|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] newbie questions
maybe try taking out the @ in the dialing rules
--Jim
> -----Original Message-----
> From: Eric Wood [mailto:eric@interplas.com]
> Sent: Wednesday, November 01, 2000 3:10 PM
> To: hylafax-users@hylafax.org
> Subject: [hylafax-users] newbie questions
>
>
> Hello,
> I'm struggling over a couple of things:
>
> 1. I sent a test fax using "sendfax -n -d 2977186
> /etc/passwd/" and I'm
> using a generic class 2.0 config file, generic modem, RH 7.0:
>
> After the dial command, I get funky FNF and DNF characters
> from the remote
> fax machine. Is this normal?
> Also, the first few lines of the /etc/passwd file come out
> okay but the
> remainer of the page is "squished" and unreadable. Is it possible
> that the the graphics conversion utilities are not
> compatiable for Hylafax
> and RH 7.0?
>
> Thanks,
> -eric wood
>
>
> Mar 08 12:44:47.12: [ 8445]: SESSION BEGIN 00000010 18642977186
> Mar 08 12:44:47.13: [ 8445]: SEND FAX: JOB 9 DEST 2977186
> COMMID 00000010
> Mar 08 12:44:47.13: [ 8445]: DELAY 2600 ms
> Mar 08 12:44:49.72: [ 8445]: <-- [4:ATZ\r]
> Mar 08 12:44:49.86: [ 8445]: --> [2:OK]
> Mar 08 12:44:49.86: [ 8445]: <-- [15:ATE0V1Q0S0=0H0\r]
> Mar 08 12:44:50.00: [ 8445]: --> [14:ATE0V1Q0S0=0H0]
> Mar 08 12:44:50.00: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.00: [ 8445]: <-- [12:ATS8=2S7=60\r]
> Mar 08 12:44:50.14: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.14: [ 8445]: <-- [14:AT+FCLASS=2.0\r]
> Mar 08 12:44:50.28: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.28: [ 8445]: <-- [9:AT+FLO=0\r]
> Mar 08 12:44:50.42: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.42: [ 8445]: <-- [9:AT+FPP=0\r]
> Mar 08 12:44:50.56: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.56: [ 8445]: <-- [9:AT+FBO=0\r]
> Mar 08 12:44:50.70: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.70: [ 8445]: <-- [10:AT+FCT=30\r]
> Mar 08 12:44:50.84: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.84: [ 8445]: <-- [15:AT+FNR=1,1,1,1\r]
> Mar 08 12:44:50.98: [ 8445]: --> [2:OK]
> Mar 08 12:44:50.98: [ 8445]: <-- [9:AT+FIE=0\r]
> Mar 08 12:44:51.12: [ 8445]: --> [2:OK]
> Mar 08 12:44:51.12: [ 8445]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]Mar 08
> 12:44:51.26: [ 8445]: --> [2:OK]
> Mar 08 12:44:51.26: [ 8445]: <-- [5:ATM0\r]
> Mar 08 12:44:51.39: [ 8445]: --> [2:OK]
> Mar 08 12:44:51.39: [ 8445]: <-- [14:AT+FCLASS=2.0\r]
> Mar 08 12:44:51.63: [ 8445]: --> [2:OK]
> Mar 08 12:44:51.63: [ 8445]: <-- [9:AT+FLO=0\r]
> Mar 08 12:44:51.87: [ 8445]: --> [2:OK]
> Mar 08 12:44:51.87: [ 8445]: <-- [9:AT+FPP=0\r]
> Mar 08 12:44:52.11: [ 8445]: --> [2:OK]
> Mar 08 12:44:52.11: [ 8445]: <-- [9:AT+FBO=0\r]
> Mar 08 12:44:52.35: [ 8445]: --> [2:OK]
> Mar 08 12:44:52.35: [ 8445]: <-- [10:AT+FCT=30\r]
> Mar 08 12:44:52.59: [ 8445]: --> [2:OK]
> Mar 08 12:44:52.59: [ 8445]: <-- [15:AT+FNR=1,1,1,1\r]
> Mar 08 12:44:52.83: [ 8445]: --> [2:OK]
> Mar 08 12:44:52.83: [ 8445]: <-- [9:AT+FIE=0\r]
