[hylafax-users] Re: Not even Tiff/F format gets sent ok (nokia & usr)

[Dmitry Bely <dbely@mail.ru>]

Borut Kurnik <borut.kurnik@add.si> writes:

...

> # $Id: class1,v 1.2 1999/01/10 09:09:37 robert Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> # 
> # Permission to use, copy, modify, distribute, and sell this software and 
> # its documentation for any purpose is hereby granted without fee, provided
> # that (i) the above copyright notices and this permission notice appear in
> # all copies of the software and related documentation, and (ii) the names of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> # 
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
> # 
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
> # OF THIS SOFTWARE.
> #
> 
> #
> # Generic Class 1 modem configuration.
> #
> # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
> #
> CountryCode:		1
> AreaCode:		01
> FAXNumber:		1790062
> LongDistancePrefix:	00
> InternationalPrefix:	00
> DialStringRules:	etc/dialrules
> ServerTracing:		1
> SessionTracing:		11
> RecvFileMode:		0644
> LogFileMode:		0644
> DeviceMode:		0644
> RingsBeforeAnswer:	1
> SpeakerVolume:		off
> GettyArgs:		"-h %l dx_%s"
> LocalIdentifier:	"ADD d.o.o."
> TagLineFont:		etc/lutRS18.pcf
> TagLineFormat:		"From %%l|%c|Page %%p of %%t"
> MaxRecvPages:		25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:		Class1		# use this to supply a hint
> #ModemRate:		19200		# rate for DCE-DTE communication
> ModemFlowControl:	RTSCTS 		# XON/XOFF flow control assumed
> #
> #ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
> #ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
> #GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
> #
> # We normally append the "@" symbol to the dial string so that
> # the modem will wait 5 seconds before attempting to connect
> # and return result codes that distinguish between no carrier
> # and no answer.  This makes it possible to avoid problems with
> # repeatedly dialing a number that doesn't have a fax machine
> # (kudos to Stuart Lynne for this trick.)
> #
> # NB: If you need to prefix phone numbers to get through a PBX,
> #     put it in the ModemDialCmd; e.g. "DT9%s@".
> #
> #ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
> #
> # Other possible configuration stuff.  The default strings are
> # shown below.  Only those that are different from the defaults
> # need to be included in the configuration file.
> #
> #ModemResetCmds:		""		# stuff to do when modem is reset

Add

ModemResetCmds:		ATZ

> #ModemAnswerCmd:		ATA		# use this to answer phone
> #ModemNoFlowCmd:		AT&K		# disable flow control cmd
> ModemHardFlowCmd:	AT&H1		# hardware flow control cmd
> ModemSoftFlowCmd:	AT&H2		# software flow control cmd

I repeat once again: copy ModemNoFlowCmd, ModemHardFlowCmd,
ModemSoftFlowCmd from config/usr-rts (better the whole modem-related part)!
Your modem is not generic!

...

> Class1Cmd:		AT+FCLASS=1	# command to enter class 1
> Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & response
> Class1SendPPMDelay:	75		# 75ms delay before sending PPM
> Class1SendTCFDelay:	75		# 75ms delay between sending DCS & TCF
> Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
> Class1RecvAbortOK:	200		# wait 200ms for abort response
> Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
> Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
> Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
> Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration

useless stuff. Just comment it out.

> Class1HFLOCmd:   AT&H1
> Class1SFLOCmd:   AT&H2
> Class1NFLOCmd:   AT&H0

also copy from config/usr-rts

> # $Id: class2.0,v 1.2 1999/01/10 09:09:37 robert Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> # 
> # Permission to use, copy, modify, distribute, and sell this software and 
> # its documentation for any purpose is hereby granted without fee, provided
> # that (i) the above copyright notices and this permission notice appear in
> # all copies of the software and related documentation, and (ii) the names of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> # 
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
> # 
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
> # OF THIS SOFTWARE.
> #
> 
> #
> # Generic Class 2.0 modem configuration.

Class 2.0 won't relialably work with USRs. Just forget about it :-)

Hope to hear from you soon,
Dmitry




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null