|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
GVC Modem and Phase B unspecified error
Hi all,
since a couple days I am trying to get HylaFax working on Intel hardware
running SuSe 6.4 Linux distribution. HylaFax came precompiled within
this distribution.
The modem in use identifies itself as "GVC Rockwell 144DPI/KA1131-00"
During HylaFax setup a modem configuration file 'gvc-288-2' was used.
When using sendfax to send a postscript file to any of three fax receivers
(standard fax machines, no fax modems on computers) I get an "Unspecified
phase B error (code 20)" I did try to include the Class2DDISCmd string "AT+FDIS"
to my config file but it still won't work. Below is the session log. Each session stops
at the same point during connection negotiations. Might be someone can help.
Thanks much for your time and effort
Frank Schnell
========================== Session log ===================================
May 25 10:16:57.51: [ 2488]: SESSION BEGIN 00000007 3227078777May 25 10:16:57.51: [ 2488]: SEND FAX: JOB 13 DEST 7078777 COMMID 00000007May 25 10:16:57.51: [ 2488]: DELAY 2600 msMay 25 10:17:00.11: [ 2488]: <-- [15:ATE0V1Q0S0=0H0\r]May 25 10:17:00.86: [ 2488]: --> [14:ATE0V1Q0S0=0H0]May 25 10:17:00.86: [ 2488]: --> [2:OK]May 25 10:17:00.86: [ 2488]: <-- [21:ATS8=2S7=60\Q3&D3&C1\r]May 25 10:17:00.98: [ 2488]: --> [2:OK]May 25 10:17:00.98: [ 2488]: <-- [12:AT+FCLASS=2\r]May 25 10:17:01.09: [ 2488]: --> [2:OK]May 25 10:17:01.09: [ 2488]: <-- [3:AT\r]May 25 10:17:01.10: [ 2488]: --> [2:OK]May 25 10:17:01.10: [ 2488]: <-- [10:AT+FBOR=0\r]May 25 10:17:01.11: [ 2488]: --> [2:OK]May 25 10:17:01.11: [ 2488]: <-- [3:AT\r]May 25 10:17:01.12: [ 2488]: --> [2:OK]May 25 10:17:01.12: [ 2488]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]May 25 10:17:01.14: [ 2488]: --> [2:OK]May 25 10:17:01.14: [ 2488]: <-- [5:ATM0\r]May 25 10:17:01.15: [ 2488]: --> [2:OK]May 25 10:17:01.15: [ 2488]: <-- [12:AT+FCLASS=2\r]May 25 10:17:01.26: [ 2488]: --> [2:OK]May 25 10:17:01.26: [ 2488]: <-- [3:AT\r]May 25 10:17:01.37: [ 2488]: --> [2:OK]May 25 10:17:01.37: [ 2488]: <-- [10:AT+FBOR=0\r]May 25 10:17:01.48: [ 2488]: --> [2:OK]May 25 10:17:01.48: [ 2488]: <-- [3:AT\r]May 25 10:17:01.59: [ 2488]: --> [2:OK]May 25 10:17:01.59: [ 2488]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]May 25 10:17:01.71: [ 2488]: --> [2:OK]May 25 10:17:01.71: [ 2488]: <-- [16:AT+FLID="NACMA"\r]May 25 10:17:01.82: [ 2488]: --> [2:OK]May 25 10:17:01.82: [ 2488]: DIAL 7078777May 25 10:17:01.82: [ 2488]: <-- [16:ATL1M1DT7078777\r]May 25 10:17:29.38: [ 2488]: --> [5:+FCON]May 25 10:18:09.38: [ 2488]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)May 25 10:18:09.38: [ 2488]: SEND FAILED: Unspecified Transmit Phase B errorMay 25 10:18:09.38: [ 2488]: <-- [5:ATH0\r]May 25 10:18:14.38: [ 2488]: MODEM <Timeout>May 25 10:18:14.38: [ 2488]: SESSION END
