flexfax: Problem with fax receiving

["Volker Krause" <krause@samuelson.de>]

I have (probably) the same problem receiveing faxes with ' faxgetty '
(HylaFAX Version 4.0pl2).
Sending a fax works fine but also I tried some settings for
ModemRecvFillOrder, ModemSendFillOrder and AT+FBOR receiving a fax results
in 'REMOTE HANGUP: Missing EOL after 5 seconds (section 3.2/T.4) (code 91)'
- Please, help

Volker K.


------ config.ttyS2 (LAST version) ------
# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $
#
# Generic Class 2 modem configuration.
#
CountryCode:  49
AreaCode:  30
FAXNumber:  +49.30.30820596
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  medium
GettyArgs:  "-h %l dx_%s"
LocalIdentifier: "Samuelson GmbH"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
MaxRecvPages:  25
#
ModemType:  Class2  # use this to supply a hint
ModemDialCmd:  ATDT%s  # T for tone dialing, @ for silence
ModemRecvFillOrder: MSB2LSB  # bit order of received facsimile
ModemSendFillOrder: MSB2LSB  # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:  AT+FCLASS=2 # command to enter class 2
Class2BORCmd:  AT+FBOR=1 # bit order for phase B/C/D (reverse)
Class2RELCmd:  AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd:  ""  # commands to enable copy quality proc.
Class2AbortCmd:  AT+FK  # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd:  AT+FTBC=0 # setup stream mode
Class2CRCmd:  AT+FCR=1 # enable capability to receive
Class2PHCTOCmd:  AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd:  AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd:  AT+FLID  # set local identifier command
Class2DCCCmd:  AT+FDCC  # set modem capabilities command
Class2DISCmd:  AT+FDIS  # set session parameters command
Class2DDISCmd:  ""  # disable pre-dial DIS command hack
Class2CIGCmd:  AT+FCIG  # set polling identifier command
Class2PTSCmd:  AT+FPTS  # set post-page status command
Class2SPLCmd:  AT+FSPL  # set polling indicator command
Class2RecvDataTrigger: ""  # character sent to modem to start recv
Class2XmitWaitForXON: yes  # if true, wait for XON before send

----- log -----
Jul 16 16:34:25.64: [  189]: SESSION BEGIN 00000126 4930xxxxxxxx   (sorry,
no my own phone)
Jul 16 16:34:25.64: [  189]: <-- [4:ATA\r]
Jul 16 16:34:31.90: [  189]: --> [5:+FCON]
Jul 16 16:34:31.90: [  189]: ANSWER: FAX CONNECTION
Jul 16 16:34:31.90: [  189]: RECV FAX: begin
Jul 16 16:34:34.18: [  189]: --> [28:+FTSI:" 49 030 xxxxxxxx    "]
Jul 16 16:34:34.18: [  189]: REMOTE TSI "49 030 xxxxxxxx"
Jul 16 16:34:34.18: [  189]: --> [21:+FDCS:1,5,0,0,0,0,0,0]
Jul 16 16:34:34.18: [  189]: REMOTE wants 14400 bit/s
Jul 16 16:34:34.18: [  189]: REMOTE wants page width 1728 pixels in 215 mm
Jul 16 16:34:34.18: [  189]: REMOTE wants A4 page length (297 mm)
Jul 16 16:34:34.18: [  189]: REMOTE wants 7.7 line/mm
Jul 16 16:34:34.18: [  189]: REMOTE wants 1-D MR
Jul 16 16:34:35.87: [  189]: --> [2:OK]
Jul 16 16:34:35.87: [  189]: <-- [7:AT+FDR\r]
Jul 16 16:34:38.46: [  189]: --> [5:+FCFR]
Jul 16 16:34:38.46: [  189]: --> [21:+FDCS:1,5,0,0,0,0,0,0]
Jul 16 16:34:38.46: [  189]: REMOTE wants 14400 bit/s
Jul 16 16:34:38.46: [  189]: REMOTE wants page width 1728 pixels in 215 mm
Jul 16 16:34:38.46: [  189]: REMOTE wants A4 page length (297 mm)
Jul 16 16:34:38.46: [  189]: REMOTE wants 7.7 line/mm
Jul 16 16:34:38.46: [  189]: REMOTE wants 1-D MR
Jul 16 16:34:39.21: [  189]: --> [7:CONNECT]
Jul 16 16:34:39.21: [  189]: RECV: begin page
Jul 16 16:34:39.21: [  189]: RECV: send trigger 021
Jul 16 16:34:39.21: [  189]: <-- data [1]
Jul 16 16:35:44.18: [  189]: <-- data [1]
Jul 16 16:35:44.18: [  189]: RECV: Missing EOL after 5 seconds
Jul 16 16:35:44.18: [  189]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)
Jul 16 16:35:44.18: [  189]: RECV FAX (00000126): recvq/fax00009.tif from 49
030 xxxxxxxx, route to <unspecified>, 0 pages in 1:13
Jul 16 16:35:44.18: [  189]: RECV FAX: Missing EOL after 5 seconds (section
3.2/T.4)
Jul 16 16:35:44.18: [  189]: <-- [6:AT+FK\r]
Jul 16 16:35:44.41: [  189]: --> [7:+FHNG:2]
Jul 16 16:35:44.41: [  189]: REMOTE HANGUP: Call aborted,  from +FK or <CAN>
(code 2)
Jul 16 16:35:44.41: [  189]: --> [2:OK]
Jul 16 16:35:44.41: [  189]: RECV FAX (00000126): session with 49 030
xxxxxxxx terminated abnormally: Missing EOL after 5 seconds (section
3.2/T.4)
Jul 16 16:35:44.41: [  189]: RECV FAX: bin/faxrcvd "recvq/fax00009.tif"
"ttyS2" "00000126" "Missing EOL after 5 seconds (section 3.2/T.4)"
Jul 16 16:35:44.55: [  189]: RECV FAX: end
Jul 16 16:35:44.55: [  189]: SESSION END