|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Just curious
Hello,
Just curious. I was having a fax success rate of about 3% . This is
one of the successful ones. I've since got my config.ttyS1 working. I'm just
wondering, how did this fax get out with "input flow NONE, output flow NONE"?
This is from /var/spool/fax/mail/c0000041
file
Thanks
George
Jan 02
09:14:13.72: [ 1955]: SESSION BEGIN 00000041 70952580635
Jan 02 09:14:13.72: [ 1955]: SEND FAX: JOB 30 DEST 258-0635 COMMID 00000041
Jan 02 09:14:13.72: [ 1955]: MODEM set DTR OFF
Jan 02 09:14:13.72: [ 1955]: DELAY 2600 ms
Jan 02 09:14:16.32: [ 1955]: MODEM set DTR ON
Jan 02 09:14:16.32: [ 1955]: MODEM set baud rate: 19200 baud, input flow NONE, output flow NONE
Jan 02 09:14:16.32: [ 1955]: MODEM flush i/o
Jan 02 09:14:16.32: [ 1955]: <-- [15:ATE0V1Q0S0=0H0\r]
Jan 02 09:14:16.36: [ 1955]: --> [2:OK]
Jan 02 09:14:16.36: [ 1955]: <-- [12:ATS8=2S7=60\r]
Jan 02 09:14:16.37: [ 1955]: --> [2:OK]
Jan 02 09:14:16.37: [ 1955]: <-- [12:AT+FCLASS=1\r]
Jan 02 09:14:16.38: [ 1955]: --> [2:OK]
Jan 02 09:14:16.38: [ 1955]: <-- [5:ATM0\r]
Jan 02 09:14:16.39: [ 1955]: --> [2:OK]
Jan 02 09:14:16.39: [ 1955]: MODEM input buffering enabled
Jan 02 09:14:16.39: [ 1955]: <-- [12:AT+FCLASS=1\r]
Jan 02 09:14:16.50: [ 1955]: --> [2:OK]
Jan 02 09:14:16.50: [ 1955]: DIAL 2580635
Jan 02 09:14:16.50: [ 1955]: <-- [13:ATDP2580635@\r]
Jan 02 09:14:42.82: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:42.82: [ 1955]: MODEM input buffering disabled
Jan 02 09:14:45.26: [ 1955]: --> [2:OK]
Jan 02 09:14:45.26: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:14:45.27: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:46.04: [ 1955]: --> [2:OK]
Jan 02 09:14:46.04: [ 1955]: REMOTE CSI "+7095 258 0635"
Jan 02 09:14:46.04: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:14:46.05: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:46.45: [ 1955]: --> [2:OK]
Jan 02 09:14:46.45: [ 1955]: REMOTE best rate 14400 bit/s
Jan 02 09:14:46.45: [ 1955]: REMOTE max page width 2432 pixels in 303 mm
Jan 02 09:14:46.45: [ 1955]: REMOTE max unlimited page length
Jan 02 09:14:46.45: [ 1955]: REMOTE best vres 7.7 line/mm
Jan 02 09:14:46.45: [ 1955]: REMOTE best format 2-D MMR
Jan 02 09:14:46.45: [ 1955]: REMOTE supports T.30 Annex A, ECM
Jan 02 09:14:46.45: [ 1955]: REMOTE best 0 ms/scanline
Jan 02 09:14:46.45: [ 1955]: USE 14400 bit/s
Jan 02 09:14:46.45: [ 1955]: USE 0 ms/scanline
Jan 02 09:14:46.45: [ 1955]: SEND file "docq/doc29.ps;00"
Jan 02 09:14:46.45: [ 1955]: USE page width 1728 pixels in 215 mm
Jan 02 09:14:46.45: [ 1955]: USE unlimited page length
Jan 02 09:14:46.45: [ 1955]: USE 3.85 line/mm
Jan 02 09:14:46.45: [ 1955]: USE 1-D MR
Jan 02 09:14:46.45: [ 1955]: SEND training at v.17 14400 bit/s
Jan 02 09:14:46.45: [ 1955]: <-- [9:AT+FTH=3\r]
Jan 02 09:14:47.39: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:47.39: [ 1955]: <-- data [23]
Jan 02 09:14:47.39: [ 1955]: <-- data [2]
Jan 02 09:14:47.41: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:47.41: [ 1955]: <-- data [6]
Jan 02 09:14:47.41: [ 1955]: <-- data [2]
Jan 02 09:14:48.49: [ 1955]: --> [2:OK]
Jan 02 09:14:48.49: [ 1955]: DELAY 75 ms
Jan 02 09:14:48.57: [ 1955]: <-- [11:AT+FTM=145\r]
Jan 02 09:14:48.59: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:48.59: [ 1955]: <-- data [1024]
Jan 02 09:14:48.59: [ 1955]: <-- data [1024]
Jan 02 09:14:48.59: [ 1955]: <-- data [652]
