42: [ 1007]: --> [2:OK]
Nov 03 11:29:55.42: [ 1007]: <-- [29:AT+FLI="Rolf Rocke"\r]
Nov 03 11:29:55.53: [ 1007]: --> [2:OK]
Nov 03 11:29:55.53: [ 1007]: DIAL xxxxxxx
Nov 03 11:29:55.53: [ 1007]: <-- [13:ATDTxxxxxxx@\r]
Nov 03 11:30:10.83: [ 1007]: --> [4:+FCO]
Nov 03 11:30:12.18: [ 1007]: --> [27:+FCI:"      +49 2171 xxxxx"]
Nov 03 11:30:12.18: [ 1007]: REMOTE CSI "+49 2171 xxxxx"
Nov 03 11:30:12.18: [ 1007]: --> [20:+FIS:1,5,0,2,0,0,0,0]
Nov 03 11:30:12.18: [ 1007]: --> [2:OK]
Nov 03 11:30:12.18: [ 1007]: REMOTE best rate 14400 bit/s
Nov 03 11:30:12.18: [ 1007]: REMOTE max page width 1728 pixels in 215 mm

Nov 03 11:30:12.18: [ 1007]: REMOTE max unlimited page length
Nov 03 11:30:12.18: [ 1007]: REMOTE best vres 7.7 line/mm
Nov 03 11:30:12.18: [ 1007]: REMOTE best format 1-D MR
Nov 03 11:30:12.18: [ 1007]: REMOTE best 0 ms/scanline
Nov 03 11:30:12.18: [ 1007]: USE 14400 bit/s
Nov 03 11:30:12.18: [ 1007]: USE 0 ms/scanline
Nov 03 11:30:12.18: [ 1007]: <-- [4:ATH\r]
Nov 03 11:30:13.79: [ 1007]: --> [7:+FHS:20]
Nov 03 11:30:13.79: [ 1007]: REMOTE HANGUP: Unspecified Transmit Phase B

error (code 20)
Nov 03 11:30:14.95: [ 1007]: --> [2:OK]
Nov 03 11:30:14.95: [ 1007]: MODEM set DTR OFF
Nov 03 11:30:14.95: [ 1007]: SESSION END


Config.modem:

# Class 2.0 modem configuration for ELSA 33.6 TQV.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            49
AreaCode:               2171
FAXNumber:              +49.2171.xxxxxxx
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          527
SessionTracing:         527
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          LOW
GettyArgs:              "-r -b -s %s %l"
LocalIdentifier:        "Rolf Rocke"
# LogFacility:            local7
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "Von %%l|%c|Seite %%p von %%t"
PercentGoodLines:       80
MaxConsecutiveBadLines: 20
MaxRecvPages:           25
ModemPriority:          200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              115200          # max rate for DCE-DTE
communication
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem

ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDT%s
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:                ATX3            # stuff to do when modem

is reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT\Q0
ModemHardFlowCmd:       AT\Q3
ModemSoftFlowCmd:       AT\Q1
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results

ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received
facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D
(direct)
Class2CQCmd:            ""              # commands to enable copy
quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command

Class2DISCmd:           AT+FIS          # set session parameters command

Class2DDISCmd:          ""              # disable pre-dial DIS command
hack
Class2CIGCmd:           AT+FPI          # set polling identifier command

Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command

Class2PIECmd:           AT+FIE=0        # disable interrupt-enable
command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control
command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control
command

many thanks ins advance
Rolf Rocke





____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null

Follow-Ups:
- Re: [hylafax-users] Unspecified Transmit Phase B error (code20 )
  - From: Christoph Scheeder <christoph.scheeder@scheeder.de>

Prev by Date: [hylafax-users] choose client program
Next by Date: [hylafax-users] how to force to queued faxes ...
Prev by thread: Re: [hylafax-users] choose client program
Next by thread: Re: [hylafax-users] Unspecified Transmit Phase B error (code20 )
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services