[hylafax-users] Re: Not even Tiff/F format gets sent ok, log file looks ok

[Dmitry Bely <dbely@mail.ru>]

Borut Kurnik <borut.kurnik@ADD.SI> writes:

> Even if I have pure Tiff/F format already or the fax server creates it in the
> process, when i give it a text file, the result is the same (i only get upper
> halfs of the letters in first line of text, as i mentioned).
> 
> >From the WHFC client I even get nothing, although the document gets to the
> server side converted from eig.: MS WORD to postscript correctly.
> 
> I checked all the documents after the conversion in the  './docq' directory.
> Everything looks just fine.
> 
> I tried hw and sw flow control and results are the same.

How did you changed the flow control? What hardware are you using? That
about the log with SessionTracing=0x7FF?

> Thanks
> 
> Borut
> 
> Jun 08 08:55:18.89: [17066]: SESSION BEGIN 00000059 10137
> Jun 08 08:55:18.89: [17066]: SEND FAX: JOB 98 DEST 37 COMMID 00000059
> Jun 08 08:55:18.89: [17066]: DELAY 2600 ms
> Jun 08 08:55:21.49: [17066]: <-- [15:ATE0V1Q0S0=0H0\r]
> Jun 08 08:55:21.63: [17066]: --> [2:OK]
> Jun 08 08:55:21.63: [17066]: <-- [12:ATS8=2S7=60\r]
> Jun 08 08:55:21.77: [17066]: --> [2:OK]
> Jun 08 08:55:21.77: [17066]: <-- [12:AT+FCLASS=1\r]
> Jun 08 08:55:21.91: [17066]: --> [2:OK]
> Jun 08 08:55:21.91: [17066]: <-- [5:ATM0\r]
> Jun 08 08:55:22.05: [17066]: --> [2:OK]
> Jun 08 08:55:22.05: [17066]: <-- [12:AT+FCLASS=1\r]
> Jun 08 08:55:22.29: [17066]: --> [2:OK]

Flow control is not explicitly set. So log does not look OK.

