[hylafax-users] FW: facsimile received from

["Budi Gautama" <budig@apakabar.com>]

Hi,

I have problem in receiving fax from certain fax machines, error message as
follows.

Pls help.

Budi

-----Original Message-----
From: The HylaFAX Receive Agent [mailto:fax@hirawan.centrin.net.id]
Sent: Thursday, September 14, 2000 10:45 AM
To: hirawan@bdg.centrin.net.id
Subject: facsimile received from


recvq/fax00025.tif (ftp://hirawan.centrin.net.id:4559/recvq/fax00025.tif):
    Sender:
     Pages: 2
   Quality: Fine
      Page: 1728 by 144
  Received: 2000:09:14 05:43:05
TimeToRecv: 5:01:39
SignalRate: 14400 bit/s
DataFormat: 1-D MR
ReceivedOn: ttyS0

The full document was not received because:

    Unspecified Phase C error, including too much delay between TCF and +FDR
command

    ---- Transcript of session follows ----

Sep 14 05:42:50.44: [ 7250]: SESSION BEGIN 00000041 62224250025
Sep 14 05:42:50.44: [ 7250]: <-- [4:ATA\r]
Sep 14 05:42:52.94: [ 7250]: --> [3:FAX]
Sep 14 05:42:58.64: [ 7250]: --> [5:+FCON]
Sep 14 05:42:58.64: [ 7250]: ANSWER: FAX CONNECTION
Sep 14 05:42:58.64: [ 7250]: RECV FAX: begin
Sep 14 05:42:59.87: [ 7250]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
Sep 14 05:42:59.87: [ 7250]: REMOTE wants 14400 bit/s
Sep 14 05:42:59.87: [ 7250]: REMOTE wants page width 1728 pixels in 215 mm
Sep 14 05:42:59.87: [ 7250]: REMOTE wants unlimited page length
Sep 14 05:42:59.87: [ 7250]: REMOTE wants 7.7 line/mm
Sep 14 05:42:59.87: [ 7250]: REMOTE wants 1-D MR
Sep 14 05:42:59.98: [ 7250]: --> [2:OK]
Sep 14 05:42:59.98: [ 7250]: <-- [7:AT+FDR\r]
Sep 14 05:43:03.05: [ 7250]: --> [5:+FCFR]
Sep 14 05:43:05.05: [ 7250]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
Sep 14 05:43:05.05: [ 7250]: REMOTE wants 14400 bit/s
Sep 14 05:43:05.05: [ 7250]: REMOTE wants page width 1728 pixels in 215 mm
Sep 14 05:43:05.05: [ 7250]: REMOTE wants unlimited page length
Sep 14 05:43:05.05: [ 7250]: REMOTE wants 7.7 line/mm
Sep 14 05:43:05.05: [ 7250]: REMOTE wants 1-D MR
Sep 14 05:43:05.05: [ 7250]: --> [7:CONNECT]
Sep 14 05:43:05.05: [ 7250]: RECV: begin page
Sep 14 05:43:05.05: [ 7250]: RECV: send trigger 022
Sep 14 05:43:10.24: [ 7250]: RECV: 1116 total lines, 0 bad lines, 0
consecutive bad lines
Sep 14 05:43:10.24: [ 7250]: --> [17:+FPTS: 1,2219,0,0]
Sep 14 05:43:11.71: [ 7250]: --> [7:+FET: 0]
Sep 14 05:43:11.71: [ 7250]: RECV recv MPS (more pages, same document)
Sep 14 05:43:11.71: [ 7250]: --> [2:OK]
Sep 14 05:43:11.71: [ 7250]: RECV send MCF (message confirmation)
Sep 14 05:43:11.72: [ 7250]: RECV FAX (00000041): from <UNSPECIFIED>, page 1
in 0:12, INF, 7.7 line/mm, 1-D MR
Sep 14 05:43:11.72: [ 7250]: <-- [7:AT+FDR\r]
Sep 14 05:43:13.62: [ 7250]: --> [7:CONNECT]
Sep 14 05:43:13.62: [ 7250]: RECV: begin page
Sep 14 05:43:13.62: [ 7250]: RECV: send trigger 022
Sep 14 10:44:39.93: [ 7250]: RECV: 25089 total lines, 24117 bad lines, 858
consecutive bad lines
Sep 14 10:44:39.93: [ 7250]: --> [17:+FPTS: 2,2219,0,0]
Sep 14 10:45:09.93: [ 7250]: MODEM <Timeout>
Sep 14 10:45:09.93: [ 7250]: REMOTE HANGUP: Unspecified Phase C error,
including too much delay between TCF and +FDR command (code 90)
Sep 14 10:45:09.93: [ 7250]: RECV FAX (00000041): recvq/fax00025.tif from
<UNSPECIFIED>, route to <unspecified>, 1 pages in 5:02:11
Sep 14 10:45:09.93: [ 7250]: RECV FAX: Unspecified Phase C error, including
too much delay between TCF and +FDR command
Sep 14 10:45:09.93: [ 7250]: <-- [6:AT+FK\r]
Sep 14 10:45:21.53: [ 7250]: --> [10:+FHNG: 101]
Sep 14 10:45:21.53: [ 7250]: REMOTE HANGUP: RSPREC invalid response received
(code 101)
Sep 14 10:45:23.36: [ 7250]: --> [2:OK]
Sep 14 10:45:23.36: [ 7250]: RECV FAX (00000041): session with <UNSPECIFIED>
terminated abnormally: Unspecified Phase C error, including too much delay
between TCF and +FDR command
Sep 14 10:45:23.36: [ 7250]: RECV FAX: bin/faxrcvd "recvq/fax00025.tif"
"ttyS0" "00000041" "Unspecified Phase C error, including too much delay
between TCF and +FDR command"



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null