Jan 02 09:14:48.59: [ 1955]: <-- data [2]
Jan 02 09:14:51.72: [ 1955]: --> [2:OK]
Jan 02 09:14:51.72: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:14:51.84: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:52.97: [ 1955]: --> [2:OK]
Jan 02 09:14:52.97: [ 1955]: TRAINING succeeded
Jan 02 09:14:52.97: [ 1955]: <-- [11:AT+FTM=146\r]
Jan 02 09:14:53.06: [ 1955]: --> [7:CONNECT]
Jan 02 09:14:53.06: [ 1955]: SEND begin page
Jan 02 09:14:53.06: [ 1955]: <-- data [1028]
Jan 02 09:14:53.06: [ 1955]: <-- data [1028]
Jan 02 09:14:53.06: [ 1955]: <-- data [1029]
Jan 02 09:14:53.06: [ 1955]: <-- data [1025]
Jan 02 09:14:54.26: [ 1955]: <-- data [1027]
Jan 02 09:14:54.26: [ 1955]: <-- data [1026]
Jan 02 09:14:54.26: [ 1955]: <-- data [1028]
Jan 02 09:14:54.26: [ 1955]: <-- data [1027]
Jan 02 09:14:55.85: [ 1955]: <-- data [1029]
Jan 02 09:14:55.86: [ 1955]: <-- data [1028]
Jan 02 09:14:55.86: [ 1955]: <-- data [1028]
Jan 02 09:14:55.86: [ 1955]: <-- data [1026]
Jan 02 09:14:58.04: [ 1955]: <-- data [1030]
Jan 02 09:14:58.04: [ 1955]: <-- data [1028]
Jan 02 09:14:58.04: [ 1955]: <-- data [1026]
Jan 02 09:14:58.04: [ 1955]: <-- data [1025]
Jan 02 09:15:00.14: [ 1955]: <-- data [1028]
Jan 02 09:15:00.14: [ 1955]: <-- data [1027]
Jan 02 09:15:00.14: [ 1955]: <-- data [1026]
Jan 02 09:15:02.24: [ 1955]: <-- data [970]
Jan 02 09:15:02.24: [ 1955]: SENT 20425 bytes of data
Jan 02 09:15:02.24: [ 1955]: SEND 1D RTC
Jan 02 09:15:02.24: [ 1955]: <-- data [29]
Jan 02 09:15:02.24: [ 1955]: <-- data [2]
Jan 02 09:15:02.24: [ 1955]: SEND end page
Jan 02 09:15:04.80: [ 1955]: --> [2:OK]
Jan 02 09:15:04.80: [ 1955]: DELAY 75 ms
Jan 02 09:15:04.88: [ 1955]: SEND send MPS (more pages, same document)
Jan 02 09:15:04.88: [ 1955]: <-- [9:AT+FTH=3\r]
Jan 02 09:15:05.74: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:05.74: [ 1955]: <-- data [3]
Jan 02 09:15:05.74: [ 1955]: <-- data [2]
Jan 02 09:15:06.06: [ 1955]: --> [2:OK]
Jan 02 09:15:06.06: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:15:06.31: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:07.47: [ 1955]: --> [2:OK]
Jan 02 09:15:07.47: [ 1955]: SEND recv MCF (message confirmation)
Jan 02 09:15:07.47: [ 1955]: SEND FAX (00000041): FROM root@george.hello TO 258-0635 (page 1 of 3 sent in 0:21)
Jan 02 09:15:07.47: [ 1955]: USE page width 1728 pixels in 215 mm
Jan 02 09:15:07.47: [ 1955]: USE unlimited page length
Jan 02 09:15:07.47: [ 1955]: USE 3.85 line/mm
Jan 02 09:15:07.47: [ 1955]: USE 1-D MR
Jan 02 09:15:07.47: [ 1955]: <-- [11:AT+FTM=146\r]
Jan 02 09:15:07.56: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:07.56: [ 1955]: SEND begin page
Jan 02 09:15:07.56: [ 1955]: <-- data [1029]
Jan 02 09:15:07.56: [ 1955]: <-- data [1026]
Jan 02 09:15:07.56: [ 1955]: <-- data [1029]
Jan 02 09:15:07.56: [ 1955]: <-- data [1026]
Jan 02 09:15:08.76: [ 1955]: <-- data [1027]
Jan 02 09:15:08.76: [ 1955]: <-- data [1024]
Jan 02 09:15:08.76: [ 1955]: <-- data [1027]
Jan 02 09:15:08.76: [ 1955]: <-- data [1026]
Jan 02 09:15:10.35: [ 1955]: <-- data [1026]
Jan 02 09:15:10.35: [ 1955]: <-- data [1028]
Jan 02 09:15:10.35: [ 1955]: <-- data [1030]
Jan 02 09:15:10.35: [ 1955]: <-- data [1024]
Jan 02 09:15:12.51: [ 1955]: <-- data [1028]
Jan 02 09:15:12.51: [ 1955]: <-- data [1027]
Jan 02 09:15:12.51: [ 1955]: <-- data [1027]
Jan 02 09:15:12.51: [ 1955]: <-- data [1025]
Jan 02 09:15:14.61: [ 1955]: <-- data [1030]
Jan 02 09:15:14.61: [ 1955]: <-- data [1033]
