|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Phase B Error (Code 20)
And it's not a Sportster.
Linux 2.2.9, HylaFAX-v4.0pl2, Netcomm Roadster II connected to the /dev/ttyE[0-4] interfaces. The
problem is printing from a windows application (such as IE) to the fax machine (Canon Fax 410).
Always get the Phase B Error (code 20) .. I use the HP Laserjet 4/4M Plus PS, the other PS printers
we've tried all get a busy signal when dialling the office fax machine (or is that the problem??)
The job actually reports success, but has 0 pages sent. We can send a postscript job from linux to
the fax no probs at all.
Here's a log -
Jul 28 16:47:46.24: [11716]: SESSION BEGIN 00000102 6103094822793
Jul 28 16:47:46.24: [11716]: SEND FAX: JOB 57 DEST 0,94822793 COMMID 00000102
Jul 28 16:47:46.24: [11716]: DELAY 2600 ms
Jul 28 16:47:48.84: [11716]: <-- [15:ATE0V1Q0S0=0H0\r]
Jul 28 16:47:48.86: [11716]: --> [2:OK]
Jul 28 16:47:48.86: [11716]: <-- [21:ATS8=2S7=60&K3&D3&C1\r]
Jul 28 16:47:48.89: [11716]: --> [2:OK]
Jul 28 16:47:48.89: [11716]: <-- [12:AT+FCLASS=2\r]
Jul 28 16:47:48.91: [11716]: --> [2:OK]
Jul 28 16:47:48.91: [11716]: <-- [10:AT+FTBC=0\r]
Jul 28 16:47:48.93: [11716]: --> [2:OK]
Jul 28 16:47:48.93: [11716]: <-- [10:AT+FBOR=0\r]
Jul 28 16:47:48.95: [11716]: --> [2:OK]
Jul 28 16:47:48.95: [11716]: <-- [13:AT+FPHCTO=30\r]
Jul 28 16:47:48.97: [11716]: --> [2:OK]
Jul 28 16:47:48.97: [11716]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Jul 28 16:47:48.99: [11716]: --> [2:OK]
Jul 28 16:47:48.99: [11716]: <-- [7:ATL2M1\r]
Jul 28 16:47:49.01: [11716]: --> [2:OK]
Jul 28 16:47:49.01: [11716]: <-- [12:AT+FCLASS=2\r]
Jul 28 16:47:49.13: [11716]: --> [2:OK]
Jul 28 16:47:49.13: [11716]: <-- [10:AT+FTBC=0\r]
Jul 28 16:47:49.25: [11716]: --> [2:OK]
Jul 28 16:47:49.25: [11716]: <-- [10:AT+FBOR=0\r]
Jul 28 16:47:49.37: [11716]: --> [2:OK]
Jul 28 16:47:49.37: [11716]: <-- [13:AT+FPHCTO=30\r]
Jul 28 16:47:49.49: [11716]: --> [2:OK]
Jul 28 16:47:49.49: [11716]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Jul 28 16:47:49.61: [11716]: --> [2:OK]
Jul 28 16:47:49.61: [11716]: <-- [25:AT+FLID="+6103094822793"\r]
Jul 28 16:47:49.74: [11716]: --> [2:OK]
Jul 28 16:47:49.74: [11716]: DIAL 0,94822793
Jul 28 16:47:49.74: [11716]: <-- [15:ATDT0,94822793\r]
Jul 28 16:48:10.70: [11716]: --> [5:+FCON]
Jul 28 16:48:13.37: [11716]: --> [29:+FCSI: " 613 9482 2793"]
Jul 28 16:48:13.37: [11716]: REMOTE CSI "613 9482 2793"
Jul 28 16:48:13.63: [11716]: --> [22:+FDIS: 1,3,0,2,1,0,0,2]
Jul 28 16:48:13.74: [11716]: --> [2:OK]
Jul 28 16:48:13.74: [11716]: REMOTE best rate 9600 bit/s
Jul 28 16:48:13.74: [11716]: REMOTE max page width 1728 pixels in 215 mm
Jul 28 16:48:13.74: [11716]: REMOTE max unlimited page length
Jul 28 16:48:13.74: [11716]: REMOTE best vres 7.7 line/mm
Jul 28 16:48:13.74: [11716]: REMOTE best format 2-D MR
Jul 28 16:48:13.74: [11716]: REMOTE best 10 ms, 5 ms/scanline
Jul 28 16:48:13.74: [11716]: USE 9600 bit/s
Jul 28 16:48:13.74: [11716]: USE 10 ms, 5 ms/scanline
Jul 28 16:48:13.74: [11716]: <-- [5:ATH0\r]
Jul 28 16:48:14.00: [11716]: --> [9:+FHNG: 20]
Jul 28 16:48:14.00: [11716]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Jul 28 16:48:14.59: [11716]: --> [2:OK]
Jul 28 16:48:14.59: [11716]: SESSION END
Cheers,
dga
