flexfax: Send but not receive ..(USR 56k probs)

[macolori@tin.it]

Hello

I installed  hylafax server 4.0.2-8  on debian 2.1 linux distribution, with
a
USR Sportster Flash 56k

I've tried to configure it and now I can to send
fac-simile to most of faxs and this is great!

but I can't to receive..

I get everytime I tried :

Jun  8 11:57:39 debian FaxGetty[4512]: MODEM U.S. ROBOTICS INC. 56.0 VOICE
/
Jun  8 11:58:21 debian FaxGetty[4512]: ANSWER: Ring detected without
successful handshake
Jun  8 11:58:29 debian FaxGetty[4512]: MODEM U.S. ROBOTICS INC. 56.0 VOICE
/

when i try to call me with the phone
I receive a tone on the line
I mean..the modem works well..beeeeeeeeeeeeeeeep
but after this nothing...why?
I tried with crtsct flow control too but nothing..


Can someone help me to receive fax?

Tanx a lot!

Mauro.

my inittab

S1:23:respawn:/usr/sbin/faxgetty ttyS1   

this is my config.ttyS1


CountryCode:            "39"
AreaCode:               464
FAXNumber:              +39.464.573850
LongDistancePrefix:     "0"
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0666
LogFileMode:            0666
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Comune di Riva del Garda"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#

ModemDialCmd:           ATX3DP0,%s   (I've tried with @ too..but is the
same)

ModemAnswerCmd:         ATA
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400           # DCE-DTE communication rate
ModemFlowControl:       xonxoff         # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C0           # setup so DCD reflects carrier (ot
not)
ModemResultCodesCmd:    ATQ0X3          # enable extended result codes


#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1L0 ATM1L1 ATM1L2 ATM1L3"

ModemCommaPauseTimeCmd: ATS0=2

#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
Class2NRCmd:            AT+FNR=1,1,1,0