> Mar 08 12:44:53.07: [ 8445]: --> [2:OK]
> Mar 08 12:44:53.07: [ 8445]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Mar 08 12:44:53.31: [ 8445]: --> [2:OK]
> Mar 08 12:44:53.31: [ 8445]: <-- [19:AT+FLI="InterPlas"\r]
> Mar 08 12:44:53.55: [ 8445]: --> [2:OK]
> Mar 08 12:44:53.55: [ 8445]: DIAL 2977186
> Mar 08 12:44:53.55: [ 8445]: <-- [14:ATDT92977186@\r]
> Mar 08 12:45:09.09: [ 8445]: --> [4:+FCO]
> Mar 08 12:45:10.94: [ 8445]: --> [15:+FNF:%ÿþ<92>^PM^BX*,]
> Mar 08 12:45:10.94: [ 8445]: REMOTE NSF "%ÿþ<92>^PM^BX*,"
> Mar 08 12:45:10.94: [ 8445]: NSF remote fax equipment: unknown
> Mar 08 12:45:10.94: [ 8445]: --> [20:+FIS:1,5,2,2,1,0,0,2]
> Mar 08 12:45:10.94: [ 8445]: --> [2:OK]
> Mar 08 12:45:10.94: [ 8445]: REMOTE best rate 14400 bit/s
> Mar 08 12:45:10.94: [ 8445]: REMOTE max page width 2432
> pixels in 303 mm
> Mar 08 12:45:10.94: [ 8445]: REMOTE max unlimited page length
> Mar 08 12:45:10.94: [ 8445]: REMOTE best vres 7.7 line/mm
> Mar 08 12:45:10.94: [ 8445]: REMOTE best format 2-D MR
> Mar 08 12:45:10.94: [ 8445]: REMOTE best 10 ms, 5 ms/scanline
> Mar 08 12:45:10.94: [ 8445]: USE 14400 bit/s
> Mar 08 12:45:10.94: [ 8445]: USE 10 ms, 5 ms/scanline
> Mar 08 12:45:10.94: [ 8445]: SEND file "docq/doc9.ps;31"
> Mar 08 12:45:10.94: [ 8445]: USE page width 1728 pixels in 215 mm
> Mar 08 12:45:10.94: [ 8445]: USE unlimited page length
> Mar 08 12:45:10.94: [ 8445]: USE 7.7 line/mm
> Mar 08 12:45:10.94: [ 8445]: USE 1-D MR
> Mar 08 12:45:10.94: [ 8445]: <-- [23:AT+FIS=1,5,0,2,0,0,0,2\r]
> Mar 08 12:45:11.18: [ 8445]: --> [2:OK]
> Mar 08 12:45:11.18: [ 8445]: <-- [7:AT+FDT\r]
> Mar 08 12:45:11.46: [ 8445]: --> [20:+FCS:1,5,0,2,0,0,0,2]
> Mar 08 12:45:18.31: [ 8445]: --> [7:CONNECT]
> Mar 08 12:45:18.31: [ 8445]: SEND begin page
> Mar 08 12:45:18.31: [ 8445]: <-- data [1030]
> <more data lines are cut for brevity>
> Mar 08 12:45:38.31: [ 8445]: <-- data [738]
> Mar 08 12:45:40.31: [ 8445]: SENT 42721 bytes of data
> Mar 08 12:45:40.31: [ 8445]: SEND 1D RTC
> Mar 08 12:45:40.31: [ 8445]: <-- data [9]
> Mar 08 12:45:40.31: [ 8445]: SEND end page
> Mar 08 12:45:40.31: [ 8445]: SEND send EOP (no more pages or
> documents)
> Mar 08 12:45:40.31: [ 8445]: <-- data [2]
> Mar 08 12:45:46.88: [ 8445]: --> [7:+FHS:00]
> Mar 08 12:45:46.88: [ 8445]: REMOTE HANGUP: Normal and proper end of
> connection (code 0)
> Mar 08 12:45:46.88: [ 8445]: SEND recv MCF (message confirmation)
> Mar 08 12:45:46.88: [ 8445]: SEND FAX (00000010): FROM
> root@secure.intgrp.com TO
> 2977186 (page 1 of 1 sent in 0:36)
> Mar 08 12:45:46.88: [ 8445]: SEND FAX (00000010): FROM
> root@secure.intgrp.com TO
> 2977186 (docq/doc9.ps;31 sent in 0:36)
> Mar 08 12:45:46.88: [ 8445]: <-- [5:ATH0\r]
> Mar 08 12:45:47.00: [ 8445]: --> [2:OK]
> Mar 08 12:45:47.00: [ 8445]: SESSION END
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> To unsub: mail -s unsubscribe
> hylafax-users-request@hylafax.org < /dev/null
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
