|
Report any problems to
webmaster@hylafax.org
HylaFAX is a trademark of Silicon Graphics Corporation. Internet connectivity for hylafax.org is provided by: VirtuALL Private Host Services |
| Hylafax Mailing List Archives |
Thanks Frank
Jan 12 19:44:03 earth FaxGetty[226]: RECV FAX (00000040):
from Acer America, page 1 in 0:17, INF, 7.7 line/mm, 1-D MR
Jan 12 19:44:03 earth FaxGetty[226]: RECV FAX (00000040):
recvq/fax00046.tif from Acer America, route to <unspecified>, 1 pages
in 0:19
Jan 12 19:44:15 earth kernel: Creative SBLive! at 0xd000
on irq 10
Jan 12 19:44:27 earth modprobe: modprobe: Can't locate
module char-major-15
Jan 12 19:44:27 earth modprobe: modprobe: Can't locate
module char-major-15
Jan 12 19:44:48 earth FaxGetty[226]: RECV FAX (00000040):
from Acer America, page 1 in 0:45, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:07 earth FaxGetty[226]: RECV FAX (00000040):
from Acer America, page 2 in 0:19, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:31 earth FaxGetty[226]: RECV FAX (00000040):
from Acer America, page 3 in 0:24, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:49 earth FaxGetty[226]: RECV FAX (00000040):
recvq/fax00047.tif from Acer America, route to <unspecified>, 3 pages
in 1:46
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX: bin/faxrcvd
"recvq/fax00046.tif" "modem" "00000040" ""
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX (00000040):
session with Acer America terminated abnormally: Unspecified Phase C error,
including too much delay between TCF and +FDR command
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX: bin/faxrcvd
"recvq/fax00047.tif" "modem" "00000040" "Unspecified Phase C error, including
too much delay between TCF and +FDR command"
CountryCode:
1
AreaCode:
780
FAXNumber:
+1.780.488.xxx
LongDistancePrefix: 1
InternationalPrefix:
011
DialStringRules:
etc/dialrules
ServerTracing:
1
SessionTracing:
11
RecvFileMode:
0644
LogFileMode:
0600
DeviceMode:
0600
RingsBeforeAnswer: 1
SpeakerVolume:
on
GettyArgs:
"-h %l dx_%s"
LocalIdentifier:
"gelly"
TagLineFont:
etc/lutRS18.pcf
TagLineFormat:
"From %%l|%c|Page %%p of %%t"
QualifyTSI:
""
MaxRecvPages:
25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:
Class2.0 # use this to supply
a hint
ModemRate:
38400
ModemFlowControl:
rtscts
ModemSetupDTRCmd:
ATS13=1&D2 # setup so DTR drop resets
modem
ModemSetupDCDCmd:
AT&C1 #
setup so DCD reflects carrier (or not)
Class2RecvDataTrigger: "\022"
#
# We normally append the "@" symbol to the dial string
so that
# the modem will wait 5 seconds before attempting to
connect
# and return result codes that distinguish between no
carrier
# and no answer. This makes it possible to avoid
problems with
# repeatedly dialing a number that doesn't have a fax
machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through
a PBX,
# put it in the ModemDialCmd;
e.g. "DT9%s@".
#
ModemDialCmd:
ATDT%s # T for tone
dialing
#
# Other possible configuration stuff. The default
strings are
# shown below. Only those that are different from
the defaults
# need to be included in the configuration file.
#
ModemResetCmds:
""
# stuff to do when modem is reset
ModemAnswerCmd:
ATA
# use this to answer phone
ModemNoAutoAnswerCmd: ATS0=0
# disable auto-answer
ModemNoFlowCmd:
AT&H0&I0&R1
ModemHardFlowCmd:
AT&H1&I0&R2
ModemSoftFlowCmd:
AT&H2&I2&R1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM
HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0
ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:
ATE0
# disable command echo
ModemVerboseResultsCmd: ATV1
# enable verbose command results
ModemResultCodesCmd: ATQ0X4
ModemOnHookCmd:
ATH0
# place phone on hook (hangup)
ModemSoftResetCmd: ATZ
# do soft reset of modem
ModemWaitTimeCmd:
ATS7=60 # wait 60 seconds
for carrier
ModemCommaPauseTimeCmd: ATS8=2
# comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB
# bit order of received facsimile
ModemSendFillOrder: LSB2MSB
# bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:
AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd:
AT+FBO=0 # bit order for phase
B/C/D (direct)
Class2CQCmd:
""
# commands to enable copy quality proc.
Class2AbortCmd:
AT+FKS # abort session
command
Class2CQQueryCmd:
!(0),(0) # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=?
# query for modem capabilities
Class2TBCCmd:
AT+FPP=0 # setup stream mode
Class2CRCmd:
AT+FCR=1 # enable capability
to receive
Class2PHCTOCmd:
AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd:
AT+FBU=0 # enable HDLC frame
tracing
Class2LIDCmd:
AT+FLI # set local
identifier command
Class2DCCCmd:
AT+FCC # set modem
capabilities command
Class2DISCmd:
AT+FIS # set session
parameters command
Class2DDISCmd:
""
# disable pre-dial DIS command hack
Class2CIGCmd:
AT+FPI # set polling
identifier command
Class2NRCmd:
AT+FNR=1,1,1,0 # setup status reporting command
Class2PIECmd:
""
Class2PTSCmd:
AT+FPS # set post-page
status command
Class2SPLCmd:
AT+FSP # set polling
indicator command
Class2NFLOCmd:
AT+FLO=0 # set no flow control
command
Class2SFLOCmd:
AT+FLO=1 # set software flow
control command
Class2HFLOCmd:
AT+FLO=2 # set hardware flow
control command
|
|
|