Re: flexfax: receiving problems

["Michael Dorfmüller" <Michael@Dorfmueller.de>]

David Woolley schrieb am 04.09.1999:
>> 
>> I have a problem by receiving a fax with hylafax. 
>
>More precisely, it looks like you have a modem configuration
problem, and haven't told us what modem you are using, not to mention
>what version of hylafax, what hardware, what operating system, etc.
>
>Things to try:  flow control and bit order.
>
Dear David,

thanks for your answer.

I have a Ralley Com 336 Fax-Modem with Rockwell-Chipsatz. In
/var/log/messages it is started as " [FAXGETTY]
Modem288DPI/KA1131-00". I use SUSE Linux 6.0. with hylafax 4.0pl2.

Here is the configuration file of the modem:

# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
#
#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		049
AreaCode:		02191
FAXNumber:		+049.02191.882107
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	3
SpeakerVolume:		low
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Dorfmueller"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#

#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:		"ATX3"		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:		AT+FCLASS=2	# command to enter class 2
Class2BORCmd:		AT+FBOR=0	# bit order for phase B/C/D (direct)
Class2RELCmd:		AT+FREL=1	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FK		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FDCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FTBC=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FPHCTO=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBUG=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLID		# set local identifier command
Class2DCCCmd:		AT+FDCC		# set modem capabilities command
Class2DISCmd:		AT+FDIS		# set session parameters command
Class2DDISCmd:		AT+FDIS		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FCIG		# set polling identifier command
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2SPLCmd:		AT+FSPL		# set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send

Mit besten Gruessen 


Michael

Anwort bitte an Michael@Dorfmueller.com