Configuration: Suse
6.1
Hylafax, new version
Modem: Microlink 28.8 TQV
Problem: Receiving is ok, but
when I send an fax to an faxmachine, there is an Unspecified Transmit Phase B
error (code 20).
Here is the file
Aug 13 10:59:15.72: [ 2272]: SESSION BEGIN 00000057
0403603016428
Aug 13 10:59:15.73: [ 2272]: SEND FAX: JOB 38 DEST
00403603016428 COMMID 00000057
Aug 13 10:59:15.73: [ 2272]: DELAY 2600
ms
Aug 13 10:59:18.32: [ 2272]: <-- [15:ATE0V1Q0S0=0H0\r]
Aug 13
10:59:18.34: [ 2272]: --> [2:OK]
Aug 13 10:59:18.34: [ 2272]: <--
[21:ATS8=2S7=60&K4&D2&C1\r]
Aug 13 10:59:18.37: [ 2272]: -->
[2:OK]
Aug 13 10:59:18.37: [ 2272]: <-- [14:AT+FCLASS=2.0\r]
Aug 13
10:59:18.39: [ 2272]: --> [2:OK]
Aug 13 10:59:18.39: [ 2272]: <--
[9:AT+FLO=1\r]
Aug 13 10:59:18.41: [ 2272]: --> [2:OK]
Aug 13
10:59:18.41: [ 2272]: <-- [9:AT+FPP=0\r]
Aug 13 10:59:18.43: [ 2272]:
--> [2:OK]
Aug 13 10:59:18.43: [ 2272]: <-- [9:AT+FBO=0\r]
Aug 13
10:59:18.45: [ 2272]: --> [2:OK]
Aug 13 10:59:18.45: [ 2272]: <--
[10:AT+FCT=30\r]
Aug 13 10:59:18.47: [ 2272]: --> [2:OK]
Aug 13
10:59:18.47: [ 2272]: <-- [15:AT+FNR=1,1,1,0\r]
Aug 13 10:59:18.49: [
2272]: --> [2:OK]
Aug 13 10:59:18.49: [ 2272]: <--
[9:AT+FIE=0\r]
Aug 13 10:59:18.51: [ 2272]: --> [2:OK]
Aug 13
10:59:18.51: [ 2272]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 13
10:59:18.53: [ 2272]: --> [2:OK]
Aug 13 10:59:18.53: [ 2272]: <--
[7:ATL2M1\r]
Aug 13 10:59:18.55: [ 2272]: --> [2:OK]
Aug 13
10:59:18.55: [ 2272]: <-- [14:AT+FCLASS=2.0\r]
Aug 13 10:59:18.67: [
2272]: --> [2:OK]
Aug 13 10:59:18.67: [ 2272]: <--
[9:AT+FLO=1\r]
Aug 13 10:59:18.79: [ 2272]: --> [2:OK]
Aug 13
10:59:18.79: [ 2272]: <-- [9:AT+FPP=0\r]
Aug 13 10:59:18.91: [ 2272]:
--> [2:OK]
Aug 13 10:59:18.91: [ 2272]: <-- [9:AT+FBO=0\r]
Aug 13
10:59:19.03: [ 2272]: --> [2:OK]
Aug 13 10:59:19.03: [ 2272]: <--
[10:AT+FCT=30\r]
Aug 13 10:59:19.15: [ 2272]: --> [2:OK]
Aug 13
10:59:19.15: [ 2272]: <-- [15:AT+FNR=1,1,1,0\r]
Aug 13 10:59:19.27: [
2272]: --> [2:OK]
Aug 13 10:59:19.27: [ 2272]: <--
[9:AT+FIE=0\r]
Aug 13 10:59:19.39: [ 2272]: --> [2:OK]
Aug 13
10:59:19.39: [ 2272]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 13
10:59:19.51: [ 2272]: --> [2:OK]
Aug 13 10:59:19.51: [ 2272]: <--
[26:AT+FLI="+49.351.855.2735"\r]
Aug 13 10:59:19.64: [ 2272]: -->
[2:OK]
Aug 13 10:59:19.65: [ 2272]: DIAL 00403603016428
Aug 13
10:59:19.65: [ 2272]: <-- [21:ATX3DP00403603016428\r]
Aug 13 10:59:57.37:
[ 2272]: --> [4:+FCO]
Aug 13 10:59:59.27: [ 2272]: -->
[27:+FCI:" +49 40 3603016428"]
Aug 13 10:59:59.27: [ 2272]:
REMOTE CSI "+49 40 3603016428"
Aug 13 10:59:59.27: [ 2272]: -->
[20:+FIS:1,5,0,2,1,1,0,0]
Aug 13 10:59:59.27: [ 2272]: --> [2:OK]
Aug
13 10:59:59.27: [ 2272]: REMOTE best rate 14400 bit/s
Aug 13 10:59:59.27: [
2272]: REMOTE max page width 1728 pixels in 215 mm
Aug 13 10:59:59.27: [
2272]: REMOTE max unlimited page length
Aug 13 10:59:59.27: [ 2272]: REMOTE
best vres 7.7 line/mm
Aug 13 10:59:59.27: [ 2272]: REMOTE best format 2-D
MR
Aug 13 10:59:59.27: [ 2272]: REMOTE supports T.30 Annex A, ECM
Aug 13
10:59:59.28: [ 2272]: REMOTE best 0 ms/scanline
Aug 13 10:59:59.28: [ 2272]:
USE 14400 bit/s
Aug 13 10:59:59.28: [ 2272]: USE 0 ms/scanline
Aug 13
10:59:59.28: [ 2272]: <-- [5:ATH0\r]
Aug 13 11:00:00.89: [ 2272]: -->
[7:+FHS:20]
Aug 13 11:00:00.89: [ 2272]: REMOTE HANGUP: Unspecified Transmit
Phase B error (code 20)
Aug 13 11:00:01.79: [ 2272]: --> [2:OK]
Aug 13
11:00:01.79: [ 2272]: SESSION END
Can somebody help me
?
