|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: facsimile not received (fwd)
Noisy line? Your modem appears to be retraining (changing parameters for
better communication), and failing. Try a lower bit rate than 14400 or
consult your modem manual to see if you can program safe defaults into the
EEPROM. Also, try with a local modem (same building or neighbour).
Regards
--Louis <louis@bertrandtech.on.ca>
Louis Bertrand http://www.bertrandtech.on.ca/
Bertrand Technical Services, Bowmanville, ON, Canada
OpenBSD: Secure by default. http://www.openbsd.org/
On Mon, 24 Jan 2000, Jose Pedro Pereira wrote:
>
> I just get this message when I try to receive a Fax... May you help me
> out...
>
> I have mandrake 6.1, hylafax-v4.0pl2 and a Zoom 14.4 VFX External modem...
> My config.fax file looks as follows:
>
> CountryCode: 351
> AreaCode: 21
> FAXNumber: "+351 21 *******"
> LongDistancePrefix: ""
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0644
> LogFileMode: 0644
> DeviceMode: 0600
> RingsBeforeAnswer: 3
> SpeakerVolume: low
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "SITAF S.A. from the Network Fax Server"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%p of %%t"
> MaxRecvPages: 25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class1 # use class 1 interface
> ModemRate: 19200
> ModemFlowControl: xonxoff
> #
> ModemNoFlowCmd: AT&K # disable flow control cmd
> ModemHardFlowCmd: AT&K3 # hardware flow control cmd
> ModemSoftFlowCmd: AT&K4 # software flow control cmd
> ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)r1: AT&C1 # setup so DCD reflects carrier (or not)c1
> AdaptiveAnswer: yes
> AnswerRotary: "fax data"
> ModemAnswerCmd: AT+FCLASS=1;A
> ModemAnswerDataCmd: ATH+FCLASS=0;A
> Class1RecvIdentTimer: 10000
> ModemSetupAACmd: AT+FAA=0 # in case modem supports Class 2 also
> #
> ModemMfrQueryCmd: !Rockwell # no way to query modem
> ModemModelQueryCmd: !RC32ACL # not always right
> ModemRevQueryCmd: ATI3
> #
> ModemSendFillOrder: LSB2MSB
> ModemRecvFillOrder: MSB2LSB
>
>
>
>
>
> ---------- Forwarded message ----------
> Date: 24 Jan 2000 14:16:31 -0000
> From: The HylaFAX Receive Agent <fax@mail.net.sitaf.pt>
> To: FaxMaster@mail.net.sitaf.pt
> Subject: facsimile not received
>
> An attempt to receive facsimile on fax failed because:
>
> COMREC received DCN
>
> ---- Transcript of session follows ----
>
> Jan 24 14:15:50.10: [ 759]: SESSION BEGIN 00000007 351218420031
> Jan 24 14:15:50.10: [ 759]: <-- [14:AT+FCLASS=1;A\r]
> Jan 24 14:15:55.55: [ 759]: --> [7:CONNECT]
> Jan 24 14:15:55.55: [ 759]: ANSWER: FAX CONNECTION
> Jan 24 14:15:55.55: [ 759]: RECV FAX: begin
> Jan 24 14:15:57.15: [ 759]: --> [7:CONNECT]
> Jan 24 14:15:57.63: [ 759]: --> [2:OK]
> Jan 24 14:15:57.63: [ 759]: <-- [9:AT+FRH=3\r]
> Jan 24 14:15:58.01: [ 759]: --> [7:CONNECT]
> Jan 24 14:15:59.38: [ 759]: --> [2:OK]
> Jan 24 14:15:59.38: [ 759]: REMOTE TSI "351218461211"
> Jan 24 14:15:59.38: [ 759]: <-- [9:AT+FRH=3\r]
> Jan 24 14:15:59.40: [ 759]: --> [7:CONNECT]
> Jan 24 14:15:59.70: [ 759]: --> [2:OK]
> Jan 24 14:15:59.70: [ 759]: REMOTE wants 14400 bit/s
> Jan 24 14:15:59.70: [ 759]: REMOTE wants page width 1728 pixels in 215 mm
> Jan 24 14:15:59.70: [ 759]: REMOTE wants unlimited page length
> Jan 24 14:15:59.70: [ 759]: REMOTE wants 3.85 line/mm
> Jan 24 14:15:59.70: [ 759]: REMOTE wants 2-D MR
> Jan 24 14:15:59.70: [ 759]: RECV training at v.17 14400 bit/s
> Jan 24 14:15:59.70: [ 759]: <-- [11:AT+FRM=145\r]
> Jan 24 14:16:01.40: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:02.97: [ 759]: RECV: TCF 2785 bytes, 2% non-zero, 2702 zero-run
> Jan 24 14:16:02.97: [ 759]: --> [10:NO CARRIER]
> Jan 24 14:16:02.97: [ 759]: DELAY 75 ms
> Jan 24 14:16:03.05: [ 759]: <-- [9:AT+FTH=3\r]
> Jan 24 14:16:03.09: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:04.37: [ 759]: --> [2:OK]
> Jan 24 14:16:04.37: [ 759]: TRAINING succeeded
> Jan 24 14:16:04.37: [ 759]: <-- [11:AT+FRM=146\r]
> Jan 24 14:16:05.04: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:05.04: [ 759]: RECV: begin page
> Jan 24 14:16:26.50: [ 759]: RECV: 1463 total lines, 1346 bad lines, 124 consecutive bad lines
> Jan 24 14:16:26.50: [ 759]: RECV: REJECT page quality, 7% good lines (95% required)
> Jan 24 14:16:26.50: [ 759]: RECV: end page
> Jan 24 14:16:26.50: [ 759]: --> [10:NO CARRIER]
> Jan 24 14:16:26.50: [ 759]: <-- [9:AT+FRH=3\r]
> Jan 24 14:16:26.85: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:27.65: [ 759]: --> [2:OK]
> Jan 24 14:16:27.65: [ 759]: RECV recv EOP (no more pages or documents)
> Jan 24 14:16:27.65: [ 759]: <-- [9:AT+FTH=3\r]
> Jan 24 14:16:27.71: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:28.99: [ 759]: --> [2:OK]
> Jan 24 14:16:28.99: [ 759]: RECV send RTN (retrain negative)
> Jan 24 14:16:28.99: [ 759]: <-- [9:AT+FRH=3\r]
> Jan 24 14:16:29.35: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:30.27: [ 759]: --> [2:OK]
> Jan 24 14:16:30.27: [ 759]: RECV recv DCN
> Jan 24 14:16:30.27: [ 759]: RECV FAX (00000007): recvq/fax00003.tif from 351218461211, route to <unspecified>, 0 pages in 0:35
> Jan 24 14:16:30.27: [ 759]: RECV FAX: COMREC received DCN
> Jan 24 14:16:30.27: [ 759]: <-- [9:AT+FTH=3\r]
> Jan 24 14:16:30.33: [ 759]: --> [7:CONNECT]
> Jan 24 14:16:31.61: [ 759]: --> [2:OK]
> Jan 24 14:16:31.61: [ 759]: RECV FAX (00000007): session with 351218461211 terminated abnormally: COMREC received DCN
> Jan 24 14:16:31.61: [ 759]: RECV FAX: bin/faxrcvd "recvq/fax00003.tif" "fax" "00000007" "COMREC received DCN"
>
>
>
