Re: [hylafax-users] Need config.ttyS1 for USR faxmodems

["Keith G. Murphy" <keithmur@mindspring.com>]

Luigi Tura wrote:
> 
> I'm trying to configure a hylafax-4.1beta2-5rh6 in a linux Red Hat 6.2.
> I tested it with a 3Com U.S Robotics 56K Message Modem and it seems to work
> ok with a standard 2.0 config.ttyS1 file.
> I also tried with a 3Com U.S Robotics 56K Faxmodem and it doesn't work at all.
> Did anybody test these modems?
> I'd like to have advices to correct the config.ttyS1 files?
> Is there a place in Internet where I can find more info about how to
> configure HylaFAX with USR faxmodems?

I'm attaching mine.  Hope it helps.
# $Header: /usr/people/sam/fax/./config/RCS/usr-2.0,v 1.3 1995/04/08 21:25:03 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1995 Sam Leffler
# Copyright (c) 1991-1995 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:		1
AreaCode:		901
FAXNumber:		+1.901.767.5578
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0666
LogFileMode:		0666
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
#GettyArgs:		"dial.115200 -"
GettyArgs:  "-r -b -s %s %l"
LocalIdentifier:	CRI
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
#
# KGM 03/24/2000  Attempt to reset more fully: seems helpful with USR's
#
ModemResetCmds:         AT&F1   #Factory template for RTS/CTS flow control
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we disable it to keep the
# fax software from complaining.
#
Class2CQCmd:            AT+FCQ=0,0      # disable copy quality checking
Class2CQQueryCmd:       !(0),(0)        # override modem response
#
Class2NRCmd:            AT+FNR=1,1,1,0  # setup status reporting command