Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

ZyXEL 2864 ID



Hi,

i have troubles with the following installation:
HylaFaxv4.0pl2-56
SuSE Linux 6.1.1.2
Kernel 2.2.7
ZyXEL ISDN-Modem 2864ID

When i run faxsetup the modem is found correctly. After starting HylaFax
i get 1 Mail/min that the modem can't be initialised.

Any ideas ?

/var/log/messages
Jul  1 14:19:58 col FaxGetty[383]: MODEM set DTR OFF
Jul  1 14:19:58 col FaxGetty[383]: DELAY 2600 ms
Jul  1 14:20:00 col FaxGetty[383]: MODEM set DTR ON
Jul  1 14:20:00 col FaxGetty[383]: MODEM set baud rate: 38400 baud,
input flow RTS/CTS, output flow RTS/CTS
Jul  1 14:20:00 col FaxGetty[383]: MODEM flush i/o
Jul  1 14:20:00 col FaxGetty[383]: <--
[36:AT&B1&N0&S0S18=4S38.3=1E0V1Q0S0=0H0\r]
Jul  1 14:20:05 col FaxGetty[383]: MODEM TIMEOUT: reading line from
modem
Jul  1 14:20:05 col FaxGetty[383]: MODEM <Timeout>
Jul  1 14:20:05 col FaxGetty[383]: MODEM set DTR OFF

 /etc/inittab:
faxstat -srv:
HylaFAX scheduler on col.lugo: Running
Modem ttyS1 (+49.6061.921661): Waiting for modem to come ready
                                 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^
JID  Pri S  Owner Number       Pages Dials     TTS Status
1    127 W   root 0203 809 59   0:0   0:4          
Trying localhost (127.0.0.1) at port 4559...
Connected to localhost.
220 col.lugo server (HylaFAX (tm) Version 4.0pl2) ready.
-> USER root
230 User root logged in.
-> PORT 127,0,0,1,4,5
200 PORT command successful.
-> LIST status
150 Opening new data connection for "status".
226 Transfer complete.
-> JOBFMT
200 %-4j %3i %1a %6.6o %-12.12e %5P %5D %7z %.25s
-> PORT 127,0,0,1,4,6
200 PORT command successful.
-> LIST sendq
150 Opening new data connection for "sendq".
226 Transfer complete.
-> RCVFMT
200 %-7m %4p%1z %-8.8o %14.14s %7t %f
-> PORT 127,0,0,1,4,7
200 PORT command successful.
-> LIST recvq
150 Opening new data connection for "recvq".
226 Transfer complete.

config.ttyS1
# $Id: zyxel-2864,v 1.5 1997/09/27 16:03:39 guru Rel $
# Configuration for a ZyXEL 2864, 2864I, or Omni 288S in Class 2.0.
#
#
CountryCode:            49
AreaCode:               6061
FAXNumber:              +49.6061.921661
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          527
SessionTracing:         527
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-r -b -s %s %l"
LocalIdentifier:        "col Faxserver Test"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
NoCarrierRetrys:        3
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400           # 38.4 works fine
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&H0           # disable flow control
ModemHardFlowCmd:       AT&H3           # hardware flow control
ModemSoftFlowCmd:       AT&H4           # software flow control
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to hang
up
ModemSetupDCDCmd:       AT&C1           # DCD tracks carrier
#
ModemSetupAACmd:        AT+FAA=1        # enable in current class
#
# Additional reset commands:
#
# &B1     DTE-DCE rate is fixed at DTE setting
# &N0     Auto-negotiate highest possible DCE-DCE link rate
# &S0     DSR always on
# *F0     Deny remote configuration
#         (actually *F0 doesn't work in the firmware -- sigh)
# S18=4   Receive at 38400
# S38.3=1 DCD on/off sequence follows UNIX standard; also
#         fix receiving baud rate at S18 value
# 
ModemResetCmds:         AT&B1&N0&S0S18=4S38.3=1
#
ModemDialCmd:           ATDT%s          # no '@' 'cuz then busy not
recognized
NoCarrierRetrys:        3               # retry 3 times on no carrier
#
ModemSetVolumeCmd:      "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#QualifyCID:            etc/cid         # CID access control list file
#CIDNumber:             "CALLER NUMBER: " # pattern string for phone
number info
#CIDName:               "CALLER NAME: " # pattern string for identity
info
#
PagerSetupCmds:         AT&K0&N15       # use V.22 at 1200 bps (PageNet)


# getty-programs for the normal runlevels
# <id>:<runlevels>:<action>:<process>
# The "id" field  MUST be the same as the last
# characters of the device (after "tty").
1:123:respawn:/sbin/mingetty --noclear tty1

# modem getty.
# mo:23:respawn:/usr/sbin/mgetty -s 38400 modem

# fax getty (hylafax)
mo:23:respawn:/usr/lib/fax/faxgetty /dev/ttyS1



Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services