> Jun 08 08:55:22.29: [17066]: DIAL 37
> Jun 08 08:55:22.29: [17066]: <-- [7:ATDT37\r]
> Jun 08 08:55:38.14: [17066]: --> [7:CONNECT]
> Jun 08 08:55:39.89: [17066]: --> [2:OK]
> Jun 08 08:55:39.89: [17066]: <-- [9:AT+FRH=3\r]
> Jun 08 08:55:39.91: [17066]: --> [7:CONNECT]
> Jun 08 08:55:40.59: [17066]: --> [2:OK]
> Jun 08 08:55:40.59: [17066]: REMOTE CSI "+386 61 1790037"
> Jun 08 08:55:40.59: [17066]: <-- [9:AT+FRH=3\r]
> Jun 08 08:55:40.61: [17066]: --> [7:CONNECT]
> Jun 08 08:55:40.88: [17066]: --> [2:OK]
> Jun 08 08:55:40.88: [17066]: REMOTE best rate 14400 bit/s
> Jun 08 08:55:40.88: [17066]: REMOTE max page width 1728 pixels in 215 mm
> Jun 08 08:55:40.88: [17066]: REMOTE max unlimited page length 
> Jun 08 08:55:40.88: [17066]: REMOTE best vres 7.7 line/mm
> Jun 08 08:55:40.88: [17066]: REMOTE best format 2-D MMR
> Jun 08 08:55:40.88: [17066]: REMOTE supports T.30 Annex A, ECM
> Jun 08 08:55:40.88: [17066]: REMOTE best 10 ms/scanline
> Jun 08 08:55:40.88: [17066]: USE 14400 bit/s
> Jun 08 08:55:40.88: [17066]: USE 10 ms/scanline
> Jun 08 08:55:40.88: [17066]: SEND file "docq/doc100.ps;00"
> Jun 08 08:55:40.88: [17066]: USE page width 1728 pixels in 215 mm
> Jun 08 08:55:40.88: [17066]: USE unlimited page length 
> Jun 08 08:55:40.88: [17066]: USE 3.85 line/mm
> Jun 08 08:55:40.88: [17066]: USE 1-D MR
> Jun 08 08:55:40.88: [17066]: SEND training at v.17 14400 bit/s
> Jun 08 08:55:40.88: [17066]: <-- [9:AT+FTH=3\r]
> Jun 08 08:55:41.08: [17066]: --> [7:CONNECT]
> Jun 08 08:55:41.08: [17066]: <-- data [23]
> Jun 08 08:55:41.08: [17066]: <-- data [2]
> Jun 08 08:55:41.11: [17066]: --> [7:CONNECT]
> Jun 08 08:55:41.11: [17066]: <-- data [6]
> Jun 08 08:55:41.11: [17066]: <-- data [2]
> Jun 08 08:55:43.06: [17066]: --> [2:OK]
> Jun 08 08:55:43.06: [17066]: DELAY 75 ms
> Jun 08 08:55:43.14: [17066]: <-- [11:AT+FTM=145\r]
> Jun 08 08:55:44.62: [17066]: --> [7:CONNECT]
> Jun 08 08:55:44.62: [17066]: <-- data [1024]
> Jun 08 08:55:44.62: [17066]: <-- data [1024]
> Jun 08 08:55:44.62: [17066]: <-- data [652]
> Jun 08 08:55:44.62: [17066]: <-- data [2]
> Jun 08 08:55:46.15: [17066]: --> [2:OK]
> Jun 08 08:55:46.15: [17066]: <-- [9:AT+FRH=3\r]
> Jun 08 08:55:46.40: [17066]: --> [7:CONNECT]
> Jun 08 08:55:47.42: [17066]: --> [2:OK]
> Jun 08 08:55:47.42: [17066]: TRAINING succeeded
> Jun 08 08:55:47.42: [17066]: <-- [11:AT+FTM=146\r]
> Jun 08 08:55:47.68: [17066]: --> [7:CONNECT]
> Jun 08 08:55:47.68: [17066]: SEND begin page
> Jun 08 08:55:47.68: [17066]: <-- data [1028]
> Jun 08 08:55:47.68: [17066]: <-- data [1024]
> Jun 08 08:55:47.68: [17066]: <-- data [216]
> Jun 08 08:55:47.68: [17066]: SENT 2264 bytes of data
> Jun 08 08:55:47.68: [17066]: SEND 1D RTC
> Jun 08 08:55:47.68: [17066]: <-- data [29]
> Jun 08 08:55:47.68: [17066]: <-- data [2]
> Jun 08 08:55:47.68: [17066]: SEND end page
> Jun 08 08:55:48.98: [17066]: --> [2:OK]
> Jun 08 08:55:48.98: [17066]: DELAY 95 ms
> Jun 08 08:55:49.08: [17066]: SEND send EOP (no more pages or documents)
> Jun 08 08:55:49.08: [17066]: <-- [9:AT+FTH=3\r]
> Jun 08 08:55:49.24: [17066]: --> [7:CONNECT]
> Jun 08 08:55:49.24: [17066]: <-- data [3]
> Jun 08 08:55:49.24: [17066]: <-- data [2]
> Jun 08 08:55:50.42: [17066]: --> [2:OK]
> Jun 08 08:55:50.42: [17066]: <-- [9:AT+FRH=3\r]
> Jun 08 08:55:50.84: [17066]: --> [7:CONNECT]
> Jun 08 08:55:51.67: [17066]: --> [2:OK]
> Jun 08 08:55:51.67: [17066]: SEND recv MCF (message confirmation)
> Jun 08 08:55:51.67: [17066]: SEND FAX (00000059): FROM borut.kurnik@add.si TO 37 (page 1 of 1 sent in 0:11)
> Jun 08 08:55:51.67: [17066]: SEND FAX (00000059): FROM borut.kurnik@add.si TO 37 (docq/doc100.ps;00 sent in 0:11)
> Jun 08 08:55:51.67: [17066]: <-- [9:AT+FTH=3\r]
> Jun 08 08:55:51.87: [17066]: --> [7:CONNECT]
> Jun 08 08:55:51.87: [17066]: <-- data [3]
> Jun 08 08:55:51.87: [17066]: <-- data [2]
> Jun 08 08:55:53.05: [17066]: --> [2:OK]
> Jun 08 08:55:53.05: [17066]: <-- [5:ATH0\r]
> Jun 08 08:55:53.29: [17066]: --> [2:OK]
> Jun 08 08:55:53.29: [17066]: SESSION END

Hope to hear from you soon,
Dmitry




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null