Jan 02 09:15:14.61: [ 1955]: <-- data [1027]
Jan 02 09:15:16.78: [ 1955]: <-- data [375]
Jan 02 09:15:16.78: [ 1955]: SENT 19831 bytes of data
Jan 02 09:15:16.78: [ 1955]: SEND 1D RTC
Jan 02 09:15:16.78: [ 1955]: <-- data [29]
Jan 02 09:15:16.78: [ 1955]: <-- data [2]
Jan 02 09:15:16.78: [ 1955]: SEND end page
Jan 02 09:15:18.98: [ 1955]: --> [2:OK]
Jan 02 09:15:18.98: [ 1955]: DELAY 75 ms
Jan 02 09:15:19.06: [ 1955]: SEND send MPS (more pages, same document)
Jan 02 09:15:19.06: [ 1955]: <-- [9:AT+FTH=3\r]
Jan 02 09:15:19.92: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:19.92: [ 1955]: <-- data [3]
Jan 02 09:15:19.92: [ 1955]: <-- data [2]
Jan 02 09:15:20.24: [ 1955]: --> [2:OK]
Jan 02 09:15:20.24: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:15:20.51: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:21.68: [ 1955]: --> [2:OK]
Jan 02 09:15:21.68: [ 1955]: SEND recv MCF (message confirmation)
Jan 02 09:15:21.68: [ 1955]: SEND FAX (00000041): FROM root@george.hello TO 258-0635 (page 2 of 3 sent in 0:14)
Jan 02 09:15:21.68: [ 1955]: USE page width 1728 pixels in 215 mm
Jan 02 09:15:21.68: [ 1955]: USE unlimited page length
Jan 02 09:15:21.68: [ 1955]: USE 3.85 line/mm
Jan 02 09:15:21.68: [ 1955]: USE 1-D MR
Jan 02 09:15:21.68: [ 1955]: <-- [11:AT+FTM=146\r]
Jan 02 09:15:21.77: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:21.77: [ 1955]: SEND begin page
Jan 02 09:15:21.77: [ 1955]: <-- data [1031]
Jan 02 09:15:21.77: [ 1955]: <-- data [1027]
Jan 02 09:15:21.77: [ 1955]: <-- data [1032]
Jan 02 09:15:21.77: [ 1955]: <-- data [1025]
Jan 02 09:15:22.97: [ 1955]: <-- data [1027]
Jan 02 09:15:22.97: [ 1955]: <-- data [1033]
Jan 02 09:15:22.97: [ 1955]: <-- data [1030]
Jan 02 09:15:22.97: [ 1955]: <-- data [1031]
Jan 02 09:15:24.56: [ 1955]: <-- data [1030]
Jan 02 09:15:24.57: [ 1955]: <-- data [192]
Jan 02 09:15:24.57: [ 1955]: SENT 9408 bytes of data
Jan 02 09:15:24.57: [ 1955]: SEND 1D RTC
Jan 02 09:15:24.57: [ 1955]: <-- data [29]
Jan 02 09:15:24.57: [ 1955]: <-- data [2]
Jan 02 09:15:24.57: [ 1955]: SEND end page
Jan 02 09:15:27.39: [ 1955]: --> [2:OK]
Jan 02 09:15:27.39: [ 1955]: DELAY 95 ms
Jan 02 09:15:27.49: [ 1955]: SEND send EOP (no more pages or documents)
Jan 02 09:15:27.49: [ 1955]: <-- [9:AT+FTH=3\r]
Jan 02 09:15:28.35: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:28.35: [ 1955]: <-- data [3]
Jan 02 09:15:28.35: [ 1955]: <-- data [2]
Jan 02 09:15:28.67: [ 1955]: --> [2:OK]
Jan 02 09:15:28.67: [ 1955]: <-- [9:AT+FRH=3\r]
Jan 02 09:15:28.95: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:30.12: [ 1955]: --> [2:OK]
Jan 02 09:15:30.12: [ 1955]: SEND recv MCF (message confirmation)
Jan 02 09:15:30.12: [ 1955]: SEND FAX (00000041): FROM root@george.hello TO 258-0635 (page 3 of 3 sent in 0:09)
Jan 02 09:15:30.12: [ 1955]: SEND FAX (00000041): FROM root@george.hello TO 258-0635 (docq/doc29.ps;00 sent in 0:44)
Jan 02 09:15:30.12: [ 1955]: <-- [9:AT+FTH=3\r]
Jan 02 09:15:31.06: [ 1955]: --> [7:CONNECT]
Jan 02 09:15:31.06: [ 1955]: <-- data [3]
Jan 02 09:15:31.06: [ 1955]: <-- data [2]
Jan 02 09:15:31.38: [ 1955]: --> [2:OK]
Jan 02 09:15:31.38: [ 1955]: MODEM input buffering enabled
Jan 02 09:15:31.38: [ 1955]: <-- [5:ATH0\r]
Jan 02 09:15:32.53: [ 1955]: --> [2:OK]
Jan 02 09:15:32.53: [ 1955]: MODEM set DTR OFF
Jan 02 09:15:32.53: [ 1955]: SESSION END
--
My personal website
http://www.firstnethou.com/gz/welcome.ht
