|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Unspecified Transmit Phase B error
Hi
hylafax-4.1beta1 under RedHat 5 using precompiled rpm from sgi.com
MODEM ZYXEL U1496
Week back all worked (send and receive)
Now I can not understand a problem (not send and not receive)
I have touched variants (Fax Class 1, 2, 2.0)
Lowered speed of the modem
Put and configure other modem (GVC 1440 FAX/MODEM)
Result same
I need Help
--- config.ttyS1 there ---
skip...
ModemType: Class2
ModemRate: 38400
ModemFlowControl: rtscts
ModemNoFlowCmd: AT&H0
ModemHardFlowCmd: AT&H3
ModemSoftFlowCmd: AT&H4
ModemSetupDTRCmd: AT&D2
ModemSetupDCDCmd: AT&C1
ModemSetupAACmd: AT+FAA=1
ModemSendFillOrder: LSB2MSB
ModemRecvFillOrder: MSB2LSB
Class2RecvDataTrigger: "\022"
ModemResetCmds: AT&B1&N0&S0*F0S18=2S38.3=1S39=0
ModemDialCmd: ATDP%s
ModemSetVolumeCmd: "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
PagerSetupCmds: AT&K0&N15 # use V.22 at 1200 bps (PageNet)
---- Log file there ---
Jan 10 12:52:11.52: [32537]: SESSION BEGIN 00000011 380442209757
Jan 10 12:52:11.53: [32537]: SEND FAX: JOB 1 DEST 220-9757 COMMID 00000011
Jan 10 12:52:11.53: [32537]: MODEM set DTR OFF
Jan 10 12:52:11.53: [32537]: DELAY 2600 ms
Jan 10 12:52:14.12: [32537]: MODEM set DTR ON
Jan 10 12:52:14.12: [32537]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Jan 10 12:52:14.12: [32537]: MODEM flush i/o
Jan 10 12:52:14.12: [32537]: <-- [44:AT&B1&N0&S0*F0S18=2S38.3=1S39=0E0V1Q0S0=0H0\r]
Jan 10 12:52:14.34: [32537]: --> [2:OK]
Jan 10 12:52:14.34: [32537]: <-- [22:ATS8=2S7=120&H3&D2&C1\r]
Jan 10 12:52:14.36: [32537]: --> [2:OK]
Jan 10 12:52:14.36: [32537]: <-- [12:AT+FCLASS=2\r]
Jan 10 12:52:14.49: [32537]: --> [2:OK]
Jan 10 12:52:14.49: [32537]: <-- [10:AT+FTBC=0\r]
Jan 10 12:52:14.50: [32537]: --> [2:OK]
Jan 10 12:52:14.50: [32537]: <-- [10:AT+FBOR=0\r]
Jan 10 12:52:14.51: [32537]: --> [2:OK]
Jan 10 12:52:14.51: [32537]: <-- [13:AT+FPHCTO=30\r]
Jan 10 12:52:14.53: [32537]: --> [2:OK]
Jan 10 12:52:14.53: [32537]: <-- [10:AT+FBUG=1\r]
Jan 10 12:52:14.54: [32537]: --> [2:OK]
Jan 10 12:52:14.54: [32537]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Jan 10 12:52:14.56: [32537]: --> [2:OK]
Jan 10 12:52:14.56: [32537]: <-- [7:ATM1L5\r]
Jan 10 12:52:14.57: [32537]: --> [2:OK]
Jan 10 12:52:14.57: [32537]: MODEM input buffering enabled
Jan 10 12:52:14.57: [32537]: <-- [12:AT+FCLASS=2\r]
Jan 10 12:52:14.80: [32537]: --> [2:OK]
Jan 10 12:52:14.80: [32537]: <-- [10:AT+FTBC=0\r]
Jan 10 12:52:14.91: [32537]: --> [2:OK]
