Re: flexfax: FW: facsimile not received

[Pablo Boix <p.boix@ieee.org>]

I have a similar problem, I had to reinstall so upgraded from SuSE 6.3
to 6.4
Configured hylafax 4.1 in the same way the older one, configured the
modem.
Enabled faxgetty on inittab.
And everything seemed ok, the problem is when I receive a fax hylafax
"hungs" (when I use
SuSEfax to check status I get message receiveng fax, but the other side
hanged long time ago with
an error message. And I have to kill the process in order to make the
modem hang up.)
The modem is also a USR V-everything, the packages are the standar ones
that come with SuSE


Rimantas Zylius wrote:
> 
> hello,
> 
> i was using hylafax 4.0pl2 + Courier V-Everything, for pretty long with
> great success on mandrake6.0, box pentiumII.
> 
> for some reasons i had to make fresh install, and so i installed redhat6.2
> with hylafax 4.1beta.
> 
> all goes well, but i am unable receive faxes (i should note - on the same
> hardware) - look at the log. fax machine, that send fax thinks that all goes
> well, page is transmitted. but after page is sent some negotiations takes
> place, and fax machine indicates "Line error".
> 
> what is it all about?
> 
> rimantas
> 
> > > From:       The HylaFAX Receive Agent
> > > Sent:       2000 m. Gegužė 1 d. 16:27
> > > To:         FAXMASTER
> > > Subject:    facsimile not received
> > >
> > > An attempt to receive facsimile on ttyS2 failed because:
> > >
> > >     Normal and proper end of connection
> > >
> > >     ---- Transcript of session follows ----
> > >
> > > May 01 20:26:03.50: [  773]: SESSION BEGIN 00000010 3702395067
> > > May 01 20:26:03.50: [  773]: <-- [4:ATA\r]
> > > May 01 20:26:13.10: [  773]: --> [5:+FCON]
> > > May 01 20:26:13.10: [  773]: ANSWER: FAX CONNECTION
> > > May 01 20:26:13.10: [  773]: RECV FAX: begin
> > > May 01 20:26:27.14: [  773]: --> [5:+FCON]
> > > May 01 20:26:29.39: [  773]: --> [32:+FTSI: "          +370 2 395067"]
> > > May 01 20:26:29.39: [  773]: REMOTE TSI "+370 2 395067"
> > > May 01 20:26:29.66: [  773]: --> [21:+FDCS:0,3,0,2,0,0,0,5]
> > > May 01 20:26:29.66: [  773]: REMOTE wants 9600 bit/s
> > > May 01 20:26:29.66: [  773]: REMOTE wants page width 1728 pixels in
> > > 215 mm
> > > May 01 20:26:29.66: [  773]: REMOTE wants unlimited page length
> > > May 01 20:26:29.66: [  773]: REMOTE wants 3.85 line/mm
> > > May 01 20:26:29.66: [  773]: REMOTE wants 1-D MR
> > > May 01 20:26:31.79: [  773]: --> [2:OK]
> > > May 01 20:26:31.79: [  773]: <-- [7:AT+FDR\r]
> > > May 01 20:26:31.90: [  773]: --> [5:+FCFR]
> > > May 01 20:26:33.16: [  773]: --> [7:CONNECT]
> > > May 01 20:26:33.16: [  773]: RECV: begin page
> > > May 01 20:26:33.16: [  773]: RECV: send trigger 021
> > > May 01 20:27:01.20: [  773]: RECV: 213 total lines, 212 bad lines, 93
> > > consecutive bad lines
> > > May 01 20:27:01.20: [  773]: --> [8:+FPTS:1 ]
> > > May 01 20:27:02.37: [  773]: --> [7:+FET:2 ]
> > > May 01 20:27:02.37: [  773]: RECV recv EOP (no more pages or
> > > documents)
> > > May 01 20:27:02.37: [  773]: --> [2:OK]
> > > May 01 20:27:02.37: [  773]: RECV: REJECT page quality, 0% good lines
> > > (95% required)
> > > May 01 20:27:02.37: [  773]: RECV send RTN (retrain negative)
> > > May 01 20:27:02.37: [  773]: <-- [10:AT+FPTS=2\r]
> > > May 01 20:27:02.49: [  773]: --> [2:OK]
> > > May 01 20:27:02.49: [  773]: <-- [7:AT+FDR\r]
> > > May 01 20:27:06.24: [  773]: --> [8:+FHNG:0 ]
> > > May 01 20:27:06.24: [  773]: REMOTE HANGUP: Normal and proper end of
> > > connection (code 0)
> > > May 01 20:27:06.24: [  773]: RECV FAX (00000010): recvq/fax00010.tif
> > > from +370 2 395067, route to <unspecified>, 0 pages in 0:53
> > > May 01 20:27:06.25: [  773]: RECV FAX: Normal and proper end of
> > > connection
> > > May 01 20:27:06.25: [  773]: RECV FAX (00000010): session with +370 2
> > > 395067 terminated abnormally: Normal and proper end of connection
> > > May 01 20:27:06.25: [  773]: RECV FAX: bin/faxrcvd
> > > "recvq/fax00010.tif" "ttyS2" "00000010" "Normal and proper end of
> > > connection"
> > >
> >