Jan 10 12:52:14.91: [32537]: <-- [10:AT+FBOR=0\r]
Jan 10 12:52:15.02: [32537]: --> [2:OK]
Jan 10 12:52:15.02: [32537]: <-- [13:AT+FPHCTO=30\r]
Jan 10 12:52:15.14: [32537]: --> [2:OK]
Jan 10 12:52:15.14: [32537]: <-- [10:AT+FBUG=1\r]
Jan 10 12:52:15.25: [32537]: --> [2:OK]
Jan 10 12:52:15.25: [32537]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Jan 10 12:52:15.37: [32537]: --> [2:OK]
Jan 10 12:52:15.37: [32537]: <-- [31:AT+FLID="Infinservice FaxServ"\r]
Jan 10 12:52:15.49: [32537]: --> [2:OK]
Jan 10 12:52:15.54: [32537]: DIAL 2209757
Jan 10 12:52:15.54: [32537]: <-- [12:ATDP2209757\r]
Jan 10 12:52:43.40: [32537]: --> [5:+FCON]
Jan 10 12:52:43.40: [32537]: --> [118:+FNSF:00 00 0E 00 00 00 96 0F 01 03 00 10 05 02 95 C8 08 01 49 02 49 6E 66 69 6E 73 65 72 76
69 63 65 2C 20 4C 74 03 ]
Jan 10 12:52:43.40: [32537]: REMOTE NSF "00 00 0E 00 00 00 96 0F 01 03 00 10 05 02 95 C8 08 01 49 02 49 6E 66 69 6E 73 65 72 76 69
63 65 2C 20 4C 74 03"
Jan 10 12:52:43.55: [32537]: --> [27:+FCSI: 38 044 2209757 ]
Jan 10 12:52:43.55: [32537]: REMOTE CSI "38 044 2209757"
Jan 10 12:52:43.55: [32537]: --> [21:+FDIS:1,3,0,2,1,0,0,4]
Jan 10 12:52:43.55: [32537]: --> [2:OK]
Jan 10 12:52:43.55: [32537]: REMOTE best rate 9600 bit/s
Jan 10 12:52:43.55: [32537]: REMOTE max page width 1728 pixels in 215 mm
Jan 10 12:52:43.55: [32537]: REMOTE max unlimited page length
Jan 10 12:52:43.55: [32537]: REMOTE best vres 7.7 line/mm
Jan 10 12:52:43.55: [32537]: REMOTE best format 2-D MR
Jan 10 12:52:43.55: [32537]: REMOTE best 20 ms, 10 ms/scanline
Jan 10 12:52:43.55: [32537]: USE 9600 bit/s
Jan 10 12:52:43.55: [32537]: USE 20 ms, 10 ms/scanline
Jan 10 12:52:43.55: [32537]: SEND file "docq/doc1.ps;30"
Jan 10 12:52:43.99: [32537]: USE page width 1728 pixels in 215 mm
Jan 10 12:52:43.99: [32537]: USE unlimited page length
Jan 10 12:52:43.99: [32537]: USE 3.85 line/mm
Jan 10 12:52:43.99: [32537]: USE 1-D MR
Jan 10 12:52:43.99: [32537]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,4\r]
Jan 10 12:52:50.46: [32537]: --> [8:+FHNG:20]
Jan 10 12:52:50.46: [32537]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Jan 10 12:52:50.46: [32537]: --> [2:OK]
Jan 10 12:52:50.46: [32537]: <-- [7:AT+FDT\r]
Jan 10 12:52:50.87: [32537]: --> [10:NO CARRIER]
Jan 10 12:52:50.87: [32537]: MODEM No carrier
Jan 10 12:52:50.87: [32537]: <-- [5:ATH0\r]
Jan 10 12:52:51.18: [32537]: --> [2:OK]
Jan 10 12:52:51.18: [32537]: MODEM set DTR OFF
Jan 10 12:52:51.18: [32537]: SESSION END
Best Regards
Techman
